Nissan Titan. Manual — part 628
AIR BREATHER HOSE
TM-195
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
AIR BREATHER HOSE
2WD
2WD : Removal and Installation
INFOID:0000000009885916
COMPONENTS
REMOVAL
1. Release air breather hose from clip.
2. Disconnect air breather hose from transmission tube.
3. Disconnect air breather hose from air breather tube.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Install air breather hose with paint mark at upper side.
• When installing the air breather hose, do not crush or block by folding or bending the hose.
• When inserting the hose to the transmission tube, be sure to insert it fully until its end reaches the
tube bend portion.
• Make sure clip is securely installed to bracket.
4WD
4WD : Removal and Installation
INFOID:0000000009885917
COMPONENTS
A.
Set air breather hose with
paint mark at upper side
B.
Clip (set securely to bracket)
AWDIA0554GB
TM-196
< REMOVAL AND INSTALLATION >
AIR BREATHER HOSE
REMOVAL
1. Disconnect air breather hose from transfer motor.
2. Disconnect air breather hose from breather tube (transfer).
3. Disconnect air breather hose from actuator.
4. Release air breather hose clamp and clips as necessary.
5. Disconnect air breather hoses from breather tube.
CAUTION:
Note paint marks for installation.
INSTALLATION
CAUTION:
Make sure there are no pinched or restricted areas on each air breather hose caused by folding or
bending when installing it.
1. Install each air breather hose into the breather tube (4). Set
each air breather hose with paint mark facing upward.
• A/T breather hose (1)
• Transfer breather hose (2)
• Actuator/transfer motor breather hose (3)
• Paint marks (A)
1.
Breather tube
2.
Clip A
3.
Clip B
4.
Clip C
5.
Clip D
6.
Actuator
7.
Air breather hose clamp
8.
Clip E
9.
Transfer motor
10. Breather tube (transfer)
Front
AWDIA0010ZZ
ALDIA0110ZZ
AIR BREATHER HOSE
TM-197
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2. Install actuator/transfer motor air breather hose (1) and transfer
air breather hose (2) on clip (A) with the paint mark (B) facing
upward.
•
:Front
3. Install clip (B) on actuator/transfer motor air breather hose (1)
and transfer air breather hose (2) with the paint mark (A)
matched.
•
:Front
4. Install actuator/transfer motor air breather hose (1) and transfer
air breather hose (2) on clip (B) and clip (C) with the paint mark
(A) and (D) facing upward.
•
:Front
5. Install the actuator air breather hose into the actuator (case con-
nector) until the hose end reaches the base of the tube. Set
actuator air breather hose with paint mark facing leftward.
6. Install clip (B) on transfer motor air breather hose (2) and trans-
fer air breather hose (1) with the paint mark (A) matched.
•
:Front
ALDIA0111ZZ
AWDIA0011ZZ
AWDIA0012ZZ
SDIA3226E
AWDIA0013ZZ
TM-198
< REMOVAL AND INSTALLATION >
AIR BREATHER HOSE
7. Install the transfer air breather hose into the breather tube
(transfer, metal connector) until the hose end reaches the base
of the tube. Set transfer air breather hose with paint mark facing
upwards.
8. Install the transfer motor air breather hose into the transfer
motor (case connector) until the hose end reaches the end of
the curved section. Set transfer motor air breather hose with
paint mark facing leftward.
SDIA3196E
SDIA3194E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст