Nissan Titan. Manual — part 14
BR-46
< UNIT DISASSEMBLY AND ASSEMBLY >
REAR DISC BRAKE
4. Install the piston (1) into the cylinder body and insert the piston
boot (2) side lip into piston grooves as shown.
CAUTION:
Press piston evenly and vary the pressing point to prevent
cylinder body inner wall from being rubbed.
5. Apply rubber grease to sliding sleeves, then install sliding boots and sleeves to cylinder body.
JPFIA0041ZZ
SERVICE DATA AND SPECIFICATIONS (SDS)
BR-47
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000009883564
Unit: mm (in)
Brake Pedal
INFOID:0000000009883565
STANDARD PEDAL
Unit: mm (in)
ADJUSTABLE PEDAL
Front brake
Rotor outer diameter
× thickness
350
× 30 (13.78 × 1.18)
Pad Length
× width × thickness
152
× 56.5 × 12.0 (5.98 × 2.22 × 0.47)
Cylinder bore diameter (each)
2 x 50.8 (2.00)
Rear brake
Rotor outer diameter
× thickness
320
× 14 (12.6 × 0.55)
Pad Length
× width × thickness
114
× 36.5 × 12.0 (4.49 × 1.44 × 0.47)
Cylinder bore diameter
48 (1.89)
Control valve
Valve model
Electric brake force distribution
Brake booster
Booster model
9/10 inch active booster
Recommended brake fluid
MA-15, "FOR NORTH AMERICA : Fluids and Lubri-
(Mexico).
Free height (H)
182.3 +10/-0 (7.18 +0.39/-0)
Pedal full stroke (S)
152.3 (6.00)
Clearance between brake pedal bracket and the threaded end of stop lamp switch (C1) and
ASCD cancel switch [if equipped] (C
2
)
0.74
− 1.96 (0.03 − 0.08)
AWFIA0557ZZ
BR-48
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Unit: mm (in)
CAUTION:
When equipped with adjustable pedal, the pedal must be in the forward most position (closest to the floor) for pedal height
adjustment.
Brake Booster
INFOID:0000000009883566
Unit: mm (in)
Pedal free height (H) with pedal in forward most position
182.3 +10/-0 (7.18 +0.39/-0)
Pedal full stroke (T)
153.3 (6.04)
Stop lamp switch and ASCD cancel switch threaded end to brake pedal bracket gap
0.74 - 1.96 (0.03 - 0.08)
ALFIA0149ZZ
Output rod length [at -66.7 kPa (-500 mmHg, -19.69 inHg) vacuum]
15.6 - 15.9 (0.614 - 0.626)
SBR208E
SERVICE DATA AND SPECIFICATIONS (SDS)
BR-49
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
Check Valve
INFOID:0000000009883567
Front Disc Brake
INFOID:0000000009883568
Unit: mm (in)
Rear Disc Brake
INFOID:0000000009883569
Unit: mm (in)
Input rod installation length (B)
145 - 152 (5.71 - 5.98)
WFIA0382E
Vacuum leakage
[at vacuum of – 66.7 kPa (– 500 mmHg, – 19.69 inHg)]
Within 1.3 kPa (10 mmHg, 0.39 inHg) of vacuum for 15 seconds
Brake pad
Standard thickness (new)
12.0 (0.47)
Minimum thickness
1.0 (0.04)
Disc rotor
Standard thickness (new)
30.0 (1.18)
Minimum thickness
28.5 (1.12)
Maximum uneven wear (measured at 8 positions)
0.015 (0.001)
Runout limit (with it attached to the vehicle)
0.03 (0.001)
Brake pad
Standard thickness (new)
12.0 (0.47)
Minimum thickness
1.0 (0.04)
Disc rotor
Standard thickness (new)
14.0 (0.55)
Minimum Thickness
12.5 (0.47)
Maximum uneven wear (measured at 8 positions)
0.015 (0.001)
Runout limit (with it attached to the vehicle)
0.05 (0.002)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст