Nissan X-Trail 32. Manual — part 2041
TM-122
< UNIT REMOVAL AND INSTALLATION >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
UNIT REMOVAL AND INSTALLATION
TRANSAXLE ASSEMBLY
Exploded View
INFOID:0000000010921097
Removal and Installation
INFOID:0000000010921098
CAUTION:
Never reuse CSC (Concentric Slave Cylinder). Because CSC slides back to the original position every
time when removing transaxle assembly. At this timing, dust on the sliding parts may damage a seal of
CSC and may cause clutch fluid leakage. Refer to
CL-30, "Removal and Installation"
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1.
Shift the shift lever to the neutral position.
2.
Remove engine assembly together with transaxle assembly from vehicle. Refer to
.
3.
Remove starter motor. Refer to
STR-39, "R9M : Removal and Installation"
4.
Remove clutch tube from CSC (Concentric Slave Cylinder). Refer to
CL-27, "Removal and Installation"
CAUTION:
Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately
and wash the affected area with water.
5.
Remove air breather hose. Refer to
TM-120, "Removal and Installation"
.
Transaxle assembly
Stud bolt
: N·m (kg-m, ft-lb)
JSDIA6351GB
TRANSAXLE ASSEMBLY
TM-123
< UNIT REMOVAL AND INSTALLATION >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
6.
Remove transfer gusset
. (4WD models only)
7.
Remove the bolts that fasten the transaxle assembly and engine
assembly.
8.
Remove transaxle assembly from the engine assembly.
NOTE:
For 4WD models, remove together with transfer assembly.
9.
Remove transfer assembly. (4WD models only) Refer to
181, "Removal and Installation"
10. Remove engine mounting bracket (LH). Refer to
11. Remove CSC. Refer to
CL-30, "Removal and Installation"
.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• The transaxle assembly must not interfere with the wire harnesses and clutch tube.
• When installing transaxle assembly, never bring input shaft into contact with clutch cover.
• When installing the transaxle assembly to the engine assembly,
install mounting bolts and nuts following the standard below,
tighten bolts to the specified torque. For each tightening torque,
refer to
NOTE:
Symbol
is composed a stud bolt and a nut.
• When installing engine mounting bracket (LH)
to transaxle
assembly, temporarily tighten the short bolt
then tighten the
mounting bolts to the specified torque in the order shown in the fig-
ure. For tightening torque, refer to
.
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000010921099
INSPECTION AFTER INSTALLATION
Check the oil leakage and the oil level. Refer to
.
JSDIA6418ZZ
Bolt/Nut symbol
Quantity
2
2
4
Bolt length
“
” mm (in)
—
55 (2.17)
55 (2.17)
Insertion direction
Transaxle to engine
Engine to transaxle
JSDIA6357ZZ
JSDIA6364ZZ
TM-124
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
UNIT DISASSEMBLY AND ASSEMBLY
TRANSAXLE ASSEMBLY
2WD
2WD : Exploded View
INFOID:0000000010919402
CASE AND HOUSING
Differential side oil seal
Clutch housing
Input shaft oil seal
Oil channel
Oil gutter A
Back-up lamp switch
Plunger
Gasket
Plug
Bore plug
Striking rod oil seal
Transaxle case
Oil gutter B
Air breather tube
Neutral position switch
Shift lever oil seal
Drain plug
Magnet
O-ring
Plug
Oil seal lip
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JSDIA6360GB
TRANSAXLE ASSEMBLY
TM-125
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SHAFT AND GEAR
CAUTION:
Apply gear oil to gears, shafts, synchronizers, and bearings when assembly.
: Always replace after every disassembly.
: Apply multi-purpose grease.
: Apply Genuine Liquid Gasket, Three Bond 1215 or an equivalent.
Input shaft front bearing
Input shaft
3rd needle bearing
3rd input gear
3rd inner baulk ring
3rd synchronizer cone
3rd outer baulk ring
3rd-4th spread spring
3rd-4th shifting insert
3rd-4th synchronizer hub
4th baulk ring
3rd-4th coupling sleeve
4th input gear bushing
4th needle bearing
4th input gear
Thrust washer
5th input gear bushing
5th needle bearing
5th input gear
5th baulk ring
5th-6th spread spring
5th-6th shifting insert
5th-6th synchronizer hub
5th-6th coupling sleeve
6th baulk ring
6th input gear
6th needle bearing
6th input gear bushing
Snap ring
Input shaft rear bearing
Oil channel
Input shaft rear bearing adjusting
shim
: Always replace after every disassembly.
: Select with proper thickness.
: Replace the parts as a set.
JSDIA6366ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст