Nissan X-Trail 32. Manual — part 601
FRONT DOOR
DLK-745
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000010728553
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove dash side finisher. Refer to
INT-26, "DASH SIDE FINISHER : Removal and Installation"
.
2.
Remove SMJ (super multiple junction).
3.
Disconnect front door harness connectors
.
4.
Remove front door harness grommet
from vehicle body
,
and then pull out front door harness from vehicle body.
5.
Remove mounting bolt of door check link on vehicle body.
6.
Remove door hinge mounting nuts of door side, and then remove front door assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• After installation, perform the fitting adjustment. Refer to
DLK-746, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
Door striker
TORX bolt
Grommet
Front door weather-strip
Front door weather-strip clip
: Clip
: Pawl
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Body grease
JMKIB3019ZZ
JMKIB3020ZZ
DLK-746
< REMOVAL AND INSTALLATION >
[TYPE 3]
FRONT DOOR
• After installation, check that door opens and closes normally. Refer to
DOOR ASSEMBLY : Inspection
INFOID:0000000010728554
1.
Open and close the door. Check that door hinge and check link rotation portion moves smoothly.
2.
Check door hinge rotating part for poor lubrication. Apply body
grease if necessary.
3.
Check door check link rotating part for poor lubrication. Apply
body grease if necessary.
DOOR ASSEMBLY : Adjustment
INFOID:0000000010728555
FITTING ADJUSTMENT
: Body grease
JMKIB0321ZZ
: Body grease
JMKIB0322ZZ
FRONT DOOR
DLK-747
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Fitting Adjustment Standard
Check the clearance and surface height between front door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Front fender
Front door
Rear door
Body side outer
Door striker
TORX bolt
Front door hinge
Rear door hinge (upper)
Rear door hinge (lower)
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Body grease
JMKIB3479GB
DLK-748
< REMOVAL AND INSTALLATION >
[TYPE 3]
FRONT DOOR
Unit: mm [in]
Fitting Adjustment Procedure
1.
Remove front fender assembly. Refer to
DLK-741, "FRONT FENDER : Removal and Installation"
.
2.
Loosen door hinge mounting nuts of door side.
3.
Adjust the surface height of front door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting bolts of vehicle body side.
6.
Raise front door at rear end to adjust clearance of the front door according to the fitting standard dimen-
sion.
7.
After adjustment, tighten bolts and nuts to the specified torque.
CAUTION:
After installation, apply touch-up paint (the body color) onto the head of hinge mounting bolts and
nuts.
8.
Install front fender assembly. Refer to refer to
DLK-741, "FRONT FENDER : Removal and Installation"
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000010728556
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never reuse TORX bolt. Always replace it with a new one when it is removed.
• After installation, perform the fitting adjustment. Refer to
DLK-746, "DOOR ASSEMBLY : Adjust-
• After installation, check that door opens and closes normally. Refer to
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000010728557
REMOVAL
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
1.
Remove front door assembly. Refer to
DLK-745, "DOOR ASSEMBLY : Removal and Installation"
.
2.
Remove front fender assembly. Refer to
DLK-741, "FRONT FENDER : Removal and Installation"
.
3.
Remove front door hinge mounting bolts of vehicle body side, and then remove front door hinge.
INSTALLATION
Portion
Standard
Front fender – Front door
–
H
Clearance
3.0 – 5.0
[0.118 – 0.197]
I
Surface height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
Front door – Rear door
–
J
Clearance
3.3 – 5.3
[0.130 – 0.209]
K
Surface height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст