Nissan Titan. Manual — part 629
OIL PAN
TM-199
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OIL PAN
Removal and Installation
INFOID:0000000009885918
REMOVAL
1. Drain A/T fluid. Refer to
TM-174, "Changing the A/T Fluid (ATF)"
.
2. Remove oil pan (2).
a. Remove oil pan clips (1).
•
: Front
•
: Oil pan bolts
• Drain plug (3)
3. Remove oil pan gasket.
4. Check for foreign materials in oil pan to help determine cause of malfunction. If the A/T fluid is very dark,
has some burned smell, or contains foreign particles then friction material (clutches, band) may need
replacement. A tacky film that will not wipe clean indicates varnish build up. Varnish can cause valves,
servo, and clutches to stick and can inhibit pump pressure.
CAUTION:
If friction material is detected, flush the transmission cooler after repair. Refer to
5. Remove magnets from oil pan.
INSTALLATION
1. Install the oil pan magnets as shown.
AWDIA0023ZZ
SCIA5200E
SCIA5200E
TM-200
< REMOVAL AND INSTALLATION >
OIL PAN
2. Install the oil pan (2) with a new oil pan gasket.
•
: Front
•
: Oil pan bolts
• Clips (1)
• Drain plug (3)
CAUTION:
• Be sure the oil drain plug is located to the rear of the
transmission assembly.
• Before installing oil pan bolts, remove any traces of old
sealant from the sealing surfaces and threaded holes.
• Do not reuse old gasket, replace with a new one.
• Always replace the oil pan bolts as they are self-sealing.
• Partially install the oil pan bolts in a criss-cross pattern to prevent dislocation of the gasket.
3. Install oil pan bolts and clips tighten in numerical order as
shown.
4. Install drain plug with new gasket to oil pan and tighten to speci-
fication.
CAUTION:
Do not reuse drain plug gasket.
5. Refill the A/T with fluid and check for fluid leakage. Refer to
TM-172, "Checking the A/T Fluid (ATF)"
.
AWDIA0023ZZ
Oil pan bolts
: 7.9 N·m (0.81 kg-m, 70 in-lb)
Drain plug
: 34 N·m (3.5 kg-m, 25 ft-lb)
SCIA4113E
CONTROL VALVE WITH TCM
TM-201
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL VALVE WITH TCM
Control Valve with TCM
INFOID:0000000009885919
COMPONENTS
REMOVAL AND INSTALLATION OF CONTROL VALVE WITH TCM
Removal
1. Disconnect negative battery terminal.
2. Drain A/T fluid. Refer to
TM-174, "Changing the A/T Fluid (ATF)"
.
3. Disconnect A/T assembly harness connector.
1.
Transmission
2.
Snap ring
3.
Sub-harness
4.
Control valve with TCM
5.
Bracket
6.
O-ring
7.
Plug
8.
Oil pan gasket
9.
Brackets
10. Oil pan bolt
11. Oil pan
12. Magnet
13. Drain plug
14. Drain plug gasket
15. Terminal cord assembly
16. O-ring
A.
For tightening torque, refer to "Installation"
AWDIA0886GB
TM-202
< REMOVAL AND INSTALLATION >
CONTROL VALVE WITH TCM
4. Remove snap ring from A/T assembly harness connector.
5. Push A/T assembly harness connector.
CAUTION:
Do not damage connector.
6. Remove oil pan and oil pan gasket. Refer to
TM-199, "Removal and Installation"
.
7. Straighten terminal clip (
) to free the output speed sensor har-
ness.
8. Disconnect output speed sensor connector (1).
CAUTION:
Do not damage connector.
9. Remove bolts (A), (B) and (C) from control valve with TCM.
SCIA5021E
SCIA5022E
JSDIA1316ZZ
: Front
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA8074E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст