Qashqai J11. Door & Lock — part 2
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-33
< SYSTEM DESCRIPTION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SYSTEM (INTELLIGENT KEY SYSTEM)
INTELLIGENT KEY SYSTEM
INTELLIGENT KEY SYSTEM : System Diagram
INFOID:0000000010434547
INTELLIGENT KEY SYSTEM : System Description
INFOID:0000000010434548
• The Intelligent Key system is a system that makes it possible to lock and unlock the door locks (door lock/
unlock function) by carrying the Intelligent Key, which operates based on the results of electronic ID verifica-
tion using two-way communication between the Intelligent Key and the vehicle (BCM).
CAUTION:
The driver should always carry the Intelligent Key
• The settings for each function can be changed with CONSULT.
• If an Intelligent Key is lost, a new Intelligent Key can be registered. A maximum of 4 Intelligent Keys can be
registered.
• It is possible to perform a diagnosis on the system and register an Intelligent Key with CONSULT.
JMKIB3310GB
Function
Description
Refer
Door lock
Lock/unlock can be performed by pressing the request switch
Back door open
The back door can be opened by carrying the Intelligent Key and pressing the
back door opener switch.
Super lock
When all doors are closed super lock system can be set/release by Intelligent
Key or door request switch
DLK-34
< SYSTEM DESCRIPTION >
[TYPE 1]
SYSTEM (INTELLIGENT KEY SYSTEM)
DOOR LOCK FUNCTION
DOOR LOCK FUNCTION : System Diagram
INFOID:0000000010434549
DOOR LOCK FUNCTION : System Description
INFOID:0000000010434550
When pressing the door request switch, it is possible to lock and unlock the door by carrying the Intelligent
Key.
OPERATION DESCRIPTION
• When the BCM detects that each door request switch is pressed, it activates the outside key antenna and
inside key antenna corresponding to the pressed door request switch and transmits the request signal to the
Intelligent Key. And then, check that the Intelligent Key is near the door.
• If the Intelligent Key is within the outside key antenna detection area, it receives the request signal and
transmits the key ID signal to the BCM via remote keyless entry receiver.
• BCM receives the key ID signal and compares it with the registered key ID.
• BCM lock/unlock each door, sets/releases super lock, and blinks hazard warning lamps (lock: 1 time, unlock:
2 times) at the same time as a reminder.
NOTE:
Information of super lock function.
Refer to
DLK-37, "SUPER LOCK FUNCTION : System Description"
OPERATION CONDITION
Remote keyless entry
Lock/unlock can be performed by pressing the remote controller button of the In-
telligent Key
Key reminder
The key reminder buzzer sounds a warning if the door is locked with the key left
inside the vehicle
Warning
If an action that does not meet the operating condition of the Intelligent Key sys-
tem is taken, the buzzer sounds to inform the driver
Engine start
The engine can be turned on while carrying the Intelligent Key
Interior room lamp control
Interior room lamp is controlled according to door lock/unlock state
Function
Description
Refer
JMKIB3311GB
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-35
< SYSTEM DESCRIPTION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
If the following conditions are satisfied, door lock/unlock operation is performed if the door request switch is
operated.
*: Even with a registered Intelligent Key remaining inside the vehicle, door locks can be unlocked from outside of the vehicle with a spare
Intelligent Key as long as key IDs are different.
OUTSIDE KEY ANTENNA DETECTION AREA
The outside key antenna detection area of door lock/unlock function
is in the range of approximately 80 cm (31.50 in) surrounding the
driver, passenger door handles (1) and back door handle (2). How-
ever, this operating range depends on the ambient conditions.
ANTI-HIJACK FUNCTION
Information of super lock system with anti-hijack function.
Refer to
DLK-37, "SUPER LOCK FUNCTION : System Description"
.
HAZARD REMINDER FUNCTION
When doors are locked or unlocked by door request switch, BCM blinks hazard warning lamps as a reminder.
Reminder function does not operate if ignition switch in ON position.
How to Change Reminder Function Operation Mode
With CONSULT
Reminder function operation mode can be changed using CONSULT.
Refer to
DLK-48, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 1)"
AUTO DOOR LOCK FUNCTION
After door is unlocked by door request switch operation and if 30 seconds or more passes without performing
the following operation, all doors are automatically locked. However, operation check function does not acti-
vate.
Auto door lock mode can be changed by the “AUTO LOCK SET” mode in “WORK SUPPORT”. Refer to
48, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 1)"
DOOR LOCK STATUS INDICATOR OPERATION
Each door request switch operation
Operation condition
Lock
• All doors are closed
• Ignition switch is in the OFF position
• P position warning is not activated
• Intelligent Key is outside the vehicle
• Intelligent Key is within outside key antenna detection area
Unlock
• All doors are closed
• Ignition switch is in the OFF position
• Intelligent Key is outside the vehicle
• Intelligent Key is within outside key antenna detection area *
JMKIA4534ZZ
Door lock operation
(With door request switch)
Hazard warning lamp blink
Lock
Once
Unlock (all door unlock)
Twice
Unlock (anti-hijack operation)
Twice (quick)
Operating condition
• Door switch is ON (door is open)
• Door is locked
• Push switch is pressed
DLK-36
< SYSTEM DESCRIPTION >
[TYPE 1]
SYSTEM (INTELLIGENT KEY SYSTEM)
• Door lock status indicator turns indicator lamp ON or OFF and indicates door lock or unlock state.
• For door lock status indicator operation, refer to
.
LIST OF OPERATION RELATED PARTS
Parts marked with
×
are the parts related to operation.
BACK DOOR OPEN FUNCTION
BACK DOOR OPEN FUNCTION : System Diagram
INFOID:0000000010683500
BACK DOOR OPEN FUNCTION : System Description
INFOID:0000000010683393
BACK DOOR OPEN FUNCTION
• When the BCM detects that back door opener switch is pressed, it activates the outside key antenna (rear
bumper) and inside key antenna and transmits the request signal to the Intelligent Key. And then, check that
the Intelligent Key is near the back door.
• If the Intelligent Key is within the outside key antenna detection area, it receives the request signal and
transmits the key ID signal to the BCM via remote keyless entry receiver.
• BCM receives the key ID signal and compares it with the registered key ID.
• If the verification result is OK, BCM opens back door.
OPERATION CONDITION
If the following conditions are satisfied, the back door can be opened.
Door lock function
In
te
lli
ge
nt
Key
Re
mo
te
ke
yl
es
s en
try rec
e
iv
e
r
Door switch
Do
or re
qu
es
t s
w
it
ch
Do
or l
o
c
k
ac
tua
to
r
In
si
d
e
ke
y an
ten
n
a
Out
s
id
e ke
y a
n
ten
n
a
CAN co
mm
un
ic
ati
o
n
sy
s
tem
BC
M
Do
or
lo
c
k
st
atu
s
ind
ic
a
to
r
Hazard w
a
rning
lamp
P
u
s
h
-b
utt
on ig
nit
ion
s
w
itc
h
Co
mb
in
ati
o
n
me
te
r
Door lock/unlock function
×
×
×
×
×
×
×
×
Hazard reminder function
×
×
×
×
Door lock status indicator operation
×
×
Anti-hijack function
×
×
×
×
×
×
Auto door lock function
×
×
×
×
JMKIB3635GB
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-37
< SYSTEM DESCRIPTION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
*
: Even with a registered Intelligent Key remaining inside the vehicle, back door can be opened from outside of
the vehicle with a spare Intelligent Key as long as key IDs are different.
OUTSIDE KEY ANTENNA DETECTION AREA
The outside key antenna detection area of back door open function
is in the range of approximately 80 cm (31.50 in) surrounding back
door opener switch
. However, this operating range depends on
the ambient conditions.
LIST OF OPERATION RELATED PARTS
Parts marked with
×
are the parts related to operation.
SUPER LOCK FUNCTION
SUPER LOCK FUNCTION : System Description
INFOID:0000000010434552
• Super lock provides a higher anti-theft performance than a conventional door lock function.
• BCM controls the super lock function.
• When all doors are closed super lock system can be set/release by Intelligent Key or door request switch.
• When super lock is set, inside handle of doors do not work.
SUPER LOCK SET OPERATION (LOCK OPERATION)
Super Lock Set by Intelligent Key
When Intelligent Key lock button is operated while all doors are in unlock state, super lock of all doors is set,
and simultaneously, all doors are locked.
Super Lock Set by Door Request Switch
When door request switch (driver side, passenger side, or back door) is operated while all doors are in unlock
state, super lock of all doors is set, and simultaneously, all doors are locked.
SUPER LOCK RELEASE OPERATION (UNLOCK OERATION) WITH ANTI-HIJACK MODE
Super Lock Release by Intelligent Key
Back door opener switch operation
Operation condition
Open
• All door: locked and closed
• Ignition switch: OFF
• Intelligent Key is within outside key antenna (rear bumper) detection area
*
JMKIA1955ZZ
Function
Int
e
llig
en
t Ke
y
Re
mo
te ke
yl
es
s e
n
try rec
e
iv
er
Ba
ck d
o
o
r op
en
er ac
tu
a
to
r
Ba
ck d
o
o
r swi
tc
h
In
si
de
k
e
y
an
te
nn
a
Out
s
id
e k
e
y
a
n
tenn
a
(rea
r bu
mp
er)
BCM
Ba
ck d
o
o
r op
en
er swi
tch
Back open function (back door opener switch)
×
×
×
×
×
×
×
×
DLK-38
< SYSTEM DESCRIPTION >
[TYPE 1]
SYSTEM (INTELLIGENT KEY SYSTEM)
When Intelligent Key unlock button is operated while super lock of all doors is set, super lock of all doors is
released, and simultaneously, driver door are unlocked. When Intelligent Key unlock button is operated again
within 5 seconds of the 1st unlock button operation, all doors are unlocked.
Super Lock Release by Door Request Switch (Driver Side)
When driver side door request switch is operated while super lock of all doors is set, super lock of all doors is
released, and simultaneously, driver door are unlocked. When driver side door request switch is operated
again within 5 seconds of the 1st driver side door request switch operation, all doors are unlocked.
Super Lock Release by Door Request Switch (Passenger Side)
When passenger side door request switch is operated while super lock of all doors is set, super lock of all
doors is released, and simultaneously, all doors are unlocked.
Super Lock Release by Door Request Switch (Back Door)
When back door request switch is operated while super lock of all doors is set, super lock of all doors is
released, and simultaneously, back door are unlocked. When back door request switch is operated again
within 5 seconds of the 1st back door request switch operation, all doors are unlocked.
SUPER LOCK RELEASE OPERATION (UNLOCK OERATION) WITHOUT ANTI-HIJACK MODE
Super Lock Release by Intelligent Key
When Intelligent Key unlock button is operated while super lock of all doors is set, super lock of all doors is
released, and simultaneously, all doors are unlocked.
Super Lock Release by Door Request Switch
When door request switch (driver side, passenger side or back door) is operated while super lock of all doors
is set, super lock of all doors is released, and simultaneously, all doors are unlocked.
ANTI-HIJACK FUNCTION SETTING
With CONSULT
Anti-hijack function can be set to ON/OFF using CONSULT.
Refer to
DLK-47, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK) (Type 1)"
.
Without CONSULT
Anti-hijack function can be set to ON/OFF by user with a registered Intelligent Keyfob.
• ON/OFF can be switched when Intelligent Key lock button and unlock button are pressed simultaneously for
5 seconds or more while steering lock is locked.
• When mode is switched, hazard warning lamp blinks.
REMOTE KEYLESS ENTRY FUNCTION
REMOTE KEYLESS ENTRY FUNCTION : System Diagram
INFOID:0000000010434553
OFF
→
ON
: 1 blink
ON
→
OFF
: 3 blinks
JMKIB3313GB
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-39
< SYSTEM DESCRIPTION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY FUNCTION : System Description
INFOID:0000000010434554
The Intelligent Key has the same functions as the remote control entry system. Therefore, it can be used in the
same manner as the remote controller by operating the door lock/unlock button.
OPERATION
Remote keyless entry system controls operation of the following items.
• Door lock/unlock
• Super lock set/release
• Anti-hijack function
• Hazard reminder function
• Auto door lock
• Door lock status indicator operation
OPERATION AREA
To check that the Intelligent Key works normally, use within 1 m (3 ft) range of each doors, however the opera-
ble range may differ according to surroundings.
DOOR LOCK/UNLOCK FUNCTION
• When door lock/unlock button of the Intelligent Key is pressed, lock signal or unlock signal transmitted from
Intelligent Key to BCM via remote keyless entry receiver.
• BCM receives the signal and compares it with the registered key ID to the vehicle.
• BCM transmits door lock/unlock signal to each door lock actuator, super lock actuator and operates each
door lock actuator, when key ID matches. At the same time, BCM blinks hazard warning lamps (lock: 1 time,
unlock: 2 times).
OPERATION CONDITION
If the following condition are satisfied, remote keyless entry operation is performed when the Intelligent Key is
operated.
ANTI-HIJACK FUNCTION
Information of super lock system with anti-hijack function.
Refer to
DLK-48, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 1)"
AUTO DOOR LOCK FUNCTION
After door is unlocked by Intelligent Key button operation and if 30 seconds or more passes without performing
the following operation, all doors are locked. However, operation check function does not activate.
Auto door lock mode can be changed by the “AUTO LOCK SET” mode in “WORK SUPPORT”. Refer to
48, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 1)"
DOOR LOCK STATUS INDICATOR OPERATION
• Door lock status indicator turns indicator lamp ON or OFF and indicates door lock or unlock state.
• For door lock status indicator operation, refer to
.
HAZARD REMINDER FUNCTION
Operation Description
When doors are locked or unlocked by Intelligent Key button operation, BCM blinks hazard warning lamps as
a reminder.
Remote controller operation
Operation condition
Lock/set
• All doors closed
• Ignition switch in the OFF position
• P position warning is not activated
Unlock/release
• Ignition switch is in the OFF position
• Intelligent Key is outside the vehicle
• P position warning is not activated
Operating condition
• Door switch is ON (door is open)
• Door is locked
• Push switch is pressed
DLK-40
< SYSTEM DESCRIPTION >
[TYPE 1]
SYSTEM (INTELLIGENT KEY SYSTEM)
How to Change Reminder Function Operation Mode
With CONSULT
Reminder function operation mode can be changed using CONSULT.
Refer to
DLK-48, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 1)"
LIST OF OPERATION RELATED PARTS
Parts marked with
×
are the parts related to operation.
KEY REMINDER FUNCTION
KEY REMINDER FUNCTION : System Diagram
INFOID:0000000010434555
KEY REMINDER FUNCTION : System Description
INFOID:0000000010434556
Key reminder is the function that prevents the key from being left in the vehicle.
Key reminder has the following 3 functions.
Door lock operation
(With Intelligent Key button)
Hazard warning lamp blink
Lock
Once
Unlock (all door unlock)
Twice
Unlock (anti-hijack operation)
Twice (quick)
Remote keyless entry functions
In
te
lli
ge
nt Key
Doo
r swi
tch
Do
or l
o
c
k
ac
tua
to
r
Pu
sh
-bu
tto
n ign
iti
on
swi
tch
CAN c
o
mm
un
ic
ati
o
n
sy
s
tem
BCM
Co
mb
in
ati
o
n
me
te
r
Hazard warning lamp
Doo
r lo
ck
s
tat
us
in
di
ca
to
r
Door lock/unlock function by remote control button
×
×
×
×
×
Hazard reminder function
×
×
×
×
×
×
Anti-hijack function
×
×
×
×
×
×
Auto door lock function
×
×
×
Door lock status indicator operation
×
×
JMKIB3314GB
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-41
< SYSTEM DESCRIPTION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
*:If the door closing impact shocks the door lock knob, or contacts against baggage with the door lock knob might activate the door locks
accidentally but unlock operation is perform in these cases.
CAUTION:
• The above function operates when the Intelligent Key is inside the vehicle. However, there may be
times when the Intelligent Key cannot be detected, and this function does not operate when the Intel-
ligent Key is on the instrument panel, rear parcel shelf, or in the glove box. Also, this system some-
times does not operate if the Intelligent Key is in the door pocket for the open door.
WARNING FUNCTION
WARNING FUNCTION : System Description
INFOID:0000000010434557
OPERATION DESCRIPTION
The warning function are as per the following items and are given to the user as warning information and
warnings using combinations of Intelligent Key warning buzzer, combination meter buzzer and information dis-
play in combination meter.
• Intelligent Key system malfunction
• OFF position warning
• P position warning
• Take away warning
• Door lock operation warning
• Engine start information
• Intelligent Key low battery warning
• Key ID verification information
• Steering lock information
• Key ID warning
OPERATION CONDITION
Operation condition of warning and information is as per the following table.
Key remainder func-
tion
Operation condition
Operation
Driver side door
opened
Right after door is locked by door lock/unlock switch or driver door lock
knob operation under the following conditions
• Ignition switch is in the OFF position
• Intelligent Key is inside the vehicle
• Driver side door is opened
All doors unlock
Driver side door
closed*
Right after driver side door is closed under the following conditions
• Intelligent Key is inside the vehicle
• Driver side door is opened
• Driver side door is in unlock state
All doors unlock
Door is open or closed
Right after all doors are closed under the following conditions
• Intelligent Key is inside the vehicle
• Any door is opened
• All doors are locked.
• All doors unlock
• Honk Intelligent Key warn-
ing buzzer
Warning/Information functions
Operation procedure
Intelligent Key system malfunction
A malfunction is detected on BCM and key warning lamp turns ON
OFF position warning
When condition A or B is satisfied
• Condition A
- Turn ignition switch from ON to OFF while door is open
• Condition B
- Intelligent Key backside is contacted to push-button ignition switch while
brake pedal is depressed and ignition switch is LOCK or OFF (When the In-
telligent Key battery is discharged)
- Door switch (driver side): ON (Door is open)
P position warning*
For internal
• Shift position: Except P position
• Engine is running to stopped (Ignition switch is ON to OFF)
For external
• P position warning (For internal) operates
• Door switch: ON to OFF (Door is open to close)
• Intelligent Key cannot be detected inside the vehicle
DLK-42
< SYSTEM DESCRIPTION >
[TYPE 1]
SYSTEM (INTELLIGENT KEY SYSTEM)
*: M/T models do not apply.
WARNING METHOD
The following table shows the alarm or warning methods with chime.
Take away warning
Door status changes
from open to close
• Ignition switch: Except LOCK or OFF position
• Door switch: ON to OFF (Door is open to close)
• Registered Intelligent Key is not detected inside the vehicle
Door status is open
• Ignition switch: Except OFF position
• Door switch: ON (Door is open)
• Registered Intelligent Key is not detected inside the vehicle during Key ID ver-
ification for 5 seconds
Push button-ignition
switch operation
• Ignition switch: OFF position
• Press push-button ignition switch
• Registered Intelligent Key is not detected inside the vehicle
Door lock operation warning
When door lock operation is requested while door lock operating condition of
door request switch not satisfied
Engine start information
Ignition switch is ON po-
sition
• Ignition switch: ON position
• Shift position: P position*
• Engine is stopped
Ignition switch is except
ON position
• Ignition switch: Except ON position
• Shift position: P position*
• Intelligent Key can be detected inside the vehicle
Ignition switch is ON po-
sition to OFF position
• Ignition switch: ON position to OFF position
• Shift position: P position
NOTE:
Engine start information turns ON for several seconds and then turns OFF, when
ignition switch is turned to the ON position from the OFF position. Engine start
information does not turn ON until opening and closing of driver door is detected
again.
Intelligent Key low battery warning
BCM detects that Intelligent Key is low battery, after ignition switch is turned ON
Key ID verification information
• Ignition switch: LOCK position
• Push-button ignition switch: Pressed
• Registered Intelligent Key is not detected inside the vehicle
Steering lock information
When the steering lock can not be unlocked
Key ID warning
• Push-button ignition switch is pressed
• Registered Intelligent Key is not detected inside the vehicle
Warning/Information functions
Operation procedure
Warning/Information functions
Information display
(Symbol)
Information display
(Message)
Warning chime
Combina-
tion meter
buzzer
Intelligent
Key warn-
ing buzzer
Intelligent Key system malfunction
Key System Error
See Owner
′
s Manu-
al
—
—
OFF position warning
—
—
Activate
—
JMKIB1526ZZ
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-43
< SYSTEM DESCRIPTION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
P position warn-
ing
For internal
Shift to Park
Activate
—
For external
—
—
—
Active
Take away
warning
Door is open to
close
No Key Detected
Activate
Activate
Door is open
—
—
Push-ignition
switch operation
Activate
—
Door lock operation warning
—
—
—
Activate
Engine start information (A/T mod-
els)
—
—
—
Engine start information (M/T mod-
els)
—
—
—
Intelligent Key low battery warning
Key Battery Low
—
—
Key ID verification information
—
—
—
Warning/Information functions
Information display
(Symbol)
Information display
(Message)
Warning chime
Combina-
tion meter
buzzer
Intelligent
Key warn-
ing buzzer
JMKIB1527ZZ
JMKIB1526ZZ
JMKIB1396ZZ
JMKIB3307ZZ
JMKIB1529ZZ
JMKIB1399ZZ
DLK-44
< SYSTEM DESCRIPTION >
[TYPE 1]
SYSTEM (INTELLIGENT KEY SYSTEM)
LIST OF OPERATION RELATED PARTS
Parts marked with
×
are the parts related to operation.
Steering lock information
—
—
—
Key ID warning
Key ID Incorrect
—
—
Warning/Information functions
Information display
(Symbol)
Information display
(Message)
Warning chime
Combina-
tion meter
buzzer
Intelligent
Key warn-
ing buzzer
JMKIB1401ZZ
JMKIB1526ZZ
Function
In
te
lli
ge
nt K
e
y
Pu
sh
-bu
tto
n i
g
n
iti
on
swi
tch
Do
or swi
tch
Doo
r re
qu
es
t s
w
itc
h
In
si
de
key an
ten
n
a
O
u
tsi
d
e
ke
y
an
ten
n
a
S
tee
ring
l
o
c
k
u
n
it
In
te
lli
ge
nt K
e
y
warn
in
g b
u
z
z
e
r
Co
mbi
n
at
io
n
m
e
te
r (wa
rni
n
g
bu
zz
er)
Com
b
ina
tio
n me
ter (inf
orm
a
ti
on
di
sp
la
y)
CAN c
o
m
m
uni
ca
tio
n
sy
st
em
BCM
Intelligent Key system malfunction
×
×
×
OFF position warning
×
×
×
×
P position warning
×
×
×
×
×
Take away warning
Door is open or close
×
×
×
×
×
×
×
×
Door is open
×
×
×
×
×
×
Push-button ignition switch
operation
×
×
×
×
×
×
×
Door lock operation warning
×
×
×
×
×
×
×
Engine start information
×
×
×
×
×
×
Intelligent Key low battery warning
×
×
×
×
×
Key ID verification information
×
×
×
×
×
×
Steering lock information
×
×
×
×
Key ID warning
×
×
×
×
×
SYSTEM (BACK DOOR OPENER SYSTEM)
DLK-45
< SYSTEM DESCRIPTION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SYSTEM (BACK DOOR OPENER SYSTEM)
System Description
INFOID:0000000010479484
SYSTEM DIAGRAM
BACK DOOR OPENER OPERATION
When back door opener switch is pressed, BCM operates back door opener actuator.
NOTE:
Back door opener actuator is not for locking the back door. The function is only to open the back door.
OPERATION CONDITION
If the following conditions are satisfied, back door opener operation is performed.
NOTE:
• When battery terminal is disconnected and reconnected during all doors unlock state, back door may not
open.
• Regardless of door lock actuator state, BCM resets recognition of all doors unlock state approximately 30
seconds after battery terminal is disconnected and BCM recognizes that all doors are in lock state.
• When battery terminal is reconnected and back door does not open, have BCM recognize that all doors are
in unlock state.
JMKIA6011GB
Back door opener switch operation
Operation condition
Back door open
• All doors are unlocked.
• Vehicle speed is less than 5 km/h (3 MPH)
DLK-46
< SYSTEM DESCRIPTION >
[TYPE 1]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010471212
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Exterior lamp
HEAD LAMP
×
×
×
Interior room lamp control
INT LAMP
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
PTC heater control
AIR CONDITONER
×
Intelligent Key system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
Interior room lamp battery saver
BATTERY SAVER
×
Back door open
TRUNK
×
Vehicle security
THEFT ALM
×
×
RAP
RETAINED PWR
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
Signal buffer system
SIGNAL BUFFER
×
×
DIAGNOSIS SYSTEM (BCM)
DLK-47
< SYSTEM DESCRIPTION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR LOCK
DOOR LOCK : CONSULT Function (BCM - DOOR LOCK) (Type 1)
INFOID:0000000010434559
BCM CONSULT FUNCTION
CONSULT performs the following functions via CAN communication with BCM.
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
CONSULT screen item
Indication/Unit
Description
BATTERY VOLTAGE
V
Battery voltage of the moment a particular DTC is detected.
VEHICLE SPEED
km/h
Vehicle speed of the moment a particular DTC is detected.
EXTERNAL TEMP
°
C
External temperature of the moment a particular DTC is detected
VEHICLE COND
—
NOTE:
This item is displayed, but cannot be use this item.
DOOR LOCK STATUS
—
NOTE:
This item is displayed, but cannot be use this item.
POWER SUPPLY
COUNTER
min
Displays the cumulative time from the time that the battery terminal is connected.
Monitor item
Description
DOOR LOCK-UNLOCK SET
Anti-hijack function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
SIGNATURE LIGHT SETTING
Signature light function can be changed to operation with this mode
• On: Operate
• Off: Non-operation
Monitor Item
Contents
REQ SW-DR
Indicated [On/Off] condition of door request switch (driver side)
REQ SW-AS
Indicated [On/Off] condition of door request switch (passenger side)
REQ SW-BD/TR
Indicated [On/Off] condition of back door request switch
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicated [On/Off] condition of rear door switch LH
DOOR SW-BK
Indicated [On/Off] condition of back door switch
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock unlock switch
KEY CYL LK-SW
NOTE:
This item is displayed, but cannot be monitored
KEY CYL UN-SW
NOTE:
This item is displayed, but cannot be monitored
DLK-48
< SYSTEM DESCRIPTION >
[TYPE 1]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 1)
INFOID:0000000010434560
WORK SUPPORT
SHOCK SENSOR
Indicates [NOMAL/On/Off] condition of circuit between BCM and air bag diagnosis sensor unit
• NORMAL: Ignition switch ON. (BCM is receiving normal condition signal from air bag diagnosis sensor
unit.)
• ON: During the receiving of air bag signal from air bag diagnosis sensor unit
• OFF: After the receiving of air bag signal from air bag diagnosis sensor unit
KEY SW
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Contents
Test item
Description
DOOR LOCK
This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LOCK” on CONSULT screen is touched
• The all door lock actuators are unlocked when “ALL UNLOCK” on CONSULT screen is touched
SUPER LOCK
This test is able to check super lock actuator operation
• The all door lock actuators are set when “LOCK” on CONSULT screen is touched
• The all door lock actuators are released when “UNLOCK” on CONSULT screen is touched
DOOR LOCK IND
This test is able to check door lock status indicator operation
• On: Operate
• Off: Non-operation
Monitor item
Description
INSIDE ANT DIAGNOSIS
This function allows inside key antenna self-diagnosis
LOCK/UNLOCK BY I-KEY
Door lock/unlock function by door request switch mode can be changed to operation in this
mode
• On: Operate
• Off: Non-operation
ENGINE START BY I-KEY
Engine start function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
TRUNK/GLASS HATCH OPEN
NOTE:
This item is displayed, but cannot be monitored
AUTO LOCK SET
Auto door lock operation time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes
SHORT CRANKING OUTPUT
NOTE:
This item is displayed, but cannot be monitored
IGN/ACC BATTERY SAVER
Ignition battery saver system mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
ANSWER BACK
NOTE:
This item is displayed, but cannot be used
ANSWER BACK I-KEY LOCK UN-
LOCK
Reminder function (door request switch) mode can be selected from the following with this
mode
• On: hazard warning lamp operate
• Off: hazard warning lamp operate
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст