Nissan X-Trail 32. Manual — part 608
FRONT DOOR LOCK
DLK-773
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT DOOR LOCK
Exploded View
INFOID:0000000010728583
DOOR LOCK
Outside handle escutcheon
Outside handle grip
Front gasket
Outside handle bracket
Inside handle
Cable clip
Door lock assembly
TORX bolt
Key rod protector (driver side)
Key rod (driver side)
Rear gasket
: Pawl
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB3667GB
DLK-774
< REMOVAL AND INSTALLATION >
[TYPE 3]
FRONT DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000010728584
REMOVAL
1.
Disconnect lock knob cable and inside handle cable from inside handle. Refer to
DLE : Removal and Installation"
2.
Disconnect outside handle cable from outside handle bracket. Refer to
.
3.
Disconnect door lock assembly connector.
4.
Remove door lock assembly TORX bolts, and then remove door lock assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never reuse TORX bolt. Always replace it with a new one when it is removed.
• When installing outside handle cable to outside handle, be careful that outside handle cable is
routed normally.
• When installing key rod, rotate key rod holder until a click is felt.
• After installation, check door lock. Refer to
DLK-774, "DOOR LOCK : Inspection"
.
DOOR LOCK : Inspection
INFOID:0000000010728585
1.
After opening and closing the door, check that door is fixed to the vehicle body normally.
2.
Check the lock/unlock operation of door lock.
3.
Check door lock assembly for poor lubrication. Apply body
grease to door lock if necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000010728586
REMOVAL
1.
Remove front door finisher. Refer to
INT-14, "Removal and Installation"
2.
Remove inside handle mounting bolt.
3.
Disengage inside handle
from door panel
while sliding
inside handle toward vehicle rear, and then separate inside han-
dle.
: Body grease
JMKIA8534ZZ
: Pawl
JMKIB3668ZZ
FRONT DOOR LOCK
DLK-775
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4.
Disengage inside handle cable
from inside handle
accord-
ing to the numerical order 1
→
2 indicated by arrows as shown in
the figure.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, check door lock. Refer to
DLK-774, "DOOR LOCK : Inspection"
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000010728587
REMOVAL
1.
Fully close the front door glass.
2.
Remove front door finisher. Refer to
INT-14, "Removal and Installation"
3.
Remove inside handle. Refer to
DLK-774, "INSIDE HANDLE : Removal and Installation"
.
4.
Remove sealing screen and front door glass run lower sash. Refer to
RUN LOWER SASH : Removal and Installation"
.
5.
Remove key rod protector mounting bolt and fixing clip, and then remove key rod protector.
6.
Disengage outside handle cable
from cable clip
.
JMKIB3669ZZ
: Vehicle front
JMKIB3670ZZ
DLK-776
< REMOVAL AND INSTALLATION >
[TYPE 3]
FRONT DOOR LOCK
7.
Disengage rod holder
and disconnect key rod
from door lock assembly
according to the numerical
order 1
→
2 indicated by arrows as shown in the figure (driver side).
8.
Remove door side grommet
, and then loosen TORX bolt
from grommet hole.
9.
Remove outside handle escutcheon
while pulling outside
handle grip
according to the numerical order 1
→
2 indicated
by arrows as shown in the figure.
: Vehicle front
JMKIB3672ZZ
JMKIB3066ZZ
JMKIA0441ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст