Nissan Titan. Manual — part 632
TRANSMISSION ASSEMBLY
TM-211
< UNIT REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
UNIT REMOVAL AND INSTALLATION
TRANSMISSION ASSEMBLY
Removal and Installation (2WD)
INFOID:0000000009885923
COMPONENTS
CAUTION:
• Before replacing transmission assembly, perform "ADDITIONAL SERVICE WHEN REPLACING
TRANSMISSION ASSEMBLY". Refer to
TM-9, "ADDITIONAL SERVICE WHEN REPLACING TRANS-
MISSION ASSEMBLY : Special Repair Requirement"
• When removing the A/T assembly from engine, first remove the crankshaft position sensor (POS)
from the A/T assembly. Be careful not to damage sensor edge.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Disconnect the battery negative terminal. Refer to
PG-80, "Removal and Installation"
2. Remove A/T fluid indicator.
3. Remove engine under cover using power tool. Refer to
EXT-15, "Removal and Installation"
1.
A/T fluid indicator pipe
2.
A/T fluid indicator
3.
O-ring
4.
Transmission assembly
5.
Fluid cooler tube
6.
A/T cross member
7.
Insulator
8.
Copper sealing washers
AWDIA0553GB
TM-212
< UNIT REMOVAL AND INSTALLATION >
TRANSMISSION ASSEMBLY
4. Remove crankshaft position sensor (POS) from A/T assembly.
CAUTION:
• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings or foreign material to get on the
sensor front edge magnetic area.
• Do not place in an area affected by magnetism.
5. Remove A/T fluid indicator pipe.
CAUTION:
Do not reuse O-ring.
6. Remove exhaust front tube and center muffler using power tool.
EX-5, "Removal and Installation"
7. Remove rear propeller shaft. Refer to
DLN-148, "Removal and Installation"
8. Disconnect control cable.
9. Remove A/T fluid cooler tubes from A/T assembly.
CAUTION:
Do not reuse copper sealing washers.
10. Support A/T assembly with a transmission jack.
CAUTION:
When setting the transmission jack, be careful not to allow it to collide against the drain plug.
11. Remove dust cover from converter housing.
12. Turn crankshaft to access and remove the four bolts for drive
plate and torque converter.
CAUTION:
When turning crankshaft, turn it clockwise as viewed from
the front of the engine.
13. Remove cross member using power tool.
14. Remove air breather hose. Refer to
15. Disconnect A/T assembly harness connector.
16. Remove the A/T assembly to engine bolts using power tool.
17. Remove A/T assembly from vehicle using transmission jack.
CAUTION:
• Secure torque converter to prevent it from dropping.
• Secure A/T assembly to a transmission jack.
INSPECTION
Installation and Inspection of Torque Converter
• After inserting a torque converter to a transmission, be sure to
check distance (A) to ensure it is within specifications.
LCIA0334E
LCIA0335E
SCIA0499E
Distance (A)
: 24.0 mm (0.94 in) or more
SAT017B
TRANSMISSION ASSEMBLY
TM-213
< UNIT REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
INSTALLATION
Installation is in the reverse order of removal, while paying attention to the following:
CAUTION:
Do not reuse O-ring and copper sealing washers.
• When installing transmission to the engine, attach the bolts in the
order as shown.
CAUTION:
• When replacing an engine or transmission you must make
sure the dowels are installed correctly during re-assembly.
• Improper alignment caused by missing dowels may cause
vibration, oil leaks or breakage of drivetrain components.
NOTE:
*: No.2 bolt also secures air breather tube.
• Align the positions of bolts for drive plate with those of the torque
converter, and temporarily tighten the bolts. Then tighten the bolts
with the specified torque. Refer to
TM-211, "Removal and Installa-
CAUTION:
• When turning crankshaft, turn it clockwise as viewed from
the front of the engine.
• After converter is installed to drive plate, rotate crankshaft
several turns and check to be sure that transmission rotates
freely without binding.
• Install crankshaft position sensor (POS).
• After completing installation check fluid leakage, fluid level and the
positions of A/T. Refer to
TM-172, "Checking the A/T Fluid (ATF)"
TM-190, "Inspection and Adjustment"
.
Removal and Installation (4WD)
INFOID:0000000009885924
COMPONENTS
Transmission to engine bolts : 113 N·m (12 kg-m,
83 ft-lb)
LCIA0371E
LCIA0335E
TM-214
< UNIT REMOVAL AND INSTALLATION >
TRANSMISSION ASSEMBLY
CAUTION:
• Before replacing transmission assembly, perform "ADDITIONAL SERVICE WHEN REPLACING
TRANSMISSION ASSEMBLY". Refer to
TM-9, "ADDITIONAL SERVICE WHEN REPLACING TRANS-
MISSION ASSEMBLY : Special Repair Requirement"
• When removing the A/T assembly from engine, first remove the crankshaft position sensor (POS)
from the A/T assembly. Be careful not to damage sensor edge.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Disconnect the battery negative terminal. Refer to
PG-80, "Removal and Installation"
2. Remove A/T fluid indicator.
3. Remove engine under cover using power tool. Refer to
EXT-15, "Removal and Installation"
4. Remove transfer under cover using power tool (if equipped).
5. Remove exhaust front tube and center muffler using power tool. Refer to
6. Remove propeller shafts. Refer to
DLN-130, "Removal and Installation"
7. Disconnect control cable.
1.
A/T fluid indicator pipe
2.
A/T fluid indicator
3.
O-ring
4.
Transmission assembly
5.
Fluid cooler tube
6.
Copper sealing washer
7.
A/T cross member
8.
Insulator
AWDIA0548GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст