Nissan Titan. Manual — part 248
P0442 EVAP CONTROL SYSTEM
EC-293
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
1. Remove EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor
attached.
2. Does water drain from the EVAP canister?
Yes or No
Yes
>> GO TO 11.
No (With CONSULT)>>GO TO 13.
No (Without CONSULT)>>GO TO 14.
11.
CHECK EVAP CANISTER
Weigh the EVAP canister with the EVAP canister vent control valve and EVAP control system pressure sensor
attached.
The weight should be less than 2.5 kg (5.5 lb).
OK or NG
OK (With CONSULT)>>GO TO 13.
OK (Without CONSULT)>>GO TO 14.
NG
>> GO TO 12.
12.
DETECT MALFUNCTIONING PART
Check the following.
• EVAP canister for damage
• EVAP hose between EVAP canister and drain filter for clogging or poor connection
>> Repair hose or replace EVAP canister.
13.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION
With CONSULT
1. Disconnect vacuum hose to EVAP canister purge volume control solenoid valve at EVAP service port.
2. Start engine.
3. Perform “PURG VOL CONT/V” in “ACTIVE TEST” mode.
4. Touch “Qu” on CONSULT screen to increase “PURG VOL CONT/V” opening to 100%.
5. Check vacuum hose for vacuum when revving engine up to 2,000 rpm.
OK or NG
OK
>> GO TO 16.
NG
>> GO TO 15.
14.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION
Without CONSULT
1. Start engine and warm it up to normal operating temperature.
2. Stop engine.
3. Disconnect vacuum hose to EVAP canister purge volume control solenoid valve at EVAP service port.
4. Start engine and let it idle for at least 80 seconds.
5. Check vacuum hose for vacuum when revving engine up to 2,000 rpm.
OK or NG
OK
>> GO TO 17.
NG
>> GO TO 15.
15.
CHECK VACUUM HOSE
Check vacuum hoses for clogging or disconnection. Refer to
.
BBIA0351E
Vacuum should exist.
Vacuum should exist.
EC-294
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
P0442 EVAP CONTROL SYSTEM
OK or NG
OK
>> GO TO 16.
NG
>> Repair or reconnect the hose.
16.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
EC-303, "Component Inspection"
OK or NG
OK
>> GO TO 17.
NG
>> Replace EVAP canister purge volume control solenoid valve.
17.
CHECK FUEL TANK TEMPERATURE SENSOR
EC-257, "Component Inspection"
OK or NG
OK
>> GO TO 18.
NG
>> Replace fuel level sensor unit.
18.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
EC-315, "Component Inspection"
OK or NG
OK
>> GO TO 19.
NG
>> Replace EVAP control system pressure sensor.
19.
CHECK EVAP PURGE LINE
Check EVAP purge line (pipe, rubber tube, fuel tank and EVAP canister) for cracks or improper connection.
.
OK or NG
OK
>> GO TO 20.
NG
>> Repair or reconnect the hose.
20.
CLEAN EVAP PURGE LINE
Clean EVAP purge line (pipe and rubber tube) using air blower.
>> GO TO 21.
21.
CHECK EVAP/ORVR LINE
Check EVAP/ORVR line between EVAP canister and fuel tank for clogging, kink, looseness and improper con-
nection. For location, refer to
OK or NG
OK
>> GO TO 22.
NG
>> Repair or replace hoses and tubes.
22.
CHECK RECIRCULATION LINE
Check recirculation line between filler neck tube and fuel tank for clogging, kink, cracks, looseness and
improper connection.
OK or NG
OK
>> GO TO 23.
NG
>> Repair or replace hose, tube or filler neck tube.
23.
CHECK REFUELING EVAP VAPOR CUT VALVE
EC-477, "Component Inspection"
OK or NG
OK
>> GO TO 24.
NG
>> Replace refueling EVAP vapor cut valve with fuel tank.
24.
CHECK FUEL LEVEL SENSOR
MWI-38, "Component Inspection"
.
OK or NG
P0442 EVAP CONTROL SYSTEM
EC-295
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
OK
>> GO TO 25.
NG
>> Replace fuel level sensor unit.
25.
CHECK INTERMITTENT INCIDENT
GI-39, "How to Check Terminal"
GI-42, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000009886701
FUEL TANK VACUUM RELIEF VALVE (BUILT INTO FUEL FILLER CAP)
1. Wipe clean valve housing.
2. Check valve opening pressure and vacuum.
3. If out of specification, replace fuel filler cap as an assembly.
CAUTION:
Use only a genuine fuel filler cap as a replacement. If an incor-
rect fuel filler cap is used, the MIL may come on.
DRAIN FILTER
1. Check visually for insect nests in the drain filter air inlet.
2. Check visually for cracks or flaws in the appearance.
3. Check visually for cracks or flaws in the hose.
4. Blow air into port A and check that it flows freely out of port B.
5. Block port B.
6. Blow air into port A and check that there is no leakage.
7. If NG, replace drain filter.
SEF445Y
Pressure: 15.3 - 20.0 kPa (0.156 - 0.204 kg/cm
2
, 2.22 -
2.90 psi)
Vacuum:
−6.0 to −3.3 kPa (−0.061 to −0.034 kg/cm
2
,
−0.87 to −0.48 psi)
SEF943S
PBIB3641E
EC-296
< DTC/CIRCUIT DIAGNOSIS >
[VK56DE]
P0443 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
P0443 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Description
INFOID:0000000009886702
SYSTEM DESCRIPTION
*1: ECM determines the start signal status by the signals of engine speed and battery voltage.
*2: This signal is sent to the ECM through CAN communication line.
This system controls flow rate of fuel vapor from the EVAP canister. The opening of the vapor by-pass pas-
sage in the EVAP canister purge volume control solenoid valve changes to control the flow rate. The EVAP
canister purge volume control solenoid valve repeats ON/OFF operation according to the signal sent from the
ECM. The opening of the valve varies for optimum engine control. The optimum value stored in the ECM is
determined by considering various engine conditions. When the engine is operating, the flow rate of fuel vapor
from the EVAP canister is regulated as the air flow changes.
COMPONENT DESCRIPTION
The EVAP canister purge volume control solenoid valve uses a ON/
OFF duty to control the flow rate of fuel vapor from the EVAP canis-
ter. The EVAP canister purge volume control solenoid valve is
moved by ON/OFF pulses from the ECM. The longer the ON pulse,
the greater the amount of fuel vapor that will flow through the valve.
On Board Diagnosis Logic
INFOID:0000000009886703
Sensor
Input signal to ECM
ECM function
Actuator
Crankshaft position sensor (POS)
Camshaft position sensor (PHASE)
Engine speed*
1
EVAP canister
purge flow control
EVAP canister purge vol-
ume control solenoid valve
Mass air flow sensor
Amount of intake air
Engine coolant temperature sensor
Engine coolant temperature
Battery
Battery voltage*
1
Throttle position sensor
Throttle position
Accelerator pedal position sensor
Accelerator pedal position
Air fuel ratio (A/F) sensor 1
Density of oxygen in exhaust gas
(Mixture ratio feedback signal)
Fuel tank temperature sensor
Fuel temperature in fuel tank
Wheel sensor
Vehicle speed*
2
PBIB2057E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0443
0443
EVAP canister purge
volume control solenoid
valve
The canister purge flow is detected during the
specified driving conditions, even when EVAP
canister purge volume control solenoid valve is
completely closed.
• EVAP control system pressure sensor
• EVAP canister purge volume control so-
lenoid valve
(The valve is stuck open.)
• EVAP canister vent control valve
• Drain filter
• EVAP canister
• Hoses
(Hoses are connected incorrectly or
clogged.)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст