Nissan Xterra. Manual — part 489
IP-24
< UNIT DISASSEMBLY AND ASSEMBLY >
CENTER CONSOLE ASSEMBLY
CENTER CONSOLE ASSEMBLY
Exploded View
INFOID:0000000009485686
Disassembly and Assembly
INFOID:0000000009485687
DISASSEMBLY
1. Remove center console. Refer to
IP-21, "Removal and Installation"
2. Remove center console lid.
3. Remove hinge from center console lid.
4. Remove rear finisher assembly.
5. Remove rear cup holder assembly.
6. Remove brackets.
7. Disconnect the harness connectors from center console.
8. Remove cup holder insert and cup holder finisher.
9. Remove center console bin.
10. Remove center console bracket.
11. Remove wire harness bracket.
AWJIA1014ZZ
1.
Shift selector finisher (M/T)
2.
Shift selector finisher (A/T)
3.
Center console front base
4.
Bracket
5.
Center console rear base
6.
Bracket
7.
Wire harness bracket
8.
Rear finisher assembly
9.
Rear cup holder assembly
10. Center console lid hinge
11. Center console lid
12. Center console bin
13. USB connector
14. Power Socket
15. Cup holder insert
16. Cup holder finisher
A.
Bolt
CENTER CONSOLE ASSEMBLY
IP-25
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
ASSEMBLY
Assembly is in the reverse order of disassembly.
LU-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
LU
A
LU
N
O
P
CONTENTS
ENGINE LUBRICATION SYSTEM
VQ40DE
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Liquid Gasket . . . . . . . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
SYSTEM DESCRIPTION . . . . . . . ..
LUBRICATION SYSTEM . . . . . . . . .
Lubrication Circuit . . . . . . . . . . . . .....
System Chart . . . . . . . . . . . . . . ....
PERIODIC MAINTENANCE . . . . . . ..
ENGINE OIL . . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
Changing Engine Oil . . . . . . . . . . . . .
OIL FILTER . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
OIL COOLER . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
OIL PUMP . . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
UNIT DISASSEMBLY AND ASSEMBLY .
OIL PUMP . . . . . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
LU-2
< PRECAUTION >
[VQ40DE]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010203626
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Liquid Gasket
INFOID:0000000010203662
REMOVAL OF LIQUID GASKET
• After removing the bolts and nuts, separate the mating surface and
remove the old liquid gasket using Tool.
CAUTION:
Do not damage the mating surfaces.
• Tap the seal cutter to insert it (1).
• In areas where the Tool is difficult to use, lightly tap to slide it (2).
LIQUID GASKET APPLICATION PROCEDURE
Tool number
: KV10111100 (J-37228)
WBIA0566E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст