Nissan Titan. Manual — part 541
SR-4
< REMOVAL AND INSTALLATION >
DRIVER AIR BAG MODULE
REMOVAL AND INSTALLATION
DRIVER AIR BAG MODULE
Removal and Installation
INFOID:0000000009882844
REMOVAL
CAUTION:
• Do not attempt to repair or replace damaged direct-connect SRS component connectors. If a driver
air bag direct-connect harness connector is damaged, the spiral cable must be replaced.
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals and wait at
least three minutes.
• When servicing the SRS, do not work from directly in front of air bag module.
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes. Refer to
PG-80, "Removal and Installation"
2. Remove the side lids (LH/RH) and the bolts.
3. Lift the driver air bag module from the steering wheel.
4. Disconnect the harness connectors from the air bag and horn, then remove the driver air bag module.
• For removal/installation of the direct-connect SRS connectors, refer to
.
CAUTION:
• When servicing the SRS, do not work from directly in front of air bag module.
• Always place air bag module with pad side facing upward.
• Do not insert any foreign objects (screwdriver, etc.) into air
bag module or harness connectors.
• Do not disassemble air bag module.
• Do not use old bolts after removal; replace with new bolts.
• Do not expose the air bag module to temperatures exceeding
90
°C (194°F).
1.
Side lids (LH/RH)
2.
Driver air bag module
3.
Steering wheel
A.
Horn harness connector
B.
Steering wheel hook
C.
Inflator harness connectors
AWHIA0461ZZ
LHIA0052E
DRIVER AIR BAG MODULE
SR-5
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Replace the air bag module if it has been dropped or sus-
tained an impact.
• Do not allow oil, grease or water to come in contact with the
air bag module.
INSTALLATION
Installation is in the reverse order of removal.
• If driver air bag module is being replaced due to deployment, spiral cable must also be replaced. Refer to
SR-6, "Removal and Installation"
.
• For removal/installation of the direct-connect SRS connectors, refer to
SRC-9, "Direct-connect SRS Compo-
• After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SBF814E
SR-6
< REMOVAL AND INSTALLATION >
SPIRAL CABLE
SPIRAL CABLE
Removal and Installation
INFOID:0000000009882845
REMOVAL
CAUTION:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals and wait at
least three minutes.
• When servicing the SRS, do not work from directly in front of air bag module.
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes. Refer to
80, "Removal and Installation"
.
2. Remove the steering wheel. Refer to
ST-22, "Removal and Installation"
3. Remove the instrument lower panel LH. Refer to
IP-17, "Removal and Installation"
.
4. Remove the steering column upper and lower covers.
5. Disconnect the harness connector from the wiper washer
switch, then pinch the tabs at wiper and washer switch base and
slide switch away from steering column to remove.
AWHIA0141GB
1.
Steering wheel
2.
Lighting and turn signal switch
3.
Wiper and washer switch
4.
Spiral cable
5.
Driver air bag module harness con-
nector
6.
Steering column upper cover
7.
Steering column assembly
8.
Steering column lower cover
9.
Screw (Do not remove)
10. Screw
A.
Refer to
LHIA0034E
SPIRAL CABLE
SR-7
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
6. While pressing tabs, pull lighting and turn signal switch toward
driver door and disconnect from base.
7. Remove the screws, release the clip, and remove the spiral
cable.
CAUTION:
• Do not disassemble spiral cable.
• Do not apply lubricant to the spiral cable.
8. Disconnect the harness connectors from the spiral cable.
CAUTION:
With the steering linkage disconnected, the spiral cable may snap by turning the steering wheel
beyond the limited number of turns. The spiral cable can be turned counterclockwise about 2.5
turns from the neutral position.
9. Remove the steering angle sensor from the spiral cable. Refer to
BRC-118, "Removal and Installation"
INSTALLATION
Installation is in the reverse order of removal.
• Align spiral cable correctly when installing steering wheel. Make
sure that the spiral cable is in the neutral position. The neutral
position is detected by turning left 2.5 revolutions from the right
end position and ending with the knob at the top.
• Refer to
BRC-8, "ADJUSTMENT OF STEERING ANGLE SEN-
SOR NEUTRAL POSITION : Special Repair Requirement"
steering angle sensor adjustment.
• After the work is completed, perform self-diagnosis to make sure
no malfunction is detected. Refer to
.
CAUTION:
• The spiral cable may snap due to steering operation if the
cable is not installed in the correct position.
• With the steering linkage disconnected, the cable may snap
by turning the steering wheel beyond the limited number of
turns. The spiral cable can be turned counterclockwise about
2.5 turns from the neutral position.
LHIA0035E
LHIA0036E
WGIA0038E
PHIA0275E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст