Nissan Pathfinder (2011 year). Manual — part 490
MA-44
< PERIODIC MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
5. Allow the A/T fluid temperature to fall to approximately 65
°
C (149
°
F). Use the CONSULT-III to monitor the
A/T fluid temperature as follows:
NOTE:
The A/T fluid level will be significantly affected by the A/T fluid temperature as shown. Therefore monitor
the A/T fluid temperature data using the CONSULT-III.
a. Connect CONSULT-III to data link connector.
b. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT-III.
c.
Read out the value of “ATF TEMP 1”.
6. Re-check the A/T fluid level at A/T fluid temperatures of approxi-
mately 65
°
C (149
°
F) using the “HOT” range on the A/T fluid
level gauge as shown. The HOT range is between 50
°
- 80
°
C
(122
°
- 176
°
F).
CAUTION:
• When wiping the A/T fluid from the A/T fluid level gauge,
always use lint-free paper, not a cloth.
• To check the A/T fluid level, insert the A/T fluid level
gauge until the cap contacts the top of the A/T fluid charg-
ing pipe, with the gauge reversed from the normal
inserted position as shown.
7. Check the A/T fluid condition.
• If the A/T fluid is very dark or has some burned smell, there
may be an internal problem with the transmission. Refer to
. Flush the transmission cooling system after repairing
the transmission.
• If the A/T fluid contains frictional material (clutches, bands,
etc.), replace the radiator and flush the transmission cooler
lines using cleaning solvent and compressed air after repairing
the transmission.
8. Install the A/T fluid level gauge in the A/T fluid charging pipe.
9. Tighten the A/T fluid level gauge bolt to specification.
SLIA0016E
LLIA0071E
A/T fluid level gauge bolt
: Refer to
(4WD).
SCIA2899E
2011 Pathfinder
CHASSIS AND BODY MAINTENANCE
MA-45
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
A/T FLUID : Changing the A/T Fluid (ATF)
INFOID:0000000006827715
CAUTION:
If using the vehicle for towing, the A/T fluid must be replaced as specified. Refer to
AND CANADA : Introduction to Periodic Maintenance"
(United States and Canada) or
MEXICO : Periodic Maintenance Schedule"
(Mexico).
1. Drive the vehicle to warm up the A/T fluid to approximately 80
°
C (176
°
F).
2. Stop the engine.
3. Remove the A/T fluid level gauge.
4. Drain the A/T fluid from the drain plug hole, then install the drain
plug with a new gasket. Refill the transmission with new A/T
fluid. Always refill with the same volume as the drained A/T fluid.
Use the A/T fluid level gauge to check the A/T fluid level as
shown. Add A/T fluid as necessary.
• To flush out the old A/T fluid from the transmission oil coolers, pour new A/T fluid into the A/T fluid charg-
ing pipe with the engine idling and at the same time drain the old A/T fluid from the auxiliary transmis-
sion oil cooler hose return line.
• When the color of the A/T fluid coming out of the auxiliary transmission oil cooler hose return line is
about the same as the color of the new A/T fluid, flushing out the old A/T fluid is complete. The amount
of new A/T fluid used for flushing should be 30% to 50% increase of the specified capacity.
CAUTION:
• If Genuine NISSAN Matic S ATF is not available, Genuine NISSAN Matic J ATF may also be used.
Using automatic transmission fluid other than Genuine NISSAN Matic S or Matic J will cause
deterioration in driveability. and may damage automatic transmission, which is not covered by
the NISSAN new vehicle limited warranty.
• When filling the transmission with A/T fluid, do not spill the A/T fluid on any heat generating
parts such as the exhaust manifold.
• Do not reuse the drain plug gasket.
5. Install the A/T fluid level gauge and tighten the A/T fluid level gauge bolt to specification.
6. Drive the vehicle to warm up the A/T fluid to approximately 80
°
C (176
°
F).
7. Check the fluid level and condition. If the A/T fluid is still dirty,
repeat steps 2 through 6.
Drain plug
: Refer to
LLIA0071E
A/T fluid grade and capacity
: Refer to
MA-18, "FOR USA AND CANADA : Flu-
(United States and Canada
MA-15, "FOR MEXICO : Periodic Maintenance
A/T fluid level gauge bolt
: Refer to
(4WD).
LLIA0071E
2011 Pathfinder
MA-46
< PERIODIC MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
8. Install the A/T fluid level gauge in the A/T fluid charging pipe and install the A/T fluid level gauge bolt.
9. Tighten the A/T fluid level gauge bolt to specification.
TRANSFER FLUID
TRANSFER FLUID : ATX14B
INFOID:0000000006243423
TRANSFER FLUID : Inspection
INFOID:0000000006827716
CAUTION:
If using the vehicle for towing, the transfer fluid must be replaced as specified. Refer to
USA AND CANADA : Introduction to Periodic Maintenance"
"FOR MEXICO : Periodic Maintenance Schedule"
(Mexico).
FLUID LEAKAGE AND FLUID LEVEL
1. Make sure that fluid is not leaking from the transfer assembly or around it.
2. Check fluid level from the filler plug hole as shown.
CAUTION:
Do not start engine while checking fluid level.
3. Install the filler plug with a new gasket to the transfer. Tighten to
the specified torque. Refer to
CAUTION:
Do not reuse gasket.
TRANSFER FLUID : Replacement
INFOID:0000000006827717
CAUTION:
If using the vehicle for towing, the transfer fluid must be replaced as specified. Refer to
USA AND CANADA : Introduction to Periodic Maintenance"
(United States and Canada) or
"FOR MEXICO : Periodic Maintenance Schedule"
(Mexico).
DRAINING
1. Stop engine.
2. Remove the drain plug and gasket and drain the fluid.
3. Install the drain plug with a new gasket to the transfer. Tighten to
the specified torque. Refer to
CAUTION:
Do not reuse gasket.
FILLING
A/T fluid level gauge bolt
: Refer to
(4WD).
SDIA3209E
SDIA3208E
2011 Pathfinder
CHASSIS AND BODY MAINTENANCE
MA-47
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
1. Remove the filler plug and gasket.
2. Fill the transfer with new fluid until the fluid level reaches the
specified limit near the filler plug hole.
CAUTION:
Carefully fill fluid. (Fill up for approx. 3 minutes.)
3. Leave the vehicle for 3 minutes, and check fluid level again.
4. Install the filler plug with a new gasket to the transfer. Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
TRANSFER FLUID : TX15B
INFOID:0000000006243426
TRANSFER FLUID : Inspection
INFOID:0000000006827718
CAUTION:
If using the vehicle for towing, the transfer fluid must be replaced as specified. Refer to
USA AND CANADA : Introduction to Periodic Maintenance"
.
FLUID LEAKAGE AND FLUID LEVEL
1. Make sure that fluid is not leaking from the transfer assembly or around it.
2. Check fluid level from the filler plug hole as shown.
CAUTION:
Do not start engine while checking fluid level.
3. Install the filler plug with a new gasket to the transfer. Tighten to
the specified torque. Refer to
CAUTION:
Do not reuse gasket.
TRANSFER FLUID : Replacement
INFOID:0000000006827719
CAUTION:
If using the vehicle for towing, the transfer fluid must be replaced as specified. Refer to
USA AND CANADA : Introduction to Periodic Maintenance"
.
DRAINING
1. Stop engine.
Fluid grade and capacity : Refer to
AND CANADA : Introduction
to Periodic Maintenance"
(United States and Canada)
or
Periodic Maintenance
Schedule"
SDIA3209E
SDIA3287E
2011 Pathfinder
MA-48
< PERIODIC MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
2. Remove the drain plug and gasket and drain the fluid.
3. Install the drain plug with a new gasket to the transfer. Tighten to
the specified torque. Refer to
CAUTION:
Do not reuse gasket.
FILLING
1. Remove the filler plug and gasket.
2. Fill the transfer with new fluid until the fluid level reaches the
specified limit near the filler plug hole.
CAUTION:
Carefully fill fluid. (Fill up for approx. 3 minutes.)
3. Leave the vehicle for 3 minutes, and check fluid level again.
4. Install the filler plug with a new gasket to the transfer. Tighten to
the specified torque. Refer to
CAUTION:
Do not reuse gasket.
PROPELLER SHAFT
PROPELLER SHAFT : Checking Propeller Shaft
INFOID:0000000006243429
Check the front and rear propeller shafts for damage, dents, and cracks. Check the joints for looseness and
any damage. Repair or replace as necessary. Refer to
DLN-205, "NVH Troubleshooting Chart"
.
DIFFERENTIAL GEAR OIL
DIFFERENTIAL GEAR OIL : Front Final Drive R180A
INFOID:0000000006243430
DIFFERENTIAL GEAR OIL : Checking Differential Gear Oil
INFOID:0000000006827720
DIFFERENTIAL GEAR OIL LEAKAGE AND LEVEL
1. Make sure that differential gear oil is not leaking from the front final drive assembly or around it.
2. Check the differential gear oil level from the filler plug hole as
shown.
CAUTION:
Do not start engine while checking differential gear oil level.
3. Install the filler plug with a new gasket on it to the front final drive
assembly. Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
DIFFERENTIAL GEAR OIL : Changing Differential Gear Oil
INFOID:0000000006827721
DRAINING
SDIA3286E
Fluid grade and capacity : Refer to
AND CANADA : Fluids and
Lubricants"
SDIA3287E
LDIA0176E
2011 Pathfinder
CHASSIS AND BODY MAINTENANCE
MA-49
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
1. Stop the engine.
2. Remove the drain plug and gasket from the front final drive
assembly to drain the differential gear oil.
3. Install the drain plug with a new gasket to the front final drive
assembly. Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
FILLING
1. Remove the filler plug and gasket from the front final drive
assembly.
2. Fill the front final drive assembly with new differential gear oil
until the level reaches the specified level near the filler plug hole.
3. Install the filler plug with a new gasket on it to the front final drive assembly. Tighten to the specified
DLN-359, "Disassembly and Assembly"
.
CAUTION:
Do not reuse gasket.
DIFFERENTIAL GEAR OIL : Front Final Drive M205
INFOID:0000000006243433
DIFFERENTIAL GEAR OIL : Checking Differential Gear Oil
INFOID:0000000006827722
DIFFERENTIAL GEAR OIL LEAKAGE AND LEVEL
1. Make sure that differential gear oil is not leaking from the front final drive assembly or around it.
2. Check the differential gear oil level from the filler plug hole as
shown.
CAUTION:
Do not start engine while checking differential gear oil level.
3. Install the filler plug with sealant applied on the threads to the
front final drive assembly. Tighten to the specified torque. Refer
DLN-393, "Disassembly and Assembly"
.
• Use High Performance Thread Sealant or equivalent. Refer to
GI-14, "Recommended Chemical Products and Sealants"
DIFFERENTIAL GEAR OIL : Changing Differential Gear Oil
INFOID:0000000006827723
DRAINING
1. Stop the engine.
2. Remove the drain plug from the front final drive assembly to drain the differential gear oil.
3. Install the drain plug with sealant applied on the threads to the front final drive assembly. Tighten to the
specified torque. Refer to
DLN-393, "Disassembly and Assembly"
.
• Use High Performance Thread Sealant or equivalent. Refer to
GI-14, "Recommended Chemical Prod-
LDIA0175E
Differential gear oil
grade and capacity
: Refer to
AND CANADA : Fluids and
Lubricants"
(United States
"FOR MEXICO : Fluids and
Lubricants"
LDIA0176E
LDIA0176E
2011 Pathfinder
MA-50
< PERIODIC MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
FILLING
1. Remove the filler plug from the front final drive assembly.
2. Fill the front final drive assembly with new differential gear oil
until the level reaches the specified level near the filler plug hole.
3. Install the filler plug with sealant applied on the threads to the
front final drive assembly. Tighten to the specified torque. Refer to
DLN-393, "Disassembly and Assem-
• Use High Performance Thread Sealant or equivalent. Refer to
GI-14, "Recommended Chemical Prod-
DIFFERENTIAL GEAR OIL : Rear Final Drive R200
INFOID:0000000006243436
DIFFERENTIAL GEAR OIL : Checking Differential Gear Oil
INFOID:0000000006827725
OIL LEAKAGE AND OIL LEVEL
1. Make sure that differential gear oil is not leaking from the rear final drive assembly or around it.
2. Check the differential gear oil level from the filler plug hole as
shown.
CAUTION:
Do not start engine while checking differential gear oil level.
3. Install the filler plug with a new gasket on it to the rear final drive
assembly. Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
DIFFERENTIAL GEAR OIL : Changing Differential Gear Oil
INFOID:0000000006827726
DRAINING
1. Stop the engine.
2. Remove the drain plug and gasket from the rear final drive
assembly to drain the differential gear oil.
3. Install the drain plug with a new gasket to the rear final drive
assembly. Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
FILLING
Differential gear oil
grade and capacity
: Refer to
AND CANADA : Fluids and
Lubricants"
(United States
and Canada) or
"FOR MEXICO : Fluids and
Lubricants"
LDIA0176E
LDIA0163E
LDIA0162E
2011 Pathfinder
CHASSIS AND BODY MAINTENANCE
MA-51
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
1. Remove the filler plug and gasket from the rear final drive
assembly.
2. Fill the rear final drive assembly with new differential gear oil
until the level reaches the specified level near the filler plug hole.
3. Install the filler plug with a new gasket on it to the rear final drive assembly. Tighten to the specified torque.
DLN-429, "Disassembly and Assembly"
CAUTION:
Do not reuse gasket.
DIFFERENTIAL GEAR OIL : Rear Final Drive R230
INFOID:0000000006243439
DIFFERENTIAL GEAR OIL : Checking Differential Gear Oil
INFOID:0000000006827727
OIL LEAKAGE AND OIL LEVEL
1. Make sure that differential gear oil is not leaking from the rear final drive assembly or around it.
2. Check the differential gear oil level from the filler plug hole as
shown.
CAUTION:
Do not start engine while checking differential gear oil level.
3. Install the filler plug with a new gasket on it to the rear final drive
assembly. Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
DIFFERENTIAL GEAR OIL : Changing Differential Gear Oil
INFOID:0000000006827728
DRAINING
1. Stop the engine.
2. Remove the drain plug and gasket from the rear final drive
assembly to drain the differential gear oil.
3. Install the drain plug with a new gasket to the rear final drive
assembly. Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
FILLING
Differential gear oil
grade and capacity
: Refer to
AND CANADA : Fluids and
Lubricants"
(United States
MEXICO : Fluids and Lubri-
cants"
(Mexico)
LDIA0163E
LLIA0068E
LLIA0068E
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст