Nissan X-Trail 32. Manual — part 1841
B2604 SHIFT POSITION
SEC-131
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
(RE0F10G).
NO
>> GO TO 3.
3.
CHECK FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuse is not blown.
With engine start/stop system
Without engine start/stop system
Is the fuse fusing?
Yes
>> GO TO 4.
NO
>> Replace the blown fuse after repairing the cause of blown.
4.
CHECK TRANSMISSION RANGE SWITCH POWER SUPPLY
1.
Disconnect transmission range switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between transmission range switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK IPDM E/R INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Connect transmission range switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> GO TO 6.
6.
CHECK TRANSMISSIONRANGE SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect transmission range switch connector and IPDM E/R connector.
3.
Check continuity between transmission range switch harness connector and BCM harness connector.
Signal name
Fuse No.
Ignition power supply
57 (10A)
Signal name
Fuse No.
Ignition power supply
93 (10A)
(+)
(–)
Voltage
Transmission range switch
Connector
Terminal
F22
1
Ground
Battery voltage
(+)
(–)
Condition
Voltage
IPDM E/R
Connector
Terminal
F74
92
Ground
Selector lever
P or N position
9 - 16
Other than above
0 - 1
Transmission range switch
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
F22
2
F74
92
Existed
SEC-132
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2604 SHIFT POSITION
4.
Check continuity between transmission range switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
CHECK TRANSMISSION RANGE SWITCH
SEC-132, "Component Inspection"
.
Is the inspection the result normal?
YES
>> INSPECTION END
NO
>> Replace transmission. Refer to
TM-450, "Removal and Installation"
(RE0F10D) or
(RE0F10G).
8.
REPLACE IPDM E/R
PCS-60, "Removal and Installation"
.
>> INSPECTION END
Component Inspection
INFOID:0000000010922165
1.
CHECK TRANSMISSION RANGE SWITCH
1.
Disconnect transmission range switch.
2.
Check continuity between transmission range switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace Transmission assembly. Refer to
TM-450, "Removal and Installation"
(RE0F10D) or
704, "Removal and Installation"
(RE0F10G).
Transmission range switch
Ground
Continuity
Connector
Terminal
F22
2
Not existed
Transmission range switch
Condition
Continuity
Terminal
1
2
Select lever
P or N position
Existed
Other than above
Not existed
B2608 STARTER RELAY
SEC-133
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2608 STARTER RELAY
DTC Description
INFOID:0000000010922166
DTC DETECTION LOGIC
POSSIBLE CAUSE
• IPDM E/R
• BCM
FAIL-SAFE
Inhibit engine cranking
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Press push-button ignition switch under the following conditions to start engine.
-
Selector lever: In the P position
-
Brake pedal: Depressed
2.
Wait 1 second after engine started.
3.
Select “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Refer to
SEC-133, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010922167
1.
CHECK DTC OF IPDM E/R
Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
.
NO
>> GO TO 2.
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace BCM. Refer to
BCS-121, "Removal and Installation"
.
DTC No.
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B2608-00
STARTER RELAY
(Starter relay)
BCM outputs starter relay OFF signal but BCM receives starter relay
ON signal from IPDM E/R (CAN).
SEC-134
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B260F ENGINE STATUS
B260F ENGINE STATUS
DTC Description
INFOID:0000000010922168
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connectors
(CAN communication line is open or shorted.)
• ECM
FAIL-SAFE
Inhibit engine cranking
DTC CONFIRMATION PROCEDURE
1.
CHECK DTC PRIORITY
If DTC B260F-00 is displayed with DTC U1000-00 or U1010-00, first perform the trouble diagnosis for DTC
U1000-00 or U1010-00.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. U1000-00: Refer to
NO
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait 2 seconds or more.
2.
Select “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Refer to
SEC-134, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010922169
1.
CHECK DTC PRIORITY
If DTC B260F-00 is displayed with DTC U1000-00 or U1010-00, first perform the trouble diagnosis for DTC
U1000-00 or U1010-00.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. U1000-00: Refer to
NO
>> GO TO 2.
2.
INSPECTION START
1.
Turn ignition switch ON.
2.
Select “Self Diagnostic Result” mode of “BCM” using CONSULT.
3.
Touch “ERASE”.
4.
Perform DTC CONFIRMATION PROCEDURE for DTC B260F-00. Refer to
Is DTC detected?
YES
>> GO TO 3.
NO
>> INSPECTION END
3.
REPLACE ECM
Replace ECM.
DTC No.
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B260F-00
ENG STATE SIG LOST
(Engine state signal lost)
BCM has not yet received the engine status signal from ECM when
ignition switch is in the ON position.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст