Nissan X-Trail 32. Manual — part 283
CHG-48
< SERVICE DATA AND SPECIFICATIONS (SDS)
[TYPE 2]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Alternator
INFOID:0000000010957591
Applied model
MR engine
QR engine
Type
2620093
2620168
Valeo Make
Valeo Make
Nominal rating
[V - A]
12 - 120
12 - 120
Ground polarity
Negative
Negative
Minimum revolution under no-load
(When 13.5 V is applied)
[rpm]
Less than 1,200
Less than 1,200
Hot output current
(When 13.5 V is applied)
[A/rpm]
More than 46/1,500
More than 96/2,500
More than 117/5,000
More than 46/1,500
More than 96/2,500
More than 117/5,000
Regulated output voltage
[V]
14.0 – 14.6
14.0 – 14.6
CL-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
CL
A
B
CL
N
O
P
CONTENTS
CLUTCH
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect . . . . . . . . .....
Precaution for Procedure without Cowl Top Cover
. ..
Precautions for Removing Battery Terminal . . .....
Precaution for Stop/Start System Service . . . .....
Service Notice or Precautions for Clutch . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ....
Commercial Service Tools . . . . . . . . . ....
Lubricant or/and Sealant . . . . . . . . . . ...
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
CLUTCH PEDAL . . . . . . . . . . . . .
Inspection and Adjustment . . . . . . . . . ....
CLUTCH FLUID . . . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . .
Draining . . . . . . . . . . . . . . . . ...
Refilling . . . . . . . . . . . . . . . . ...
Air Bleeding . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
CLUTCH PEDAL . . . . . . . . . . . .
LHD . . . . . . . . . . . . . . . . . . .
LHD : Exploded View . . . . . . . . . . . ..
LHD : Removal and Installation . . . . . . . ...
LHD : Inspection and Adjustment . . . . . . .
RHD . . . . . . . . . . . . . . . . . . .
RHD : Exploded View . . . . . . . . . . . ..
RHD : Removal and Installation . . . . . . . ..
RHD : Inspection and Adjustment . . . . . . ...
CLUTCH MASTER CYLINDER . . . . . .
LHD . . . . . . . . . . . . . . . . . . .
LHD : Exploded View . . . . . . . . . . . ...
LHD : Removal and Installation . . . . . . . ...
LHD : Inspection and Adjustment . . . . . . .
RHD . . . . . . . . . . . . . . . . . . .
RHD : Exploded View . . . . . . . . . . . ..
RHD : Removal and Installation . . . . . . . ..
RHD : Inspection and Adjustment . . . . . . ...
CLUTCH PIPING . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Hydraulic Piping . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
Inspection and Adjustment . . . . . . . . . ..
CSC (CONCENTRIC SLAVE CYLINDER) . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection and Adjustment . . . . . . . . . ..
CLUTCH DISC AND CLUTCH COVER . . .
MR20DD . . . . . . . . . . . . . . . . . .
MR20DD : Exploded View . . . . . . . . . ...
MR20DD : Removal and Installation . . . . . ...
MR20DD : Inspection . . . . . . . . . . . ..
R9M . . . . . . . . . . . . . . . . . . .
R9M : Exploded View . . . . . . . . . . . ..
R9M : Removal and Installation . . . . . . . ...
CL-2
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ...
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . ..
General Specifications . . . . . . . . . . .
Clutch Pedal . . . . . . . . . . . . . . .
Clutch Disc . . . . . . . . . . . . . . . ..
PRECAUTIONS
CL-3
< PRECAUTION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010745311
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000010745312
CAUTION:
Comply with the following cautions to prevent any error and malfunction.
• Before removing and installing any control units, first turn the ignition power source and accessory
power source to the OFF, then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect
both battery cables.
• Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing
work. If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Open driver door.
3.
Turn the ignition switch to the ON position.
(At this time, the steering lock will be released.)
4.
Turn the ignition switch to OFF position with driver door open.
5.
Wait for 3 minutes or longer with driver door open.
NOTE:
• Do not close driver door because the steering wheel locks when driver door is closed.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст