Nissan X-Trail 32. Manual — part 2040
TM-118
< REMOVAL AND INSTALLATION >
[6MT: RS6F52A]
DIFFERENTIAL SIDE OIL SEAL
DIFFERENTIAL SIDE OIL SEAL
Exploded View
INFOID:0000000010921092
Removal and Installation
INFOID:0000000010921093
REMOVAL
1.
Remove front drive shafts. Refer to
FAX-50, "R9M : Removal and Installation"
(4WD).
2.
Remove differential side oil seals from clutch housing and tran-
saxle case, using oil seal remover (commercial service tool).
CAUTION:
Never damage transaxle case and clutch housing.
INSTALLATION
Note the following, and install in the reverse order of removal.
Differential side oil seal
Transaxle assembly
Oil seal lip
: Vehicle front
: Always replace after every disassembly.
: Apply multi-purpose grease.
JSDIA6348ZZ
SCIA0824E
DIFFERENTIAL SIDE OIL SEAL
TM-119
< REMOVAL AND INSTALLATION >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Install differential side oil seals to clutch housing and transaxle
case, using the tool.
CAUTION:
• Never reuse differential side oil seal.
• Apply multi-purpose grease onto oil seal lip.
• Never incline differential side oil seal.
• Never damage clutch housing and transaxle case.
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000010921094
INSPECTION AFTER INSTALLATION
Check the oil level and oil leakage. Refer to
: Transaxle case side
: Clutch housing side
Dimension (C)
: 0
±
0.5 mm (0
±
0.020 in)
Dimension (D)
: 0
±
0.5 mm (0
±
0.020 in)
Tool to use
Transaxle case side
: Drift (SST: ST30720000)
Clutch housing side
: Drift (SST: ST33400001)
JSDIA6349ZZ
TM-120
< REMOVAL AND INSTALLATION >
[6MT: RS6F52A]
AIR BREATHER
AIR BREATHER
Exploded View
INFOID:0000000010921095
Removal and Installation
INFOID:0000000010921096
REMOVAL
1.
Remove battery and battery trays. Refer to
PG-143, "R9M : Removal and Installation"
.
2.
Loosen hose clamp, and remove air breather hose from transaxle assembly.
3.
Remove air breather cap and hose clamp from air breather hose.
INSTALLATION
Note the following, and install in the reverse order of removal.
• When inserting air breather cap
to air breather hose
, be sure
to insert the hose until end of the cap.
Air breather cap
Air breather hose
Hose clamp
Transaxle assembly
: Vehicle front
: Always replace after every disassembly.
JSDIA6341ZZ
JSDIA5801ZZ
AIR BREATHER
TM-121
< REMOVAL AND INSTALLATION >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Install air breather hose
so that the paint mark
and hose
clamp tab
are faced forward of the vehicle as shown in the fig-
ure.
• When inserting air breather hose to transaxle assembly, be sure to
insert it fully until its end reaches the stop.
• When installing air breather hose, make sure there are no pinched
or restricted areas on air breather hose caused by bending or
winding.
: Vehicle front
JSDIA6344ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст