Nissan X-Trail 32. Manual — part 607
HOOD LOCK
DLK-769
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2.
Disconnect hood lock bell crank cable from hood lock assembly. Refer to
CRANK : Removal and Installation"
.
3.
Remove hood lock assembly mounting bolts, and then remove hood lock assembly.
4.
Disconnect hood lock control cable assembly
from hood lock
assembly
according to the numerical order 1
→
2 indicated by
arrows as shown in the figure.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never bend cable too much, keeping the radius 100 mm (3.937 in) or more.
• Check that hood lock control cable is properly engaged with hood lock.
• After installation, perform hood fitting adjustment. Refer to
DLK-733, "HOOD ASSEMBLY : Adjust-
• After installation, perform hood lock control inspection. Refer to
.
HOOD LOCK : Inspection
INFOID:0000000010728579
NOTE:
If the hood lock cable is bent or deformed, replace it.
1.
Check that hood opener operating is condition 49 N (5.0 kg, 11.0 lb) or below.
2.
Check that secondary latch
is securely engaged with second-
ary striker
from the dead load of hood assembly.
3.
Check that primary latch
is securely engaged with primary
striker
when hood assembly is closed [free-fall from approxi-
mately 200 mm (7.874 in) height].
4.
While operating the hood opener carefully, check that the front end of the hood is lifted by approximately
20 mm (0.787 in) (A). Also, check that the hood opener returns to the original position.
JMKIB2975ZZ
JMKIB3518ZZ
JMKIB3551ZZ
DLK-770
< REMOVAL AND INSTALLATION >
[TYPE 3]
HOOD LOCK
5.
Check that secondary latch is properly engaged with secondary striker [6.8 mm (0.268 in)] (B).
6.
Check the hood lock lubrication condition. If necessary, apply body grease to hood lock.
• Hood lock assembly
• Hood lock bell crank assembly
HOOD LOCK CONTROL HANDLE
HOOD LOCK CONTROL HANDLE : Removal and Installation
INFOID:0000000010728580
REMOVAL
1.
Remove hood lock control handle mounting bolts, and then remove hood lock control handle.
2.
Remove hood lock control cable
from hood opener lever
according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
Secondary striker
Secondary latch
Primary striker
Primary latch
JMKIB3487ZZ
: Body grease
JMKIB2979ZZ
: Body grease
JMKIB2980ZZ
JMKIB0327ZZ
HOOD LOCK
DLK-771
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Remove fuel filler lid opener cable from fuel filler lid opener lever. Refer to
OPENER CABLE : Removal and Installation"
.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, perform hood lock control inspection. Refer to
DLK-769, "HOOD LOCK : Inspection"
.
HOOD LOCK CONTROL CABLE
HOOD LOCK CONTROL CABLE : Removal and Installation
INFOID:0000000010728581
REMOVAL
1.
Disconnect hood lock control cable assembly from hood lock assembly. Refer to
2.
Remove fender protector RH. Refer to
EXT-35, "FENDER PROTECTOR : Removal and Installation"
3.
Remove hood lock control cable fixing clips.
4.
Disconnect hood lock control cable assembly from hood lock control handle. Refer to
LOCK CONTROL HANDLE : Removal and Installation"
.
5.
Remove dash side finisher RH. Refer to
INT-26, "DASH SIDE FINISHER : Removal and Installation"
6.
Remove grommet of the lower dash, and pull the hood lock control cable assembly toward inside vehicle.
CAUTION:
While pulling, never damage (peeling) the outside of hood lock control cable.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never bend cable too much, keeping the radius 100 mm (3.937 in) or more.
• Install grommet in the panel hole surely.
• Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet
properly.
• After installation, perform hood lock control inspection. Refer to
.
HOOD LOCK BELL CRANK
HOOD LOCK BELL CRANK : Removal and Installation
INFOID:0000000010728582
REMOVAL
JMKIA5814ZZ
DLK-772
< REMOVAL AND INSTALLATION >
[TYPE 3]
HOOD LOCK
1.
Disengage pawls of hood lock bell crank cable and disconnect hood lock bell crank cable
from housing
bracket
of hood lock assembly according to the numerical order 1
→
2 indicated by arrows as shown in
the figure.
2.
Disconnect hood lock bell crank cable
from lever
of hood lock assembly according to the numerical
order 1
→
2 indicated by arrows as shown in the figure.
3.
Remove hood lock bell crank assembly mounting bolts, and then remove hood lock bell crank assembly.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, perform hood lock control inspection. Refer to
DLK-769, "HOOD LOCK : Inspection"
.
: Pawl
: Vehicle front
JMKIB2981ZZ
: Vehicle front
JMKIB2982ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст