Nissan Titan. Manual — part 631
CONTROL VALVE WITH TCM
TM-207
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
10. Tighten bolt (1A), (2B) and (3A) temporarily to prevent disloca-
tion. After that tighten them in order (1
→ 2 → 3). Then tighten
other bolts.
11. Tighten control valve with TCM bolts to the specified torque.
12. Connect output speed sensor connector (1).
13. Securely fasten output speed sensor (1) harness with terminal
clip (
).
14. Install oil pan to transmission case. Refer to
TM-199, "Removal and Installation"
.
15. Pull up A/T assembly harness connector.
CAUTION:
Do not damage connector.
: Front
Bolt symbol
A
B
C
Number of bolts
5
6
1
Length mm (in)
42 (1.65)
55 (2.17)
40 (1.57)
Tightening torque
N·m (kg-m, in-lb)
7.9 (0.81, 70)
With ATF applied
7.9 (0.81, 70)
SCIA8075E
JSDIA1319ZZ
JSDIA1316ZZ
SCIA5038E
TM-208
< REMOVAL AND INSTALLATION >
CONTROL VALVE WITH TCM
16. Install snap ring to A/T assembly harness connector.
17. Connect A/T assembly harness connector.
18. Connect the negative battery terminal.
19. Refill the A/T with fluid and check the fluid level and for fluid
leakage. Refer to
TM-172, "Checking the A/T Fluid (ATF)"
.
SCIA5039E
REAR OIL SEAL
TM-209
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REAR OIL SEAL
Removal and Installation
INFOID:0000000009885920
REMOVAL
1. Remove rear propeller shaft. Refer to
DLN-139, "Removal and Installation"
2. Remove transfer from transmission (4WD models). Refer to
TM-213, "Removal and Installation (4WD)"
.
3. Remove rear oil seal using suitable tool.
CAUTION:
Do not scratch rear extension assembly (2WD models) or
adapter case assembly (4WD models).
INSTALLATION
1. Install new rear oil seal until it is flush into the rear extension
case (2WD models) using Tool or adapter case (4WD models)
using suitable tool.
CAUTION:
• Apply ATF to rear oil seal.
• Do not reuse rear oil seal.
2. Install transfer to transmission (4WD models). Refer to
"Removal and Installation (4WD)"
.
3. Install rear propeller shaft. Refer to
.
4. Check the A/T fluid level and for fluid leakage. Refer to
"Checking the A/T Fluid (ATF)"
.
SCIA5254E
Tool number
: ST33400001 (J-26082)
WCIA0475E
TM-210
< REMOVAL AND INSTALLATION >
FLUID COOLER SYSTEM
FLUID COOLER SYSTEM
Exploded View
INFOID:0000000009885921
Fluid Cooler
Removal and Installation
INFOID:0000000009885922
REMOVAL
1. Remove the radiator. Refer to
CO-15, "Removal and Installation"
.
2. Disconnect the transmission fluid cooler hoses.
3. Remove the transmission fluid cooler.
INSTALLATION
Installation is in the reverse order of removal.
ALDIA0212GB
1.
Radiator
2.
Fluid cooler hose
3.
Fluid cooler
4.
Fluid cooler hose
5.
A/C condenser
Front
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст