Nissan X-Trail 32. Manual — part 1840
B2602 SHIFT POSITION
SEC-127
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2602 SHIFT POSITION
DTC Description
INFOID:0000000010922160
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connectors
(CAN communication line is open or shorted.)
• Harness or connectors
[CVT shift selector (detention switch) circuit is open or shorted.]
• CVT shift selector (detention switch)
• Combination meter
• ABS actuator and electric unit (control unit)
FAIL-SAFE
Inhibit steering lock
DTC CONFIRMATION PROCEDURE
1.
CHECK DTC PRIORITY
If DTC B2602-00 is displayed with DTC U1000-00 or U1010-00, first perform the trouble diagnosis for DTC
U1000-00 or U1010-00.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. U1000-00: Refer to
NO
>> GO TO 2
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine.
2.
Drive vehicle at a speed of 4 km/h (2.5 MPH) or more for 10 seconds or more.
3.
Select “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Refer to
SEC-127, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010922161
1.
CHECK DTC PRIORITY
If DTC B2602-00 is displayed with DTC U1000-00 or U1010-00, first perform the trouble diagnosis for DTC
U1000-00 or U1010-00.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. U1000-00: Refer to
NO
>> GO TO 2
2.
CHECK DTC OF “ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)”
Select “Self Diagnostic Result” mode of “ABS” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
.
NO
>> GO TO 3.
DTC No.
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B2602-00
SHIFT POSITION
(Shift position)
BCM detects the following status for 10 seconds.
• Selector lever is in the P position
• Vehicle speed is 4 km/h (2.5 MPH) or more
• Ignition switch is in the ON position
SEC-128
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2602 SHIFT POSITION
3.
CHECK DTC OF COMBINATION METER
Select “Self Diagnostic Result” mode of “METER/M&A” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
.
NO
>> GO TO 4.
4.
CHECK CVT SHIFT SELECTOR POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect CVT shift selector (detention switch) connector.
3.
Check voltage between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 5.
5.
CHECK CVT SHIFT SELECTOR POWER SUPPLY CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between CVT shift selector (detention switch) harness connector and BCM harness con-
nector.
3.
Check continuity between CVT shift selector (detention switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
REPLACE BCM
Replace BCM. Refer to
BCS-121, "Removal and Installation"
.
>> INSPECTION END
7.
CHECK CVT SHIFT SELECTOR CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between CVT shift selector (detention switch) harness connector and BCM harness con-
nector.
3.
Check continuity between CVT shift selector (detention switch) harness connector and ground.
(+)
(–)
Voltage
CVT shift selector (detention switch)
Connector
Terminal
M52
12
Ground
9 - 16 V
CVT shift selector (detention switch)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M52
12
M87
57
Existed
CVT shift selector (detention switch)
Ground
Continuity
Connector
Terminal
M52
12
Not existed
CVT shift selector (detention switch)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M52
13
M86
94
Existed
B2602 SHIFT POSITION
SEC-129
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace harness.
8.
CHECK CVT SHIFT SELECTOR (DETENTION SWITCH)
SEC-129, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Replace CVT shift selector. Refer to
TM-403, "Removal and Installation"
(RE0F10G).
9.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000010922162
1.
CHECK CVT SHIFT SELECTOR (DETENTION SWITCH)
1.
Turn ignition switch OFF.
2.
Disconnect CVT shift selector connector.
3.
Check continuity between CVT shift selector (detention switch) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace CVT shift selector. Refer to
TM-403, "Removal and Installation"
(RE0F10G).
CVT shift selector (detention switch)
Ground
Continuity
Connector
Terminal
M52
13
Not existed
CVT shift selector (detention switch)
Condition
Continuity
Terminal
12
13
Selector lever: P position
Selector button: Released
Not existed
Selector button: Pressed
Existed
Selector lever: Except P position
SEC-130
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2604 SHIFT POSITION
B2604 SHIFT POSITION
DTC Description
INFOID:0000000010922163
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connectors
(CAN communication line is open or shorted.)
• Harness or connectors
(Transmission range switch circuit is open or shorted.)
• Transmission range switch
• IPDM E/R
• TCM
FAIL-SAFE
Inhibit steering lock
DTC CONFIRMATION PROCEDURE
1.
CHECK DTC PRIORITY
If DTC B2604-00 is displayed with DTC U1000-00 or U1010-00, first perform the trouble diagnosis for DTC
U1000-00 or U1010-00.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. U1000-00: Refer to
NO
>> GO TO 2
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Shift the selector lever to the P position.
2.
Turn ignition switch ON and wait 5 seconds or more.
3.
Shift the selector lever to the N position and wait 5 seconds or more.
4.
Shift the selector lever to any position other than P and N, and wait 5 seconds or more.
5.
Select “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Refer to
SEC-130, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010922164
1.
CHECK DTC PRIORITY
If DTC B2604-00 is displayed with DTC U1000-00 or U1010-00, first perform the trouble diagnosis for DTC
U1000-00 or U1010-00.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. U1000-00: Refer to
NO
>> GO TO 2.
2.
CHECK DTC OF TCM
Select “Self Diagnostic Result” mode of “TCM” using CONSULT.
DTC No.
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B2604-00
PNP/CLUTCH SW
(Park neutral position/ clutch
switch)
The following states are detected for 5 seconds while ignition switch is ON.
• Interlock/PNP signal (CAN) is not sent from IPDM E/R but shift position signal
input (CAN) from TCM is P or N
• Interlock/PNP signal (CAN) is sent from IPDM E/R but shift position signal in-
put (CAN) from TCM is other than P and N
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст