Nissan Xterra. Manual — part 699
ASSEMBLY
TM-309
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
24. Install output speed sensor (1) to transmission case and tighten
bolt (
) to specified torque.
CAUTION:
• Do not subject sensor to impact by dropping or hitting it.
• Do not disassemble sensor.
• Do not allow metal filings or any foreign material to get on
the sensor's front edge magnetic area.
• Do not place sensor in an area affected by magnetism.
25. Install new rear oil seal until it is flush into the rear extension
case (2WD models) using Tool or adapter case (4WD models)
using suitable tool.
CAUTION:
• Apply ATF to rear oil seal.
• Do not reuse rear oil seal.
26. Install return spring (1) to parking pawl (2).
27. Install parking pawl (with return spring) and pawl shaft to rear
extension (2WD models) or adapter case (4WD models).
Output speed sensor bolt : 5.8 N·m (0.59 kg-m, 51 in-lb)
JSDIA1321ZZ
Tool number
: ST33400001 (J-26082)
WCIA0475E
SCIA6180J
SCIA3424E
TM-310
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
ASSEMBLY
28. Install parking actuator support to rear extension (2WD models)
or adapter case (4WD models).
29. Install needle bearing (1) to rear extension (2WD models) or
adapter case (4WD models).
CAUTION:
Apply petroleum jelly to needle bearing.
30. Install seal rings to output shaft.
CAUTION:
• Do not reuse seal rings.
• Apply petroleum jelly to seal rings.
31. Install parking gear to output shaft.
32. Install output shaft in transmission case.
CAUTION:
Do not mistake front of shaft for rear because both sides
look similar (thinner end is front side).
SCIA3423E
SCIA6179J
SCIA5209E
SCIA5247E
SCIA5030E
ASSEMBLY
TM-311
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
33. Install bearing race to output shaft.
34. Install rear extension assembly (2WD models) or adapter case assembly (4WD models) according to the
following procedures.
a. 2WD models
i.
Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to
GI-21, "Recommended Chemical Prod-
.) to rear extension assembly as shown.
CAUTION:
Completely remove all moisture, oil, old sealant and any
foreign material from the transmission case and rear exten-
sion assembly mating surfaces.
ii.
Install rear extension assembly to transmission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
iii. Install the rear extension assembly bolts and tighten to the spec-
ified torque.
• Brackets (1)
• Brackets (2)
• Self-sealing bolts (3)
• Bolt (A)
CAUTION:
Do not reuse self-sealing bolt.
SCIA5245E
SCIA5212E
SCIA5029E
Rear extension
assembly bolt
: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt
: 61 N·m (6.2 kg-m, 45 ft-lb)
JSDIA0293ZZ
TM-312
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
ASSEMBLY
b. 4WD models
i.
Install gasket onto transmission case.
CAUTION:
• Completely remove all moisture, oil, old gasket and any
foreign material from the transmission case and adapter
case assembly mating surfaces.
• Do not reuse gasket.
ii.
Install adapter case assembly to transmission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
iii. Tighten adapter case assembly to specified torque.
• 1: Bolts
• 2: Brackets
• 3: Self-sealing bolts
CAUTION:
Do not reuse self-sealing bolt (3).
35. Install direct clutch assembly in reverse brake.
CAUTION:
Make sure that drum support edge surface and direct clutch
inner boss edge surface come to almost same place.
SCIA5231E
SCIA5186E
Adapter case
assembly bolt
: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt : 61 N·m (6.2 kg-m, 45 ft-lb)
SCIA7220E
SCIA5019E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст