Nissan Titan. Manual — part 441
DOOR FINISHER
INT-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Removal
1. Remove the upper and lower seat belt anchor bolts. Refer to
SB-13, "Removal and Installation"
.
2. Release the clips and remove seat belt retractor cover.
3. Remove the armrest.
4. Remove the screws behind armrest.
5. Release the clips and remove rear door finisher.
Installation
Installation is in the reverse order of removal.
INT-14
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
BODY SIDE TRIM
Removal and Installation
INFOID:0000000009881974
KING CAB
CAUTION:
• Use a suitable tool to remove metal clips from finishers.
• When removing or installing body side welts, do not allow butyl seal to come in contact with pillar
finisher.
CREW CAB
CAUTION:
• Use a suitable tool to remove metal clips from finishers.
1.
Door welt
2.
Rear door parting seal
3.
Rear kicking plate
4.
Front kicking plate
5.
Plastic clip
6.
Lower dash side finisher
7.
Front door parting seal
8.
Front pillar assist grip
9.
Front pillar finisher
10. Rear body side welt
Pawl
Clip
AWJIA0759GB
BODY SIDE TRIM
INT-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
• When removing or installing body side welts, do not allow butyl seal to come in contact with pillar
finisher.
LOWER DASH SIDE FINISHER
Removal
1. Remove the push pin from lower dash side finisher.
2. Remove the front kicking plate.
3. Remove the lower dash side finisher and front kicking plate together.
4. Remove the lower dash side finisher from front kicking plate.
Installation
Installation is in the reverse order of removal.
1.
Center pillar upper finisher
2.
Center pillar assist grip
3.
Rear door welt
4.
Rear door parting seal
5.
Rear kicking plate
6.
Center pillar lower finisher
7.
Front kicking plate
8.
Plastic clip
9.
Lower dash side finisher
10. Front door parting seal
11. Front door welt
12. Front pillar assist grip
13. Front pillar finisher
Pawl
Clip
AWJIA0761ZZ
INT-16
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
CENTER PILLAR LOWER FINISHER
Removal
1. Remove the seat belt lower anchor. Refer to
SB-13, "Removal and Installation"
• On RH side, disconnect seat belt tension sensor.
2. Remove the front and rear kicking plates.
3. Remove the center pillar lower finisher.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR UPPER FINISHER
Removal
1. Partially remove the front and rear door welts.
2. Remove the front and rear kicking plates.
3. Remove the center pillar lower finisher.
4. Remove the D ring anchor bolt cover and anchor bolt. Refer to
SB-4, "Removal and Installation of Front
.
5. Remove the center pillar assist grip covers and bolts, then remove center pillar assist grip.
6. Remove the center pillar upper finisher.
Installation
Installation is in the reverse order of removal.
FRONT PILLAR FINISHER
Removal
1. Remove the front pillar assist grip cover(s) and bolt(s), then remove front pillar assist grip.
2. Release the clips, then remove the front pillar finisher.
Installation
Installation is in the reverse order of removal.
KICKING PLATES
Removal
Release the clips and remove the front and/or rear kicking plates.
Installation
Installation is in the reverse order of removal.
DOOR PARTING SEALS
Removal
1. Open the front and/or rear doors fully.
2. Release the clips and remove the parting seals.
Installation
Installation is in the reverse order of removal.
REAR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст