Nissan X-Trail 32. Manual — part 2046
TM-142
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
24. Install shift lever (inner)
and shift lever (outer)
to transaxle
case.
CAUTION:
Be careful with the orientation of shift lever (inner) and shift
lever (outer).
25. Install retaining pin to shift lever (outer).
CAUTION:
• Never reuse retaining pin.
• Assemble retaining pin from the direction shown by the
arrow in the figure until it becomes flush with the end sur-
face of shift lever (outer).
26. Install transaxle case, as per the following procedure.
a.
Install selected mainshaft rear bearing adjusting shim into transaxle case.
• For selection of adjusting shim, refer to
TM-147, "2WD : Inspection and Adjustment"
b.
Install oil gutter A
and oil gutter B
to transaxle case.
CAUTION:
Insert the tab
of oil gutter A and oil gutter B into transaxle
case.
c.
Temporarily install snap ring of mainshaft rear bearing into tran-
saxle case.
CAUTION:
Never reuse snap ring.
PCIB1843E
PCIB1844E
PCIB1841E
PCIB1842E
TRANSAXLE ASSEMBLY
TM-143
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
d.
Apply recommended sealant to mating surface of clutch housing
as shown in the figure.
• For sealant to use, refer to
CAUTION:
• Remove old sealant adhering to the mounting surfaces.
Also remove any moisture, oil, or foreign material adher-
ing to both mounting surfaces.
• Apply sealant so as not to break the bead.
• The width of sealant bead is 1 – 2 mm (0.04 – 0.08 in).
• The height of sealant bead is 0.4 – 1 mm (0.016 – 0.04 in).
• The overlap length of both ends of sealant bead is 3 – 5
mm (0.12 – 0.20 in).
e.
With shift lever (outer)
held in the position shown in the figure,
temporarily assemble transaxle case to clutch housing.
CAUTION:
Never damage striking rod oil seal.
NOTE:
Make sure to hold shift lever (outer) in the position shown in the
figure. Otherwise transaxle case cannot be installed to clutch
housing.
f.
While rotating shift lever (outer)
in the direction of the arrow in
the figure, assemble transaxle case to clutch housing.
NOTE:
The shift lever (inner) can be inserted into the groove of striking
rod.
g.
Accessing from the bore plug hole, expand snap ring at main-
shaft rear bearing so that the ring catches the periphery of main-
shaft rear bearing.
h.
Temporarily tighten transaxle case mounting bolts.
i.
Shift the shift lever (outer)
to 2nd gear position.
NOTE:
• The 2nd gear position is attained when shift lever (outer) is in
the position shown in the figure.
PCIB1807E
JPDIC0140ZZ
: Shift lever (inner)
JPDIC0141ZZ
PCIB1840E
PCIB1809E
TM-144
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
• When transaxle is shifted to the 2nd gear position, mainshaft
assembly
is
lifted.
j.
Seat snap ring in the groove on mainshaft rear bearing. If snap
ring is not seated in the groove on mainshaft rear bearing,
remove transaxle case and repeat the procedure from step d.
k.
Tighten transaxle case mounting bolts to the specified torque.
l.
Shift the shift lever (outer)
to neutral position.
NOTE:
The neutral position is attained when shift lever (outer) is in the
position shown in the figure.
27. Install bore plug to transaxle case using the drift (A) (SST:
ST33061000).
CAUTION:
Never reuse bore plug.
28. Install select lever to transaxle case and then install retaining pin
to select lever.
CAUTION:
• Never reuse retaining pin.
• Assemble retaining pin from the direction shown by the
arrow in the figure until it becomes flush with the end sur-
face of select lever.
PCIB1923E
PCIB1838E
PCIB1930E
JSDIA6492ZZ
PCIB1837E
TRANSAXLE ASSEMBLY
TM-145
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
29. Install guide bolt, as per the following procedure.
a.
Shift the shift lever (outer) and select lever to neutral position.
b.
Visually confirm from the guide bolt mounting hole
that the
lever is securely set to neutral position. If it is not in the neutral
position, repeat the procedure from step a.
CAUTION:
The guide bolt
may damage striking rod by running into
outer-groove points, if guide bolt is tightened in the state of
(B) shown in the figure.
c.
Check continuity between terminals of neutral position switch to
confirm it in the neutral position. If it is not in the neutral position,
repeat the procedure from step a. Refer to
d.
Install guide bolt to transaxle case and then tighten guide bolt to
the specified torque.
CAUTION:
Never reuse guide bolt.
30. Apply recommended sealant to threads of neutral position
switch
. Then install it to transaxle case and tighten to the
specified torque.
• For sealant to use, refer to
CAUTION:
Remove old sealant and oil adhering to threads.
: Neutral position
: Except neutral position
: Groove of striking rod
PCIB1890E
PCIB1836E
JSDIA6484ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст