Nissan Terrano r20e. Manual — part 402
Drive pinion preload adjustment
Drive pinion bearing preload adjusting
method
Adjusting shim and spacer
Drive pinion preload
N
⋅
m (kg-cm, in-lb)
1.4 - 1.7 (14 - 17, 12 - 15)
Without front oil seal
1.2 - 1.5 (12 - 15, 10 - 13)
Available drive pinion preload adjusting shims
Thickness mm (in)
Part number
2.31 (0.0909)
38125-82100
2.33 (0.0917)
38126-82100
2.35 (0.0925)
38127-82100
2.37 (0.0933)
38128-82100
2.39 (0.0941)
38129-82100
2.41 (0.0949)
38130-82100
2.43 (0.0957)
38131-82100
2.45 (0.0965)
38132-82100
2.47 (0.0972)
38133-82100
2.49 (0.0980)
38134-82100
2.51 (0.0988)
38135-82100
2.53 (0.0996)
38136-82100
2.55 (0.1004)
38137-82100
2.57 (0.1012)
38138-82100
2.59 (0.1020)
38139-82100
Available drive pinion preload adjusting spacers
Length mm (in)
Part number
4.50 (0.1772)
38165-76000
4.75 (0.1870)
38166-76000
5.00 (0.1969)
38167-76000
5.25 (0.2067)
38166-01J00
5.50 (0.2165)
38166-01J10
Total preload adjustment
Total preload
N
⋅
m (kg-cm, in-lb)
1.7 - 2.5 (17 - 25, 15 - 22)
Ring gear backlash
mm (in)
0.15 - 0.20 (0.0059 - 0.0079)
Side bearing adjusting method
Side adjuster
SERVICE DATA AND SPECIFICATIONS (SDS)
Final Drive (Cont’d)
PD-60
REAR AXLE &
REAR SUSPENSION
CONTENTS
Precautions . . . . . . . . . . . . . . . . ..2
Preparation . . . . . . . . . . . . . . . . ..2
. . . . . . 4
. . . . . . . . . . ..5
Rear Axle and Rear Suspension Parts . . . . . ...5
Rear Wheel Bearing . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . .6
Components. . . . . . . . . . . . . . . . .6
Removal. . . . . . . . . . . . . . . . . ...7
Inspection. . . . . . . . . . . . . . . . . .8
Installation. . . . . . . . . . . . . . . . . 9
Removal and Installation . . . . . . . . . . ...12
. . . . . . . . . . . . . .13
Components. . . . . . . . . . . . . . . ...13
Coil Spring Shock Absorber . . . . . . . . . ..14
Upper Link, Lower Link and Panhard Rod. . . . 14
Stabilizer Bar . . . . . . . . . . . . . . . .15
SERVICE DATA AND SPECIFICATIONS (SDS)
. . ..16
General Specifications. . . . . . . . . . . ...16
Inspection and Adjustment . . . . . . . . . . 16
Precautions
I
When installing each rubber part, final tightening must be car-
ried out under unladen condition* with tires on ground.
*
Fuel, radiator coolant and engine oil full. Spare tire, jack,
hand tools and mats in designated positions.
I
Use Tool when removing or installing brake tubes.
I
If suspension or suspension parts are dismounted, check wheel
alignment and adjust if necessary.
I
Do not jack up vehicle at lower link.
Preparation
SPECIAL SERVICE TOOLS
*: Special tool or commercial equivalent
Tool number
Tool name
Description
GG94310000*
Flare nut torque wrench
Removing or installing brake piping
KV40101000*
Axle stand
Removing rear axle shaft
ST36230000*
Sliding hammer
Removing rear axle shaft
ST38020000
Bearing lock nut wrench
Removing wheel bearing lock nut
KV401-06700-B
Rear axle shaft bearing
puller
Remove wheel bearing and ABS rotor
NI-110
Rear axle shaft guide
Installing rear axle shaft
SBR820B
PRECAUTIONS AND PREPARATION
RA-2
Tool number
Tool name
Description
NI-104
Rear axle bearing
removal installation kit
Install and remove rear wheel bearing and
shaft
PRECAUTIONS AND PREPARATION
Preparation (Cont’d)
RA-3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст