Nissan Xterra. Manual — part 570
AXLE BEARING
RAX-13
< UNIT REMOVAL AND INSTALLATION >
[C200]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
AXLE BEARING
Removal and Installation
INFOID:0000000009484505
The axle bearing must be replaced every time the axle shaft is removed and installed. Refer to
CAUTION:
Do not reuse the axle bearing.
RAX-14
< UNIT REMOVAL AND INSTALLATION >
[C200]
AXLE OIL SEAL
AXLE OIL SEAL
Removal and Installation
INFOID:0000000009484506
The axle oil seal must be replaced every time the axle shaft is removed and installed. Refer to
.
CAUTION:
Do not reuse the axle oil seal.
SERVICE DATA AND SPECIFICATIONS (SDS)
RAX-15
< SERVICE DATA AND SPECIFICATIONS (SDS)
[C200]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Axle Specification
INFOID:0000000009484507
Unit: mm (in)
Shim Washers
INFOID:0000000009484508
Unit: mm (in)
*: Always check with the Parts Department for the latest parts information.
Axial end play
0 - 0.07 (0 - 0.003)
Snap ring to shim washer clearance
0.2 (0.008) or less
Snap ring outer diameter installed
47.5 (1.87) maximum
Total end play
0.02 - 0.15 (0.0008 - 0.0059)
Available shim washers
ID Paint Dot Color
Thickness
Part Number*
Pink
2.5 (0.098)
43086-EB08C
Black
2.4 (0.094)
43086-EB07C
Purple
2.3 (0.091)
43086-EB06C
Yellow
2.2 (0.087)
43086-EB05C
Green
2.1 (0.083)
43086-EB04C
Red
2.0 (0.079)
43086-EB03C
White
1.9 (0.075)
43086-EB02C
Blue
1.8 (0.071)
43086-EB01C
RAX-16
< PRECAUTION >
[M226]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010202791
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution
INFOID:0000000009484510
When installing rubber parts, final tightening must be carried out under unladen condition* with tires
on ground.
* Fuel, radiator coolant and engine oil full. Spare tire, jack, hand tools and mats in designated posi-
tions.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст