Nissan GT-R (2007-2014 year). EXHAUST SYSTEM / EXTERIOR LIGHTING SYSTEM. Service Manual — part 4
EXL-46
< REMOVAL AND INSTALLATION >
[XENON TYPE]
FRONT COMBINATION LAMP
1.
Remove front bumper fascia. Refer to
2.
Remove the headlamp mounting bolts.
3.
Remove the harness clip (A) and the washer tube (B)*.
*: Left side only
4.
Pull out the headlamp assembly forward the vehicle.
5.
Disconnect the connector before removing the headlamp hous-
ing assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• After installation, perform aiming adjustment. Refer to
• After installation, check that headlamp lighting. Refer to
EXL-48, "Inspection After Installation (HID
.
• When the front combination lamp on one side is replaced, and rubber seal is not installed to the front
combination lamp on the side that is not replaced, install a rubber seal to the front combination lamp
that is not replaced as per the following procedure.
• Always clean the front combination lamp surface where rubber seal is affixed.
1.
Align rubber seal (1) with lens inner protrusion (A) and affix so that there is not gap.
2.
Align rubber seal edge (1) with hood seal assembly edge (2) and affix under hood seal assembly.
JPLIA1163ZZ
NNLIB0019ZZ
Revision: 2012 November
2014 GT-R
FRONT COMBINATION LAMP
EXL-47
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
3.
Align rubber seal end (1) with hood end (3) and affix so that it does not protrude from hood.
Replacement
INFOID:0000000009160381
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, ,moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB (LO)
1.
Remove the front tire. Refer to
.
2.
Remove the fender protector. Keep a service area. Refer to
EXT-29, "FENDER PROTECTOR : Exploded
.
3.
Rotate the resin cap counterclockwise and unlock it.
4.
Rotate the bulb socket counterclockwise and unlock it.
5.
Remove the retaining spring lock. Remove the bulb from the headlamp housing assembly.
CAUTION:
Never break the xenon bulb ceramic tube when replacing the bulb.
HEADLAMP BULB (HI)
1.
Remove the front tire. Refer to
.
2.
Remove the fender protector. Keep a service area. Refer to
EXT-29, "FENDER PROTECTOR : Exploded
.
3.
Remove the washer tank inlet. Refer to
*: When replace a left.
4.
Rotate the resin cap counterclockwise and unlock it.
5.
Disconnect the headlamp bulb (HI) connector.
NNLIB0020ZZ
Revision: 2012 November
2014 GT-R
EXL-48
< REMOVAL AND INSTALLATION >
[XENON TYPE]
FRONT COMBINATION LAMP
6.
Rotate the bulb socket counterclockwise and unlock it.
7.
Remove the bulb from the headlamp housing assembly.
PARKING LAMP BULB
1.
Rotate the bulb socket counterclockwise and unlock it.
2.
Remove the bulb from the bulb socket.
FRONT TURN SIGNAL LAMP BULB
1.
Remove the front tire. Refer to
.
2.
Remove the fender protector. Keep a service area. Refer to
EXT-29, "FENDER PROTECTOR : Exploded
.
3.
Rotate the bulb socket counterclockwise and unlock it.
4.
Remove the bulb from the bulb socket.
Disassembly and Assembly
INFOID:0000000009160382
DISASSEMBLY
1.
Rotate the resin cap counterclockwise and unlock it.
2.
Rotate the xenon bulb socket counterclockwise and unlock it.
3.
Remove the retaining spring lock. And then remove the xenon bulb.
4.
Remove the HID control unit installation screw.
5.
Remove the HID control unit harness installation screw. And then disconnect the connector from
HID control unit.
6.
Pull out the xenon bulb socket from the headlamp housing assembly.
7.
Rotate the resin cap counterclockwise and unlock it.
8.
Disconnect the headlamp (HI) connector.
9.
Rotate the halogen bulb socket counterclockwise and unlock it.
10. Remove the halogen bulb socket from the headlamp housing assembly.
11. Rotate the parking lamp bulb socket counterclockwise and unlock it.
12. Remove the bulb from the parking lamp bulb socket.
13. Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
14. Remove the bulb from the front turn signal lamp bulb socket.
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION:
• Install HID control unit securely.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Seal packing cannot be reused.
• After installation, check that headlamp lighting. Refer to
EXL-48, "Inspection After Installation (HID
.
Inspection After Installation (HID Control Unit)
INFOID:0000000009160383
CAUTION:
Temporarily install the headlamp on the vehicle. Connect the battery to the connector (vehicle side)
when checking ON/OFF status.
XENON HEADLAMP LIGHTING CHECK
When recycled HID control unit, check the following, when there is abnormality replace the HID control unit.
1.
Xenon bulb is cold condition (turn OFF more than 10 minutes), and repetition does headlamp turned ON/
OFF, check that a headlamp illuminated it surely.
2.
Headlamp is turn ON until the xenon bulb becomes stable condition (for about 5 minutes) from cold condi-
tion, check that there are not on and off light, abnormality such as blinking.
3.
Xenon bulb is warm condition (turn ON more than 15 minutes and turn OFF for 1 minute), and repetition
does headlamp turned ON/OFF, check that a headlamp illuminated it surely.
Revision: 2012 November
2014 GT-R
FRONT COMBINATION LAMP
EXL-49
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
4.
Headlamp is turn ON for about 30 minutes, check that there are not on and off light, abnormality such as
blinking whether brightness of right and left does not have a difference.
Revision: 2012 November
2014 GT-R
EXL-50
< REMOVAL AND INSTALLATION >
[XENON TYPE]
DAYTIME RUNNING LIGHT
DAYTIME RUNNING LIGHT
Exploded View
INFOID:0000000009160384
Removal and Installation
INFOID:0000000009160385
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
Left side
1.
EXT-36, "ENGINE UNDER COVER : Removal and Installation"
2.
Remove washer tank mounting bolt, and then keep a service area.
3.
Disconnect daytime running light harness connector.
4.
Remove daytime running light mounting bolt and nut, and then remove daytime running light bracket.
5.
Move daytime running light (1) until it contacts bumper fascia rib
portion (A).
1.
Bumper fascia
2.
Daytime running light
3.
U nut
4.
Daytime running light bracket A
5.
Daytime running light bracket B
JMLIA1867ZZ
JMLIA1918ZZ
Revision: 2012 November
2014 GT-R
DAYTIME RUNNING LIGHT
EXL-51
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
6.
Rotate daytime running light around center of rib portion and
remove LED hyper day light.
Right side
1.
Remove bumper fascia. Refer to
EXT-15, "Removal and Installation"
.
2.
Remove daytime running light mounting bolt and nut, and then remove daytime running light bracket.
3.
Move daytime running light (1) until it contacts bumper fascia rib
portion (A).
4.
Rotate daytime running light around center of rib portion and
remove LED hyper day light.
INSTALLATION
Install in the reverse order of removal.
JMLIA1919ZZ
JMLIA1918ZZ
JMLIA1919ZZ
Revision: 2012 November
2014 GT-R
EXL-52
< REMOVAL AND INSTALLATION >
[XENON TYPE]
FRONT SIDE MARKER LAMP
FRONT SIDE MARKER LAMP
Exploded View
INFOID:0000000009160386
Removal and Installation
INFOID:0000000009160387
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Insert any appropriate tool (A) into the gap between the side turn
signal lamp and fender protector.
2.
Pull the side turn signal lamp toward vehicle outside while push-
ing metal clip (B) toward vehicle front, and then remove side turn
signal lamp from vehicle.
3.
Disconnect the side turn signal lamp connector.Remove the side turn signal lamp.
NOTE:
Support the vehicle-side harness of the side turn signal lamp with tape so that it does not drop inside the front
fender.
INSTALLATION
1.
Connect the side turn signal lamp connector.
2.
Fix the pawl side. And then push the clip side.
Replacement
INFOID:0000000009160388
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT SIDE MARKER LAMP BULB
1.
Front side marker lamp
JPLIA1330ZZ
: Vehicle front
NNLIB0018ZZ
Revision: 2012 November
2014 GT-R
FRONT SIDE MARKER LAMP
EXL-53
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
1.
Remove the front side marker lamp. Refer to
2.
Turn the bulb socket (1) counterclockwise and unlock it.
3.
Remove the bulb (2) from the socket.
NNLIA0025ZZ
Revision: 2012 November
2014 GT-R
EXL-54
< REMOVAL AND INSTALLATION >
[XENON TYPE]
LIGHTING & TURN SIGNAL SWITCH
LIGHTING & TURN SIGNAL SWITCH
Exploded View
INFOID:0000000009160389
The lighting & turn signal switch is integrated in the combination switch.
Revision: 2012 November
2014 GT-R
HAZARD SWITCH
EXL-55
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HAZARD SWITCH
Exploded View
INFOID:0000000009160390
The hazard switch is integrated in the set-up switch. Refer to
.
Revision: 2012 November
2014 GT-R
EXL-56
< REMOVAL AND INSTALLATION >
[XENON TYPE]
REAR COMBINATION LAMP
REAR COMBINATION LAMP
Exploded View
INFOID:0000000009160391
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000009160392
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the fascia rear bumper center. Refer to
2.
Remove the rear bumper fascia. Refer to
3.
Remove the rear combination lamp mounting bolts.
4.
Disconnect the rear side marker lamp connector.
5.
Remove the rear combination lamp.
INSTALLATION
1.
Rear combination lamp assembly
NNLIA0013ZZ
1.
Rear combination lamp
2.
Back-up lamp bulb
3.
Back-up lamp bulb socket
4.
Rear turn signal lamp bulb socket
5.
Rear turn signal lamp bulb
NNLIA0079ZZ
Revision: 2012 November
2014 GT-R
REAR COMBINATION LAMP
EXL-57
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Install in the reverse order of removal.
Replacement
INFOID:0000000009160393
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
REAR TURN SIGNAL LAMP BULB
1.
Remove the trunk lid finisher. Refer to
INT-29, "Removal and Installation"
2.
Remove the rubber cover (1).
3.
Turn the rear turn signal lamp bulb socket (2) counterclockwise
and unlock it.
4.
Remove the bulb (3) from the rear turn signal lamp bulb socket.
BACK-UP LAMP BULB
1.
Remove the trunk lid finisher. Refer to
INT-29, "Removal and Installation"
2.
Remove the rubber cover (1).
3.
Turn the back-up lamp bulb socket (2) counterclockwise and
unlock it.
4.
Remove the bulb (3) from the back-up lamp bulb socket.
NNLIA0016ZZ
NNLIA0015ZZ
Revision: 2012 November
2014 GT-R
EXL-58
< REMOVAL AND INSTALLATION >
[XENON TYPE]
REAR SIDE MARKER LAMP
REAR SIDE MARKER LAMP
Exploded View
INFOID:0000000009160394
Removal and Installation
INFOID:0000000009160395
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
1.
Remove the rear bumper fascia. Refer to
2.
Disconnect the rear side marker lamp connector.
3.
Remove the rear side marker lamp mounting bolts and clip.
4.
Remove the rear side marker lamp.
INSTALLATION
Install in the reverse order of removal.
1.
Rear side marker lamp
JPLIA1160ZZ
Revision: 2012 November
2014 GT-R
HIGH-MOUNTED STOP LAMP
EXL-59
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HIGH-MOUNTED STOP LAMP
Exploded View
INFOID:0000000009160396
Removal and Installation
INFOID:0000000009160397
REMOVAL
CAUTION:
Disconnect the battery negative terminal or the remove the fuse.
1.
Remove the rear wing. Refer to
.
2.
Remove the center leg bracket.
3.
Remove the high-mounted stop lamp mounting screw. And then
cut the two-sided tape by the any appropriate tool (A).
4.
Disconnect the connector. And then remove the high-mounted
stop lamp from the rear wing.
INSTALLATION
Install in the reverse order of removal.
1.
Rear wing
2.
High-mounted stop lamp
3.
Center leg bracket
NNLIA0017ZZ
NNLIA0018ZZ
Revision: 2012 November
2014 GT-R
EXL-60
< REMOVAL AND INSTALLATION >
[XENON TYPE]
LICENSE PLATE LAMP
LICENSE PLATE LAMP
Exploded View
INFOID:0000000009160398
Removal and Installation
INFOID:0000000009160399
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the license plate lamp in numerical order shown in the
figure.
2.
Disconnect the connector.
3.
Remove license plate lamp.
INSTALLATION
1.
Connect the connector.
2.
Fix the pawl side. And then push the resin clip side.
Replacement
INFOID:0000000009160400
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB
1.
Remove license plate lamp. Refer to
.
1.
License plate lamp
NNLIA0026ZZ
JPLIA0056ZZ
Revision: 2012 November
2014 GT-R
LICENSE PLATE LAMP
EXL-61
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
2.
Turn the bulb socket (1) counterclockwise and unlock it.
3.
Remove the bulb (2) from the socket.
JPLIA0055ZZ
Revision: 2012 November
2014 GT-R
EXL-62
< REMOVAL AND INSTALLATION >
[XENON TYPE]
REAR FOG LAMP
REAR FOG LAMP
Exploded View
INFOID:0000000009160401
REMOVAL
Removal and Installation
INFOID:0000000009160402
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1.
Remove rear fog lamp mounting bolts from rear diffuser under side.
2.
Pull out rear fog lamp to vehicle rear, and then disconnect harness connector.
3.
Remove rear fog lamp.
INSTALLATION
Installation is the reverse order of removal.
1.
Rear bumper fascia
2.
Rear fog lamp assembly
JMLIA1868ZZ
Revision: 2012 November
2014 GT-R
SERVICE DATA AND SPECIFICATIONS (SDS)
EXL-63
< SERVICE DATA AND SPECIFICATIONS (SDS)
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb Specifications
INFOID:0000000009160403
Item
Type
Wattage (W)
Front combination lamp
Headlamp (LO)
D2S (Xenon)
35
Headlamp (HI)
H9
65
Parking lamp
W5W
5
Front turn signal lamp
7444NA
28
Daytime running light
LED
—
Front side marker lamp
W5W
5
Rear combination lamp
Stop lamp
LED
—
Tail lamp
LED
—
Rear turn signal lamp
WY21W (Amber)
21
Back-up lamp
W16W
16
Rear side marker lamp
LED
—
License plate lamp
W5W
5
High-mounted stop lamp
LED
—
Rear fog lamp
LED
—
Revision: 2012 November
2014 GT-R
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст