Qashqai J11. Door & Lock — part 52
INTELLIGENT KEY BATTERY
DLK-833
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTELLIGENT KEY BATTERY
Removal and Installation
INFOID:0000000010672474
1.
Release the lock knob at the back of the Intelligent Key and remove the mechanical key.
2.
Insert a flat-blade screwdriver (A) wrapped with a cloth into the
slit of the corner and twist it to separate the upper part from the
lower part.
CAUTION:
• Do not touch the circuit board or battery terminal.
• The key fob is water-resistant. However, if it does get wet,
immediately wipe it dry.
3.
Replace the battery with new one.
4.
Align the tips of the upper and lower parts, and then push them
together until it is securely closed.
CAUTION:
• When replacing battery, keep dirt, grease, and other for-
eign materials off the electrode contact area.
• After replacing the battery, check that all Intelligent Key
functions work normally.
PIIB6221E
Battery replacement
:Coin-type lithium battery
(CR2032)
PIIB6222E
DLK-834
< HOW TO USE THIS MANUAL >
[TYPE 6]
APPLICATION NOTICE
HOW TO USE THIS MANUAL
APPLICATION NOTICE
Information
INFOID:0000000010674130
Check the vehicle type to use the service information in this section.
Service information
Destination
Type 1
For Europe
With Intelligent Key and super lock
Type 2
• For Europe
• For South Africa
• For Russia, Ukraine and Kazakhstan
With Intelligent Key, without super lock
Type 3
For Europe
Without Intelligent Key, with super lock
Type 4
• For Europe
• For South Africa
• For Russia, Ukraine and Kazakhstan
Without Intelligent Key and super lock
Type 5
• For Australia
• For General export
With Intelligent Key, without super lock
Type 6
• For Australia
• For General export
Without Intelligent Key and super lock
PRECAUTIONS
DLK-835
< PRECAUTION >
[TYPE 6]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011772973
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000011772974
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Precautions for Removing Battery Terminal
INFOID:0000000011772975
• With the adoption of Auto ACC function, ACC power is automatically supplied by operating the intelligent key
or remote keyless entry or by opening/closing the driver side door. In addition, ACC power is supplied even
after the ignition switch is turned to the OFF position, i.e. ACC power is supplied for a certain fixed time.
PIIB3706J
DLK-836
< PRECAUTION >
[TYPE 6]
PRECAUTIONS
• When disconnecting the 12V battery terminal, turn off the ACC
power before disconnecting the 12V battery terminal, observing
“How to disconnect 12V battery terminal” described below.
NOTE:
Some ECUs operate for a certain fixed time even after ignition
switch is turned OFF and ignition power supply is stopped. If the
battery terminal is disconnected before ECU stops, accidental DTC
detection or ECU data damage may occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
HOW TO DISCONNECT 12V BATTERY TERMINAL
Disconnect 12V battery terminal according to instruction described below.
1.
Open the hood.
2.
Turn ignition switch to the ON position.
3.
Turn ignition switch to the OFF position with the driver side door opened.
4.
Get out of the vehicle and close the driver side door.
5.
Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse
of the specified time.
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
6.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
Work
INFOID:0000000011772976
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operational.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
SEF289H
D4D engine
: 20 minutes
HRA2DDT
: 12 minutes
K9K engine
: 4 minutes
M9R engine
: 4 minutes
R9M engine
: 4 minutes
V9X engine
: 4 minutes
PREPARATION
DLK-837
< PREPARATION >
[TYPE 6]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000010672481
Tool name
Description
Engine ear
Locating the noise
Remover tool
Remove the clips, pawls, and metal clips
Power tool
SIIA0995E
PIIB7923J
PIIB1407E
DLK-838
< SYSTEM DESCRIPTION >
[TYPE 6]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000010672482
Component Description
INFOID:0000000010672483
1.
Power window main switch
(door lock/unlock switch)
2.
BCM
Refer to
SYSTEM : Component Parts Loca-
tion"
3.
Combination meter
4.
Front power window switch (passen-
ger side) (door lock and unlock
switch)
5.
Door lock assembly
6.
Door switch
7.
Back door lock assembly
8.
Back door opener switch
JMKIB3273ZZ
Item
Function
Back door lock assembly
Opens the back door with the back door open signal from BCM.
BCM
BCM detects the vehicle status according to signals from each door switch and
each outside/inside key antenna. BCM transmits drive signal to door lock actuator
when BCM receives operation signal from remote keyless entry receiver and each
switch.
Refer to
BCS-6, "BODY CONTROL SYSTEM : Component Parts Location"
for de-
tailed installation location.
Combination meter
• Performs operation method guide and warning with buzzer.
• Transmits vehicle seep signal to CAN communication line.
Door lock actuator
• Inputs locks/unlocks signal from BCM and locks/unlocks each door.
• Integrated in each door lock assembly.
Door lock and unlock switch
Transmits door lock/unlock operation to BCM.
Door switch
Detects door open/close condition.
Keyfob
Transmits button operation to remote keyless entry receiver.
Key switch
Key switch detects that ignition key is inserted into the ignition key cylinder, and
then transmits the signal to BCM.
POWER DOOR LOCK SYSTEM
DLK-839
< SYSTEM DESCRIPTION >
[TYPE 6]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
POWER DOOR LOCK SYSTEM
System Diagram
INFOID:0000000010672484
System Description
INFOID:0000000010672485
DOOR LOCK FUNCTION
Door Lock and Unlock Switch
• The door lock and unlock switch (driver side) is built into power window main switch.
• The door lock and unlock switch (passenger side) is built into front power window switch (passenger side).
• Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all doors are
locked.
• Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors actu-
ator are unlocked.
INTERIOR ROOM LAMP CONTROL FUNCTION
Interior room lamp is controlled according to door lock /unlock state, refer to
CONTROL SYSTEM : System Description"
AIR BAG INTERLOCK UNLOCK FUNCTION
When ignition switch is ON and BCM receives shock status signal, it operates automatically to unlock all
doors. Air bag diagnosis sensor unit sends the shock status signal to BCM via CAN communication.
KEY REMINDER FUNCTION
• While ignition key is inserted in ignition key cylinder and driver door is open, door is not locked when door
lock and unlock switch is pressed in the lock direction. This prevents keyfob from being left in the vehicle.
• While door lock and unlock switch is pressed in the lock direction, combination meter buzzer sounds and
warns.
DOOR LOCK STATUS INDICATOR OPERATION
The door lock status indicator indicates door lock status under the following condition.
JMKIB2483GB
Indicator operation
Ignition position
Door status
Lock operation
ON (30 minutes timer)
OFF
All doors are closed and door
is locked
Door lock and unlock switch
ON
ON
All doors are closed and door
is locked
Door lock and unlock switch
ON (1 minute timer)
OFF
All doors are closed and door
is locked
Keyfob or auto door lock func-
tion
ON
ON
All doors are closed and door
is locked
Keyfob or auto door lock func-
tion
DLK-840
< SYSTEM DESCRIPTION >
[TYPE 6]
POWER DOOR LOCK SYSTEM
ON
→
OFF
–
(All doors are closed
→
any
door is open) or (All doors are
locked
→
any door is un-
locked)
–
ON (timer is running)
→
ON
(timer is stop)
OFF
→
ON
–
–
ON
→
ON (30 minutes timer)
ON
→
OFF
–
Door lock and unlock switch
ON
→
ON (1 minute timer)
ON
→
OFF
–
Keyfob or auto door lock func-
tion
Indicator operation
Ignition position
Door status
Lock operation
REMOTE KEYLESS ENTRY SYSTEM
DLK-841
< SYSTEM DESCRIPTION >
[TYPE 6]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY SYSTEM
System Diagram
INFOID:0000000010672486
System Description
INFOID:0000000010672487
DOOR LOCK AND UNLOCK OPERATION
• When door lock and unlock button of keyfob is pressed, door lock and unlock signal transmits from keyfob to
BCM via remote keyless entry receiver.
• When BCM receives the door lock and unlock signal, it operates door lock actuator, blinks the hazard lamp
at the same time as a reminder.
OPERATION CONDITION
If the following conditions are satisfied, door lock/unlock operation is performed if the keyfob is operated.
OPERATION AREA
To ensure that the keyfob works effectively, use within 100 cm (3 ft) range of each door, however the operable
range may differ according to surroundings.
SELECTIVE UNLOCK FUNCTION
• When LOCK signal is transmitted from keyfob, all doors are locked.
• When UNLOCK signal is transmitted from keyfob once, driver side door is unlocked.
• Then, if UNLOCK signal is transmitted from keyfob again, all other doors are unlocked.
How to change anti-hijack mode.
With CONSULT
Selective unlock mode can be set to ON or OFF using CONSULT.
Refer to
DLK-845, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK) (Type 6)"
PANIC ALARM FUNCTION
When keyfob panic alarm button is pressed while ignition switch is OFF, BCM transmits theft warning horn
request signal to IPDM E/R. Then, IPDM E/R turns on and off horn intermittently.
The horn sounds intermittently.
The alarm automatically turns off.
• After 25 seconds
• When BCM receives any signal from keyfob
REMINDER FUNCTION
When doors are locked or unlocked by keyfob, BCM blinks hazard warning lamps as a reminder and transmits
horn chirp signal to IPDM E/R. IPDM E/R sounds horn as a reminder.
JMKIB3618GB
Remote controller operation
Operation condition
Lock
• Key switch is off
• All doors are closed
Unlock
Key switch is off
DLK-842
< SYSTEM DESCRIPTION >
[TYPE 6]
REMOTE KEYLESS ENTRY SYSTEM
The hazard and horn reminder has a horn chirp mode (C mode) and a non-horn chirp mode (S mode).
Operating Function of Hazard and Horn Reminder
Hazard and horn reminder does not operate if ignition switch ON position.
How to change hazard and horn reminder mode
With CONSULT
DLK-846, "MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT) (Type 6)"
Without CONSULT
When LOCK and UNLOCK signals are sent from the Intelligent Key for more than 2 seconds at the same time,
the hazard and horn reminder mode is changed and hazard warning lamp blinks and horn sounds as per the
following items:
AUTO DOOR LOCK FUNCTION
After door is unlocked by keyfob button operation and if 60 seconds or more passes without performing the fol-
lowing operation, all doors are automatically locked. However, operation check function does not activate.
Auto door lock mode can be changed by the “AUTO LOCK SET” mode in “WORK SUPPORT”. Refer to
846, "MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT) (Type 6)"
INTERIOR ROOM LAMP CONTROL FUNCTION
Interior room lamp is controlled according to door lock/unlock state, refer to
CONTROL SYSTEM : System Description"
C mode
S mode
Keyfob operation
Lock
Unlock
Back door
open
Lock
Unlock
Back door
open
Hazard warning lamp blinks
Twice
Once
—
Twice
—
—
Horn sound
Once
—
—
—
—
—
JMKIB1365GB
Operating condition
• Door switch is ON (door is open)
• Door is locked
• Key switch is ON
BACK DOOR OPENER SYSTEM
DLK-843
< SYSTEM DESCRIPTION >
[TYPE 6]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR OPENER SYSTEM
System Description
INFOID:0000000010672488
SYSTEM DIAGRAM
BACK DOOR OPENER OPERATION
When back door opener switch is pressed, BCM operates back door opener actuator.
NOTE:
Back door opener actuator is not for locking the back door. The function is only to open the back door.
OPERATION CONDITION
If the following conditions are satisfied, back door opener operation is performed.
NOTE:
• When battery terminal is disconnected and reconnected during all doors unlock state, back door may not
open.
• Regardless of door lock actuator state, BCM resets recognition of all doors unlock state approximately 30
seconds after battery terminal is disconnected and BCM recognizes that all doors are in lock state.
• When battery terminal is reconnected and back door does not open, have BCM recognize that all doors are
in unlock state.
JMKIA6011GB
Back door opener switch operation
Operation condition
Back door open
• All doors are unlocked.
• Vehicle speed is less than 5 km/h (3 MPH)
DLK-844
< SYSTEM DESCRIPTION >
[TYPE 6]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010674528
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Exterior lamp
HEAD LAMP
×
×
×
Interior room lamp control
INT LAMP
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
PTC heater control
AIR CONDITONER
×
Intelligent Key system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
Interior room lamp battery saver
BATTERY SAVER
×
Back door open
TRUNK
×
Vehicle security
THEFT ALM
×
×
RAP
RETAINED PWR
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
Signal buffer system
SIGNAL BUFFER
×
×
DIAGNOSIS SYSTEM (BCM)
DLK-845
< SYSTEM DESCRIPTION >
[TYPE 6]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR LOCK
DOOR LOCK : CONSULT Function (BCM - DOOR LOCK) (Type 6)
INFOID:0000000010672490
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
CONSULT screen item
Indication/Unit
Description
BATTERY VOLTAGE
V
Battery voltage of the moment a particular DTC is detected.
VEHICLE SPEED
km/h
Vehicle speed of the moment a particular DTC is detected.
EXTERNAL TEMP
°
C
External temperature of the moment a particular DTC is detected
VEHICLE COND
—
NOTE:
This item is displayed, but cannot be use this item.
DOOR LOCK STATUS
—
NOTE:
This item is displayed, but cannot be use this item.
POWER SUPPLY
COUNTER
min
Displays the cumulative time from the time that the battery terminal is connected.
Monitor item
Description
DOOR LOCK-UNLOCK SET
Anti-hijack function can be changed to operate with this mode
• On: Operate
• Off: Non-operation
Monitor Item
Contents
IGN ON SW
Indicated [On/Off] condition of ignition switch in ON position
KEY ON SW
Indicated [On/Off] condition of key switch
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock unlock switch
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicated [On/Off] condition of rear door switch LH
BACK DOOR SW
Indicated [On/Off] condition of back door switch
LOCK STATUS
Indicated [On/Off] condition of front door driver side
ACC ON SW
Indicated [On/Off] condition of ignition switch in ACC position
KEYLESS LOCK
Indicated [On/Off] condition of lock signal from key fob
KEYLESS UNLOCK
Indicated [On/Off] condition of unlock signal from key fob
SHOCK SENSOR
Indicates [NOMAL/On/Off] condition of circuit between BCM and air bag diag-
nosis sensor unit
• NORMAL: Ignition switch ON. (BCM is receiving normal condition signal
from air bag diagnosis sensor unit.)
• ON: During the receiving of air bag signal from air bag diagnosis sensor unit
• OFF: After the receiving of air bag signal from air bag diagnosis sensor unit
KEY CYL LK-SW
NOTE:
This item is displayed, but cannot be monitored
KEY CYL UN-SW
NOTE:
This item is displayed, but cannot be monitored
VEHICLE SPEED
Display the vehicle speed signal received from combination meter by numer-
ical value [Km/h]
DLK-846
< SYSTEM DESCRIPTION >
[TYPE 6]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
MULTI REMOTE ENT
MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT) (Type 6)
INFOID:0000000010738355
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Test item
Description
DOOR LOCK
This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LCK” on CONSULT screen is touched
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT screen is touched
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT screen is
touched
• “BD ULK” is displayed, but cannot be used
• “OTR ULK” is displayed, but cannot be used
DOOR LOCK IND
This test is able to check door lock status indicator operation
• On: Operate
• Off: Non-operation
Test item
Description
AUTO LOCK SET
Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec.
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute
ANSWER BACK
Reminder function (keyfob) mode can be selected from the following with this mode
• On: S mode (horn non-operation)
• Off: C mode (horn operate)
ANSWER BACK KEYLESS
LOCK UNLOCK
Reminder function (keyfob) mode can be selected from the following with this mode
• On: Horn and hazard warning lamp operate
• Off: Only hazard warning lamp operate
WELCOME LIGHT OP SET
NOTE:
This item is displayed, but cannot be used
Monitor Item
Condition
CONFRM ID ALL
Indicates [Yet] at all time.Switches to [Done] when a registered key is inserted into ignition key
cylinder.
CONFRM ID4
CONFRM ID3
CONFRM ID2
CONFRM ID1
NOT REGISTERED
Indicates [ID OK] when key ID that is registered is received or is not yet received. Indicates [ID
NG] when key ID that is not registered is received.
TP 4
Indicates the number of IDs that are registered.
TP 3
TP 2
TP 1
CLUTCH SW*
Indicates [On/Off] condition of clutch interlock switch
DIAGNOSIS SYSTEM (BCM)
DLK-847
< SYSTEM DESCRIPTION >
[TYPE 6]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
TRUNK
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
START CLUTCH SW
Indicates [On/Off] condition of clutch pedal position switch
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from keyfob
KEY SW
Indicates [On/Off] condition of key switch
IGN SW
Indicates [On/Off] condition of ignition switch in ON position
START SW
Indicates [On/Off] condition of ignition switch in START position
Monitor Item
Condition
Test item
Description
FLASHER
This test is able to check flasher operation [LH/RH/Off]
HORN
This test is able to check horn operation
• On: Operates
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
MIRROR+5
NOTE:
This item is indicated, but not monitored
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is indicated, but not monitored
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk/luggage room lamp operation
• On: Operates
• Off: Non-operation
DLK-848
< SYSTEM DESCRIPTION >
[TYPE 6]
DIAGNOSIS SYSTEM (BCM)
TRUNK : CONSULT Function (BCM - TRUNK) (Type 6)
INFOID:0000000010672492
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor Item
Contents
STARTER CUT RELAY
Indicates [On/Off] condition of starter control relay
KEY CYL SW-TR
NOTE:
This item is displayed, but cannot be monitored
TR CANCEL SW
NOTE:
This item is displayed, but cannot be monitored
TRUNK LID OPENER SW
NOTE:
This item is displayed, but cannot be monitored
BACK DOOR OEPENR SW
Indicates [On/Off] condition of back door opener switch
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст