Nissan Titan. Manual — part 540
SEC-72
< REMOVAL AND INSTALLATION >
REMOTE KEYLESS ENTRY RECEIVER
REMOTE KEYLESS ENTRY RECEIVER
Removal and Installation
INFOID:0000000009878917
REMOTE KEYLESS ENTRY RECEIVER
Removal
1. Remove the instrument lower panel RH. Refer to
IP-16, "Removal and Installation"
2. Remove the side ventilator assembly RH. Refer to
3. Remove the RKE receiver (2).
a. Disconnect the harness connector (1) from the RKE receiver.
b. Remove the RKE receiver bolt (A).
Installation
Installation is in the reverse order of removal.
ALKIA0537ZZ
SR-1
RESTRAINTS
C
D
E
F
G
I
J
K
L
M
SECTION
SR
A
B
SR
N
O
P
CONTENTS
SRS AIRBAG
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Service . . . . . . . . . . . . . . . . . ..
Occupant Classification System Precaution . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
REMOVAL AND INSTALLATION . . . .
DRIVER AIR BAG MODULE . . . . . . . ...
Removal and Installation . . . . . . . . . . ...
SPIRAL CABLE . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ...
FRONT PASSENGER AIR BAG MODULE . .
Removal and Installation . . . . . . . . . . ...
SIDE CURTAIN AIR BAG MODULE . . . .
Removal and Installation . . . . . . . . . . .
SIDE AIR BAG MODULE . . . . . . . . ..
Removal and Installation . . . . . . . . . . .
CRASH ZONE SENSOR . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
SIDE AIR BAG (SATELLITE) SENSOR . . ...
Removal and Installation . . . . . . . . . . .
FRONT SEAT BELT PRE-TENSIONER . . ...
Removal and Installation . . . . . . . . . . .
DIAGNOSIS SENSOR UNIT . . . . . . . .
Removal and Installation . . . . . . . . . . .
OCCUPANT CLASSIFICATION SYSTEM
CONTROL UNIT . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
COLLISION DIAGNOSIS . . . . . . . . ..
For Frontal Collision . . . . . . . . . . . .
SR-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009882840
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Service
INFOID:0000000009882841
• Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least three
minutes.
For approximately three minutes after the cables are removed, it is still possible for the air bag and seat belt
pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least three minutes
have passed.
• Diagnosis sensor unit must always be installed with their arrow marks “
⇐” pointing towards the front of the
vehicle for proper operation. Also check diagnosis sensor unit for cracks, deformities or rust before installa-
tion and replace as required.
• The spiral cable must be aligned with the neutral position since its rotations are limited. Do not turn steering
wheel and column after removal of steering gear.
• Handle air bag module carefully. Always place driver and front passenger air bag modules with the pad side
facing upward and seat mounted front side air bag module standing with the stud bolt side facing down.
• Conduct self-diagnosis to check entire SRS for proper function after replacing any components.
• After air bag inflates, the instrument panel assembly should be replaced if damaged.
• Always replace instrument panel pad following front passenger air bag deployment.
Occupant Classification System Precaution
INFOID:0000000009882842
Replace occupant classification system control unit and passenger front seat cushion as an assembly.
PREPARATION
SR-3
< PREPARATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009882843
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-42057-UPD)
Air bag key set
Part of kit (J-42057)
Removing and installing air bag lock
LRS210
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст