Qashqai J11. Door & Lock — part 3
DIAGNOSIS SYSTEM (BCM)
DLK-49
< SYSTEM DESCRIPTION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SELF-DIAG RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ANSWER BACK KEYLESS LOCK
UNLOCK
Reminder function (Intelligent Key) mode can be selected from the following with this mode
• On: hazard warning lamp operate
• Off: hazard warning lamp operate
WELCOME LIGHT OP SET
NOTE:
This item is indicated, but not used
Monitor item
Description
Monitor Item
Condition
REQ SW -DR
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
Indicates [On/Off] condition of door request switch (passenger side)
REQ SW -BD/TR
Indicates [On/Off] condition of back door request switch
PUSH SW
Indicates [On/Off] condition of push-button ignition switch
CLUTCH SW*
1
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
DETE/CANCL SW
Indicates [On/Off] condition of P position
START CLUTCH SW
Indicates [On/Off] condition of clutch pedal position switch
PUSH SW -IPDM
Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B
Indicates [On/Off] condition of ignition relay 1
NEUTRAL SW - IPDM
Indicates [On/Off] condition of park/neutral position switch
SFT PN -IPDM
Indicates [On/Off] condition of P or N position
STARTER RELAY - IPDM
Indicates [On/Off] condition of starter relay
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
ST/INHIRELAY-IPDM
Display the starter relay/starter control relay status signal from IPDM E/R via CAN communica-
tion
REVERSE SIGNAL - IPDM
Indicates [On/Off] condition of R position
CRANKING PERMIT - ECM
Display the engine cranking permit signal from ECM via CAN communication
IS STATUS - ECM
Indicates [On/Off] condition of stop/start system
STARTER CUT RELAY - ECM
Indicates [On/Off] condition of starter control relay signal from ECM via CAN communication
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]
IGN REQ - IPDM
Display the ignition request signal from IPDM E/R via CAN communication
STARTER REQ - IPDM
Display the starter request signal from IPDM E/R via CAN communication
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
ID OK FLAG
Indicates [Set/Reset] condition of Intelligent Key ID
PRMT ENG STRT
Indicates [Set/Reset] condition of engine start possible
DLK-50
< SYSTEM DESCRIPTION >
[TYPE 1]
DIAGNOSIS SYSTEM (BCM)
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored
I-KEY OK FLAG
Indicates [KEY On/NOT On] condition of Intelligent Key ID and Intelligent Key is detected inside
vehicle
PRBT ENG STRT
Indicates whether or not the engine is in start prohibited status
ID AUTHENT CANCEL TIMER
Indicates whether or not it is in engine start possible status when Intelligent Key verification is
unnecessary
ACC BATTERY SAVER
Indicates [On/Off] whether or not ignition battery saver is in operation
CRNK PRBT TMR
Indicates [On/Off] whether or not in cranking prohibited status due to starter motor protection
function operation
AUT CRANK TMR
Indicates [On/Off] whether or not in AUTO CRANKING MODE status
CRNK PRBT TME
Indicates the time for changing from cranking prohibited status to cranking possible status
AUT CRANK TMR
Indicates the time that AUTO CRANKING MODE operates
CRANKING TME
Indicates the cranking operation time
SHORT CRANK
NOTE:
This item is displayed, but not used
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored
S/L IGN OFF POSITION
Indicates [On/Off] condition of Ignition OFF signal
S/L SENSOR CIRCUIT 1
Indicates [Gnd/Off] condition of steering lock unit sensor circuit
S/L SENSOR CIRCUIT 2
Indicates [On/Off] condition of steering lock unit sensor circuit
S/L POWER OUTPUT
Indicates [On/Off] condition of steering lock unit power supply
S/L POWER CHECK
Indicates [On/Off] condition of steering lock unit power supply
ANTICIPATED POWER
Indicates [On/Off] condition of anticipated power supply
S/L LOCK REQ
Indicates [On/Off] condition of steering lock unit lock request signal
S/L - BCM (CAN)
Indicates [On/Off] condition of CAN communication
S/L POWER ERROR
Indicates [On/Off] condition of steering lock unit power supply error
VEH SPEED ERROR (S/L)
Indicates [On/Off] condition of vehicle speed signal
VEH SPEED NORMAL (S/L)
Indicates [On/Off] condition of vehicle speed signal
ENGINE RUNNING (S/L)
Indicates [On/Off] condition of engine running
S/L ID DISCORD
Indicates [Correct/Incorrect] condition of ID verification
S/L ANTI-SCAN MODE
Indicates [On/Off] condition of antiscan mode
S/L LOCK NOT PERMIT
Indicates [Inhibition/No inhbt] condition of inhibit steering lock
S/L UNLOCK (CAN)
Indicates [Finished/Unfinished] condition of steering lock unit unlock
S/L ID STATUS (CAN)
Indicates [Coded/Blank] condition of registration ID
S/L RESET STATUS (CAN)
Indicates [Exit/No exit] condition of steering lock unit reset signal
S/L LO-LEVEL MALFUNC (CAN)
Indicates [Malf/No malf] condition of lo-level malfunction
S/L LOCK POSITION (CAN)
Indicates [Armed/Malf/Unlocked/Undefined] condition of lock/unlock position signal
S/L ACT MALFUNCTION (CAN)
Indicates [Malf/No malf] condition of steering lock unit malfunction
S/L HI-LEVEL MALFUNC (CAN)
Indicates [Malf/No malf] condition of hi-level malfunction
S/L OPERATION PRHBT (SPD)
Indicates [On/Off] condition of vehicle speed signal
S/L OPERATION PRHBT (PWR)
Indicates [Allowed/Forbid] condition of safety line inhibition
S/L SENSOR POWER (CAN)
Indicates [On/Off] condition of sensor test power supply
S/L SEN TEST PERMIT (CAN)
Indicates [Forbid/Authorize] condition of sensor test
S/L STAT NOT DETECT (CAN)
Indicates [Ok/Undefind] condition of steering lock undefined position signal
Monitor Item
Condition
DIAGNOSIS SYSTEM (BCM)
DLK-51
< SYSTEM DESCRIPTION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
S/L LOCKING FINISHED (CAN)
Indicates [Unfinshd/Finished] condition of steering lock unit lock status signal
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE PBD
NOTE:
This item is displayed, but cannot be monitored
KEY SW
NOTE:
This item is displayed, but cannot be monitored
IGN SW
NOTE:
This item is displayed, but cannot be monitored
START SW
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
Test item
Description
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Buzzer 1: Combination meter buzzer sounds (pipipi...) when CONSULT screen is touched
• Buzzer 2: Combination meter buzzer sounds (pipi-pipi-...) when CONSULT screen is
touched
• Buzzer 3: Combination meter buzzer sounds (pipipipi-pipipipi-...) when CONSULT screen is
touched
• Off: Non-operation
INDICATOR
This test is able to check warning lamp operation
• KEY ON:[ Intelligent key system malfunction] displays when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation
FLASHER
This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched
HORN
NOTE:
This item is displayed, but cannot be used
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
MIRROR +5
NOTE:
This item is displayed, but cannot be used
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched
PUSH SWITCH INDICATOR
This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT screen is touched
DLK-52
< SYSTEM DESCRIPTION >
[TYPE 1]
DIAGNOSIS SYSTEM (BCM)
TRUNK
TRUNK : CONSULT Function (BCM - TRUNK) (Type 1)
INFOID:0000000010434561
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ENGINE START REQUEST
This test is able to check BCM sends starter request signal to IPDM E/R via CAN communi-
cation
• MODE 1: IGN ON, START request OFF
• MODE 2: IGN OFF, START request ON
• MODE 3: IGN ON, START request ON
• Off: Non-operation
IGNITION RELAY
NOTE:
This item is displayed, but cannot be used
STARTER CUT RELAY
This test is able to operate the starter control relay
• On: Operates
• Off: Non-operation
ENGINE START
NOTE:
This item is displayed, but cannot be used
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is displayed, but cannot be used
REVERSE LAMP TEST
NOTE:
This item is displayed, but cannot be used
KEYFOB P/W TEST
NOTE:
This item is displayed, but cannot be used
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTOMATIC BACK DOOR
NOTE:
This item is displayed, but cannot be used
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk room lamp operation
• On: Operates
• Off: Non-operation
Test item
Description
Monitor Item
Contents
PUSH SW
Indicates [On/Off] condition of push switch
STARTER CUT RELAY
Indicates [On/Off] condition of starter control relay
DETECTION SENSOR (BK)
NOTE:
This item is displayed, but cannot be monitored
VEH SPEED 1
Indicates [Km/h] condition of vehicle speed signal from combination meter
KEY CYL SW-TR
NOTE:
This item is displayed, but cannot be monitored
TR CANCEL SW
NOTE:
This item is displayed, but cannot be monitored
TRUNK LID OPENER SW
NOTE:
This item is displayed, but cannot be monitored
DIAGNOSIS SYSTEM (BCM)
DLK-53
< SYSTEM DESCRIPTION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR OEPENR SW
Indicates [On/Off] condition of back door opener switch
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Contents
DLK-54
< ECU DIAGNOSIS INFORMATION >
[TYPE 1]
BCM
ECU DIAGNOSIS INFORMATION
BCM
List of ECU Reference
INFOID:0000000010434562
ECU
Reference
BCM
DOOR & LOCK SYSTEM
DLK-55
< WIRING DIAGRAM >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
WIRING DIAGRAM
DOOR & LOCK SYSTEM
Wiring Diagram
INFOID:0000000010434563
JRKWD0753GB
DLK-56
< WIRING DIAGRAM >
[TYPE 1]
DOOR & LOCK SYSTEM
JRKWE3972GB
DOOR & LOCK SYSTEM
DLK-57
< WIRING DIAGRAM >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
JRKWE3973GB
DLK-58
< WIRING DIAGRAM >
[TYPE 1]
DOOR & LOCK SYSTEM
JRKWE3974GB
DOOR & LOCK SYSTEM
DLK-59
< WIRING DIAGRAM >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
JRKWE3975GB
DLK-60
< WIRING DIAGRAM >
[TYPE 1]
DOOR & LOCK SYSTEM
JRKWE3976GB
DOOR & LOCK SYSTEM
DLK-61
< WIRING DIAGRAM >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
JRKWE3977GB
DLK-62
< WIRING DIAGRAM >
[TYPE 1]
DOOR & LOCK SYSTEM
JRKWE3978GB
DOOR & LOCK SYSTEM
DLK-63
< WIRING DIAGRAM >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
JRKWE3979GB
DLK-64
< WIRING DIAGRAM >
[TYPE 1]
DOOR & LOCK SYSTEM
JRKWE3980GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст