Nissan Pathfinder (2011 year). Manual — part 201
DLN-146
< REMOVAL AND INSTALLATION >
[TRANSFER: ATX14B]
TRANSFER CONTROL DEVICE
TRANSFER CONTROL DEVICE
Removal and Installation
INFOID:0000000006245044
REMOVAL
CAUTION:
Change vehicle state to 2WD, and then remove and install transfer control device.
1. Remove front propeller shaft. Refer to
DLN-318, "Removal and Installation"
.
2. Disconnect transfer control device connector.
3. Remove transfer control lever.
4. Disconnect vacuum line.
5. Remove transfer control device.
INTSTALLATION
CAUTION:
Check 4WD shift indicator after installation. Refer to
DLN-130, "Precaution for Transfer Assembly and
Transfer Control Unit Replacement"
Installation is in the reverse order of removal.
1.
Shift lever
2.
Actuator
SDIA2654E
2011 Pathfinder
AIR BREATHER HOSE
DLN-147
< REMOVAL AND INSTALLATION >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000006245045
VQ40DE
REMOVAL
1. Disconnect air breather hose from transfer motor.
2. Disconnect air breather hose from breather tube (transfer).
3. Disconnect air breather hose from actuator.
4. Release air breather hose clamp and clips as necessary.
5. Disconnect air breather hoses from breather tube.
CAUTION:
Note paint marks for installation.
INSTALLATION
CAUTION:
Make sure there are no pinched or restricted areas on each air breather hose caused by folding or
bending when installing it.
1. Install each air breather hose into the breather tube (metal con-
nector) until the hose end reaches the end of the curve section.
Set each air breather hose with paint mark facing upward.
SDIA3339E
1.
Breather tube
2.
Clip A
3.
Clip B
4.
Clip C
5.
Clip D
6.
Clip E
7.
Actuator
8.
Air breather hose clamp
9.
Clip F
10. Transfer motor
11. Breather tube (transfer)
SDIA3340E
2011 Pathfinder
DLN-148
< REMOVAL AND INSTALLATION >
[TRANSFER: ATX14B]
AIR BREATHER HOSE
2. Install actuator/transfer motor air breather hose and transfer air
breather hose on clip A and clip B with the paint mark facing
upward.
3. Install clip C on actuator/transfer motor air breather hose and
transfer air breather hose with the paint mark matched.
4. Install actuator/transfer motor air breather hose and transfer air
breather hose on clip D and clip E with the paint mark facing
upward.
5. Install the actuator air breather hose into the actuator (case con-
nector) until the hose end reaches the base of the tube. Set
actuator air breather hose with paint mark facing leftward.
6. Install clip F on transfer motor air (control device) breather hose
and transfer air breather hose with the paint mark matched.
SDIA3342E
SDIA3343E
SDIA3344E
SDIA3226E
SDIA3345E
2011 Pathfinder
AIR BREATHER HOSE
DLN-149
< REMOVAL AND INSTALLATION >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
7. Install the transfer air breather hose (A) into the breather tube
(transfer, metal connector) until the hose end reaches the base
of the tube. Set transfer air breather hose with paint mark (B)
facing upwards.
8. Install the transfer motor air breather hose into the transfer
motor (case connector) until the hose end reaches the end of
the curved section. Set transfer motor air breather hose with
paint mark facing leftward.
REMOVAL AND INSTALLATION
VK56DE
REMOVAL
1. Disconnect air breather hose from transfer motor.
2. Disconnect air breather hose from breather tube (transfer).
3. Disconnect air breather hose from actuator.
4. Release air breather hose clamp and clips as necessary.
5. Disconnect air breather hoses from breather tube.
AWDIA0784ZZ
SDIA3194E
AWDIA0010ZZ
1.
Breather tube
2.
Clip A
3.
Clip B
4.
Clip C
5.
Clip D
6.
Actuator
7.
Air breather hose clamp
8.
Clip E
9.
Transfer motor
10. Breather tube (transfer)
Front
2011 Pathfinder
DLN-150
< REMOVAL AND INSTALLATION >
[TRANSFER: ATX14B]
AIR BREATHER HOSE
CAUTION:
Note paint marks for installation.
INSTALLATION
CAUTION:
Make sure there are no pinched or restricted areas on each air breather hose caused by folding or
bending when installing it.
1. Install each air breather hose into the breather tube (4). Set
each air breather hose with paint mark facing upward.
• Paint marks (A)
• A/T breather hose (1)
• Transfer air breather hose (2)
• Actuator/transfer motor air breather hose (3)
2. Install actuator/transfer motor air breather hose (1) and transfer
air breather hose (2) on clip (A) with the paint mark (B) facing
upward.
: Front
3. Install clip (A) on actuator/transfer motor air breather hose (1)
and transfer air breather hose (2) with the paint mark (B)
matched.
: Front
4. Install actuator/transfer motor air breather hose (1) and transfer
air breather hose (2) on clip (C) and clip (B) with the paint mark
(A) and (D) facing upward.
: Front
ALDIA0110ZZ
ALDIA0111ZZ
AWDIA0011ZZ
AWDIA0012ZZ
2011 Pathfinder
AIR BREATHER HOSE
DLN-151
< REMOVAL AND INSTALLATION >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
5. Install the actuator air breather hose into the actuator (case con-
nector) until the hose end reaches the base of the tube. Set
actuator air breather hose with paint mark facing leftward.
6. Install clip (A) on transfer motor air breather hose (2) and trans-
fer air breather hose (1) with the paint mark (B) matched.
: Front
7. Install the transfer air breather hose (A) into the breather tube
(transfer, metal connector) until the hose end reaches the base
of the tube. Set transfer air breather hose with paint mark (B)
facing upwards.
8. Install the transfer motor air breather hose into the transfer
motor (case connector) until the hose end reaches the end of
the curved section. Set transfer motor air breather hose with
paint mark facing leftward.
SDIA3226E
AWDIA0013ZZ
AWDIA0784ZZ
SDIA3194E
2011 Pathfinder
DLN-152
< REMOVAL AND INSTALLATION >
[TRANSFER: ATX14B]
TRANSFER MOTOR
TRANSFER MOTOR
Removal and Installation
INFOID:0000000006245046
REMOVAL
1. Disconnect the transfer motor connector.
2. Remove the transfer motor air breather hose from the transfer
motor. Refer to
DLN-147, "Removal and Installation"
3. Remove the transfer motor bolts.
4. Remove the transfer motor.
INSTALLATION
1. Apply ATF to the new O-ring and install it to the transfer motor.
CAUTION:
Do not reuse O-rings.
2. Fit the double-flat end of the transfer motor shaft into the slot of
the sub-oil pump assembly. Then tighten to the specified torque.
DLN-156, "Disassembly and Assembly"
CAUTION:
Be sure to install connector bracket.
3. Install the transfer motor air breather hose to the transfer motor.
DLN-147, "Removal and Installation"
4. Connect the transfer motor connector.
5. Check the transfer fluid. Refer to
6. Start the engine for one minute. Then stop the engine and recheck the transfer fluid. Refer to
SDIA2133E
SDIA2787E
2011 Pathfinder
TRANSFER ASSEMBLY
DLN-153
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
UNIT REMOVAL AND INSTALLATION
TRANSFER ASSEMBLY
Removal and Installation
INFOID:0000000006245047
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Set transfer state as 2WD when 4WD shift switch is at 2WD.
2. Remove the under covers using power tool.
3. Remove the center exhaust tube and main muffler. Refer to
EX-7, "Removal and Installation"
.
4. Remove the front and rear propeller shafts. Refer to
DLN-318, "Removal and Installation"
328, "Removal and Installation"
DLN-339, "Removal and Installation"
CAUTION:
Do not damage spline, sleeve yoke and rear oil seal when removing rear propeller shaft.
5. Remove the A/T nuts from the A/T crossmember. Refer to
6. Position two suitable jacks under the A/T and transfer assembly.
7. Remove the crossmember. Refer to
WARNING:
Support A/T and transfer assembly using two suitable jacks while removing crossmember.
8. Disconnect the electrical connectors from the following:
• ATP switch
• Neutral 4LO switch
• Wait detection switch
• Transfer motor
• Transfer control device
• Transfer terminal cord assembly
9. Remove transfer wiring harness.
10. Disconnect each air breather hose from the following. Refer to
DLN-147, "Removal and Installation"
• Actuator
• Breather tube (transfer)
• Transfer motor
11. Remove the transfer control device from the extension housing.
12. Remove the transfer to A/T and A/T to transfer bolts.
13. Remove the transfer assembly.
WARNING:
Support transfer assembly with suitable jack while removing it.
CAUTION:
Do not damage rear oil seal (A/T).
INSTALLATION
Installation is in the reverse order of removal.
• Tighten the bolts to specification.
• Fill the transfer with new fluid and check for fluid leakage and fluid
• Start the engine for one minute. Then stop the engine and recheck
the transfer fluid. Refer to
Transfer bolt torque
: 36 N·m (3.7 kg-m, 27 ft-lb)
SMT872C
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст