Nissan X-Trail 32. Manual — part 645
REAR DOOR LOCK
DLK-921
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• When installing outside handle cable to outside handle, be careful that outside handle cable is
routed normally.
• After installation, check door lock. Refer to
DLK-921, "DOOR LOCK : Inspection"
.
DOOR LOCK : Inspection
INFOID:0000000010728716
1.
After opening and closing the door, check that door is fixed to the vehicle body normally.
2.
Check the lock/unlock operation of door lock.
3.
Check door lock assembly for poor lubrication. Apply body
grease to door lock if necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000010728717
REMOVAL
1.
Remove rear door finisher. Refer to
INT-19, "Removal and Installation"
.
2.
Remove inside handle mounting bolt.
3.
Disengage inside handle
from door panel
while sliding
inside handle toward vehicle rear, and then separate inside han-
dle.
4.
Disengage lock knob cable
and inside handle cable
from
inside handle
according to the numerical order 1
→
4 indicated
by arrows as shown in the figure.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, check door lock. Refer to
DLK-921, "DOOR LOCK : Inspection"
OUTSIDE HANDLE
: Body grease
JMKIA8534ZZ
: Pawl
JMKIB3527ZZ
JMKIB3521ZZ
DLK-922
< REMOVAL AND INSTALLATION >
[TYPE 4]
REAR DOOR LOCK
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000010728718
REMOVAL
1.
Fully close the rear door glass.
2.
Remove rear door finisher. Refer to
INT-19, "Removal and Installation"
.
3.
Remove inside handle. Refer to
DLK-921, "INSIDE HANDLE : Removal and Installation"
.
4.
Remove sealing screen and rear door lower sash. Refer to
GW-52, "REAR DOOR LOWER SASH :
.
5.
Remove door side grommet
, and then loosen TORX bolt
from grommet hole.
6.
Remove outside handle escutcheon
while pulling outside
handle grip
according to the numerical order 1
→
2 indicated
by arrows as shown in the figure.
7.
Slide outside handle grip
toward rear of vehicle and remove it
according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
JMKIB3528ZZ
JMKIB2479ZZ
JMKIA0524ZZ
REAR DOOR LOCK
DLK-923
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
8.
Remove front gasket
and rear gasket
.
9.
Slide outside handle bracket toward rear of vehicle and remove
it.
10. Disconnect outside handle cable
from outside handle bracket
according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• When installing outside handle cable to outside handle, be careful that outside handle cable is
routed normally.
• After installation, check door lock. Refer to
DLK-921, "DOOR LOCK : Inspection"
.
: Pawl
: Vehicle front
JMKIB1627ZZ
: Vehicle front
JMKIB2034ZZ
JMKIB3525ZZ
DLK-924
< REMOVAL AND INSTALLATION >
[TYPE 4]
BACK DOOR LOCK
BACK DOOR LOCK
Exploded View
INFOID:0000000010728710
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000010728711
REMOVAL
1.
Remove back door inner finisher. Refer to
INT-47, "Removal and Installation"
2.
Disconnect back door lock assembly harness connector.
3.
Remove back door lock assembly mounting bolts, and then remove back door lock assembly from back
door panel.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, check back door lock. Refer to
DLK-924, "DOOR LOCK : Inspection"
DOOR LOCK : Inspection
INFOID:0000000010728712
1.
After opening and closing the back door, check that door is fixed to the vehicle body normally.
2.
Check the lock/unlock operation of door lock.
Back door panel
Back door lock assembly
: N·m (kg-m, in-lb)
: Body grease
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB3481GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст