Nissan X-Trail 32. Manual — part 2021
TM-42
< UNIT REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
• When installing transaxle assembly, never bring input shaft into contact with clutch cover.
• When installing the transaxle assembly to the engine assembly,
install mounting bolts following the standard below, tighten bolts to
the specified torque. For each tightening torque, refer to
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000010842461
INSPECTION AFTER INSTALLATION
Check the oil leakage and the oil level. Refer to
Bolt symbol
Quantity
3
6
Bolt length
“
” mm (in)
60 (2.36)
50 (1.97)
Insertion direction
Transaxle to engine
Engine to transaxle
JPDIC0837ZZ
TRANSAXLE ASSEMBLY
TM-43
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
TRANSAXLE ASSEMBLY
Exploded View
INFOID:0000000010842462
CASE AND HOUSING
Filler plug
Gasket
Transaxle case
Bushing
Snap ring
Oil channel
Oil gutter
Position switch
Bracket
Differential side oil seal
Magnet
Drain plug
Input shaft oil seal
Clutch housing
2 way connector
Plug
Pinion shaft
Pinion gear
: N·m (kg-m, in-lb)
JPDIC0437GB
TM-44
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
SHAFT AND GEAR
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
: Select with proper thickness.
: Apply Genuine Liquid Gasket, Three Bond 1215 or an equivalent.
Input shaft front bearing
Input shaft
3rd input gear
Spacer
Snap ring
3rd baulk ring
3rd-4th coupling sleeve
3rd-4th synchronizer hub
Insert key
4th baulk ring
4th input gear
5th input gear
5th baulk ring
5th-6th coupling sleeve
5th-6th synchronizer hub
6th baulk ring
Needle bearing
6th input gear
Input shaft rear bearing
First step
Final step
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JPDIC0407GB
TRANSAXLE ASSEMBLY
TM-45
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
: Apply gear oil.
: Replace the parts as a set.
Mainshaft front bearing outer
race
Mainshaft front bearing inner race
Mainshaft
1st main gear
1st inner baulk ring
1st synchronizer cone
1st outer baulk ring
1st-2nd coupling sleeve
Insert key
1st-2nd synchronizer hub
2nd outer baulk ring
2nd synchronizer cone
2nd inner baulk ring
2nd main gear
Bushing
3rd main gear
Mainshaft adjusting shim
4th main gear
5th main gear
6th main gear
Mainshaft rear bearing inner race
Mainshaft rear bearing outer race
Snap ring
Mainshaft rear bearing adjusting
shim
: Always replace after every disassembly.
: Select with proper thickness.
: Apply gear oil.
: Replace the parts as a set.
SFIA3293E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст