Nissan Terrano r20e. Manual — part 401
14. Tighten side bearing cap bolts.
: 83 - 103 N
⋅
m (8.5 - 10.5 kg-m, 62 - 76 ft-lb)
15. Install side lock finger in place to prevent rotation during opera-
tion.
16. Check runout of ring gear with a dial indicator.
Runout limit:
0.08 mm (0.0031 in)
I
If backlash varies excessively in different places, the variance
may have resulted from foreign matter caught between the ring
gear and the differential case.
I
If the backlash varies greatly when the runout of the ring gear
is within a specified range, the hypoid gear set or differential
case should be replaced.
17. Check tooth contact. (Refer to PD-49.)
SPD698
SPD247
ASSEMBLY (H233B)
Differential Carrier (Cont’d)
PD-56
Propeller Shaft
GENERAL SPECIFICATIONS
Unit: mm (in)
MODEL
ALL
H/T
WAGON
Portion
Front
Rear
Propeller shaft
model
0F71H
2S80B
Number of joints
2
Coupling
method with
transmission
Flange type
Sleeve type
Types of journal
bearings
Solid type (dis-
assembly type)
Solid type
Shaft length
(Spider to spi-
der)
mm (in)
542 (21.34)
725 (28.54)
925 (36.42)
Shaft outer
diameter mm (in)
65 (2.56)
65 (2.56)
INSPECTION AND ADJUSTMENT
Front propeller shaft
Unit: mm (in)
Propeller shaft model
0F71H
Journal axial play limit
0.02 (0.0008)
Propeller shaft runout limit
0.6 (0.024)
Measuring point A
126 (4.96)
SPD996
Rear propeller shaft
Unit: mm (in)
Propeller shaft model
2S80B
Journal axial play limit
0.02 (0.0008)
Propeller shaft runout limit
0.6 (0.024)
Measuring point
A
280 (11.02)
B
475 (18.70)
C
280 (11.02)
NPD004
Available snap rings
0F71H models
Unit: mm (in)
Thickness mm (in)
ID color
Part number
1.99 (0.0783)
White
37146-01G00
2.02 (0.0795)
Yellow
37147-01G00
2.05 (0.0807)
Red
37148-01G00
2.08 (0.0819)
Green
37149-01G00
2.11 (0.0831)
Blue
37150-01G00
2.14 (0.0843)
Light brown
37151-01G00
2.17 (0.0854)
Pink
37152-01G00
2.20 (0.0866)
No paint
37153-01G00
2S80B models
Thickness mm (in)
ID color
Part number
1.99 (0.0783)
White
37146-C9400
2.02 (0.0795)
Yellow
37147-C9400
2.05 (0.0807)
Red
37148-C9400
2.08 (0.0819)
Green
37149-C9400
2.11 (0.0831)
Blue
37150-C9400
2.14 (0.0843)
Light Brown
37151-C9400
2.17 (0.0854)
Pink
37152-C9400
2.20 (0.0866)
No paint
37153-C9400
SERVICE DATA AND SPECIFICATIONS (SDS)
PD-57
Final Drive
GENERAL SPECIFICATIONS
Front final drive
R180A
4-pinion
Oil capacity (Approx.)
(Imp pt)
1.3 (2-1/4)
Rear final drive
H233B
LSD* 4-pinion
Oil capacity (Approx.)
(Imp pt)
2.8 (4-7/8)
Gear ratio
4.375
Number of teeth
Ring gear
35
Drive pinion
8
* Limited Slip Differential
INSPECTION AND ADJUSTMENT (R180A)
Ring gear runout
Ring gear runout limit
mm (in)
0.05 (0.0020)
Axle bearing adjustment
Axle bearing end play
mm (in)
0 - 0.1 (0 - 0.004)
Available axle bearing adjusting shims
Thickness mm (in)
Part number
0.10 (0.0039)
38233-01G11
0.20 (0.0079)
38233-01G12
0.30 (0.0118)
38233-01G13
0.40 (0.0157)
38233-01G14
Side gear adjustment
Side gear backlash
(Clearance between side gear to
differential case)
mm (in)
0.10 - 0.20
(0.0039 - 0.0079)
Available side gear thrust washers
Thickness mm (in)
Part number
0.75 (0.0295)
38424-W2010
0.78 (0.0307)
38424-W2011
0.81 (0.0319)
38424-W2012
0.84 (0.0331)
38424-W2013
0.87 (0.0343)
38424-W2014
0.90 (0.0354)
38424-W2015
0.93 (0.0366)
38424-W2016
0.96 (0.0378)
38424-W2017
Drive pinion height adjustment
Available pinion height adjusting washers
Thickness mm (in)
Part number
3.09 (0.1217)
38154-P6017
3.12 (0.1228)
38154-P6018
3.15 (0.1240)
38154-P6019
3.18 (0.1252)
38154-P6020
3.21 (0.1264)
38154-P6021
3.24 (0.1276)
38154-P6022
3.27 (0.1287)
38154-P6023
3.30 (0.1299)
38154-P6024
3.33 (0.1311)
38154-P6025
3.36 (0.1323)
38154-P6026
3.39 (0.1335)
38154-P6027
3.42 (0.1346)
38154-P6028
3.45 (0.1358)
38154-P6029
3.48 (0.1370)
38154-P6030
3.51 (0.1382)
38154-P6031
3.54 (0.1394)
38154-P6032
3.57 (0.1406)
38154-P6033
3.60 (0.1417)
38154-P6034
3.63 (0.1429)
38154-P6035
3.66 (0.1441)
38154-P6036
Drive pinion preload adjustment
Drive pinion bearing preload
adjusting method
Adjusting washer and spacer
Drive pinion preload
N
⋅
m (kg-cm, in-lb)
With front oil seal
1.1 - 1.7 (11 - 17, 9.5 - 14.8)
Available drive pinion preload adjusting washers
Thickness mm (in)
Part number
6.59 (0.2594)
38127-01G00
6.57 (0.2587)
38127-01G01
6.55 (0.2579)
38127-01G02
6.53 (0.2571)
38127-01G03
6.51 (0.2563)
38127-01G04
6.49 (0.2555)
38127-01G05
6.47 (0.2547)
38127-01G06
6.45 (0.2539)
38127-01G07
6.43 (0.2531)
38127-01G08
6.41 (0.2524)
38127-01G09
6.39 (0.2516)
38127-01G10
6.37 (0.2508)
38127-01G11
6.35 (0.2500)
38127-01G12
6.33 (0.2492)
38127-01G13
6.31 (0.2484)
38127-01G14
Available drive pinion preload adjusting spacers
Length mm (in)
Part number
52.20 (2.0551)
38130-G2300
52.40 (2.0630)
38131-G2301
52.60 (2.0709)
38132-G2302
52.80 (2.0787)
38133-G2303
53.00 (2.0866)
38134-G2304
53.20 (2.0945)
38135-G2305
SERVICE DATA AND SPECIFICATIONS (SDS)
PD-58
Side bearing adjustment
Differential carrier assembly turning
resistance
N (kg, lb)
34.3 - 39.2
(3.5 - 4.0, 7.7 - 8.8)
Side bearing adjusting method
Adjusting shim
Available side retainer adjusting shims
Thickness mm (in)
Part number
0.20 (0.0079)
38453-01G00
0.25 (0.0098)
38453-01G01
0.30 (0.0118)
38453-01G02
0.40 (0.0157)
38453-01G03
0.50 (0.0197)
38453-01G04
Total preload adjustment
Total preload
N
⋅
m (kg-cm, in-lb)
1.2 - 2.3 (12 - 23, 8.7 - 20.0)
Ring gear backlash
mm (in)
0.13 - 0.18 (0.0051 - 0.0071)
INSPECTION AND ADJUSTMENT (H233B)
Ring gear runout
Ring gear runout limit
mm (in)
0.08 (0.0031)
Differential torque adjustment
Differential torque
N
⋅
m (kg-m, ft-lb)
353 - 392
(36 - 40, 260 - 289)
Number of discs and plates
Friction disc
5
Friction plate
6
Spring disc
1
Spring plate
1
Wear limit of plate and disc
mm (in)
0.1 (0.004)
Allowable warpage of friction disc
and plate
mm (in)
0.05 - 0.15 (0.0020 - 0.0059)
Available discs and plates
Part name
Thickness mm (in)
Part number
Friction disc
1.48 - 1.52
(0.0583 - 0.0598)
38433-C6000
1.58 - 1.62
(0.0622 - 0.0638)
38433-C6001
Friction plate
1.48 - 1.52
(0.0583 - 0.0598)
38432-C6000
Spring disc
1.48 - 1.52
(0.0583 - 0.0598)
38436-C6000
Spring plate
1.48 - 1.52
(0.0583 - 0.0598)
38435-C6010
Drive pinion height adjustment
Available pinion height adjusting washers
Thickness mm (in)
Part number
2.58 (0.1016)
38151-01J00
2.61 (0.1028)
38151-01J01
2.64 (0.1039)
38151-01J02
2.67 (0.1051)
38151-01J03
2.70 (0.1063)
38151-01J04
2.73 (0.1075)
38151-01J05
2.76 (0.1087)
38151-01J06
2.79 (0.1098)
38151-01J07
2.82 (0.1110)
38151-01J08
2.85 (0.1122)
38151-01J09
2.88 (0.1134)
38151-01J10
2.91 (0.1146)
38151-01J11
2.94 (0.1157)
38151-01J12
2.97 (0.1169)
38151-01J13
3.00 (0.1181)
38151-01J14
3.03 (0.1193)
38151-01J15
3.06 (0.1205)
38151-01J16
3.09 (0.1217)
38151-01J17
3.12 (0.1228)
38151-01J18
3.15 (0.1240)
38151-01J19
3.18 (0.1252)
38151-01J60
3.21 (0.1264)
38151-01J61
3.24 (0.1276)
38151-01J62
3.27 (0.1287)
38151-01J63
3.30 (0.1299)
38151-01J64
3.33 (0.1311)
38151-01J65
3.36 (0.1323)
38151-01J66
3.39 (0.1335)
38151-01J67
3.42 (0.1346)
38151-01J68
3.45 (0.1358)
38151-01J69
3.48 (0.1370)
38151-01J70
3.51 (0.1382)
38151-01J71
3.54 (0.1394)
38151-01J72
3.57 (0.1406)
38151-01J73
3.60 (0.1417)
38151-01J74
3.63 (0.1429)
38151-01J75
3.66 (0.1441)
38151-01J76
SERVICE DATA AND SPECIFICATIONS (SDS)
Final Drive (Cont’d)
PD-59
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст