Nissan X-Trail 32. Manual — part 571

FUEL FILLER LID OPENER

DLK-625

< REMOVAL AND INSTALLATION >

[TYPE 2]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

4.

Disengage fuel filler lid opener cable

and remove fuel filler lid

opener cable while pressing stopper pin

according to the

numerical order 1

→

4 indicated by arrows as shown in the figure.

INSTALLATION

Note the following item, and then install in the reverse order of removal.

CAUTION:

After installation, check fuel filler lid assembly open/close, lock/unlock operation.

FUEL FILLER OPENER CABLE

FUEL FILLER OPENER CABLE : Removal and Installation

INFOID:0000000010728172

REMOVAL

1.

Remove hood lock control handle mounting bolts, and then hood lock control handle. Refer to

DLK-607,

"HOOD LOCK CONTROL HANDLE : Removal and Installation"

.

2.

Remove fuel filler lid opener cable

from fuel filler lid opener

lever

according to the numerical order 1

→

2 indicated by

arrows as shown in the figure.

3.

Remove kicking plate inner LH and rear kicking plate inner (LH and RH). Refer to

INT-24, "KICKING

PLATE : Removal and Installation"

.

4.

Remove dash side finisher LH. Refer to

INT-26, "DASH SIDE FINISHER : Removal and Installation"

.

5.

Remove center pillar lower garnish LH. Refer to

INT-27, "CENTER PILLAR LOWER GARNISH : Removal

and Installation"

.

6.

Remove luggage side lower finisher RH. Refer to

INT-43, "LUGGAGE SIDE LOWER FINISHER :

Removal and Installation"

.

7.

Remove fuel filler lid opener cable from fuel filler lid lock assembly. Refer to

DLK-624, "FUEL FILLER LID

LOCK : Removal and Installation"

.

8.

Remove fuel filler lid opener cable from harness protectors.

9.

Remove fuel filler lid opener cable fixing clips, and then remove fuel filler lid opener cable.

INSTALLATION

Note the following item, and then install in the reverse order of removal.

CAUTION:

After installation, check fuel filler lid assembly open/close, lock/unlock operation.

JMKIA5719ZZ

JMKIA5901ZZ

DLK-626

< REMOVAL AND INSTALLATION >

[TYPE 2]

DOOR SWITCH

DOOR SWITCH

Removal and Installation

INFOID:0000000010717716

REMOVAL

1.

Remove the TORX bolt

.

2.

Disconnect door switch harness connector and then remove
door switch

.

INSTALLATION

Install in the reverse order of removal.

JMKIA2173ZZ

INSIDE KEY ANTENNA

DLK-627

< REMOVAL AND INSTALLATION >

[TYPE 2]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

INSIDE KEY ANTENNA

INSTRUMENT CENTER

INSTRUMENT CENTER : Removal and Installation

INFOID:0000000010717717

REMOVAL

1.

Remove A/C control. Refer to

HAC-125, "Removal and Installation"

.

2.

Disconnect inside key antenna (instrument center) harness connector.

3.

Remove inside key antenna (instrument center) mounting clip

, and then remove inside key antenna (instrument center)

.

INSTALLATION

Install in the reverse order of removal.

LUGGAGE ROOM

LUGGAGE ROOM : Removal and Installation

INFOID:0000000010717718

REMOVAL

3 Seat Rows

1.

Remove rear seat. Refer to

SE-54, "Removal and Installation"

.

2.

Disconnect inside key antenna (luggage room) harness connector.

3.

Remove inside key antenna (luggage room) mounting clip

,

and then remove inside key antenna (luggage room)

.

2 Seat Rows

1.

Remove luggage floor board. Refer to

INT-40, "Exploded View"

.

2.

Disconnect inside key antenna (luggage room) harness connector.

JMKIB2755ZZ

JMKIB2756ZZ

DLK-628

< REMOVAL AND INSTALLATION >

[TYPE 2]

INSIDE KEY ANTENNA

3.

Remove inside key antenna (luggage room) mounting clip

,

and then remove inside key antenna (luggage room)

.

INSTALLATION

Install in the reverse order of removal.

JMKIB3602ZZ