Qashqai J11. Door & Lock — part 51
FRONT DOOR LOCK
DLK-817
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
12. Slide outside handle bracket toward rear of vehicle to remove.
13. Disconnect outside handle cable (1) from outside handle bracket
(2) according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
CAUTION:
Never bend the outside handle cable end.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When installing key rod, rotate key rod holder until a click is felt.
• Check that door lock cables are normally engaged with inside handle and outside handle.
• After installation, check door open/close, and lock/unlock operation.
: Vehicle front
JMKIA5890ZZ
JMKIA5891ZZ
DLK-818
< REMOVAL AND INSTALLATION >
[TYPE 5]
REAR DOOR LOCK
REAR DOOR LOCK
Exploded View
INFOID:0000000010678827
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000010678828
REMOVAL
1.
Remove inside handle. Refer to
DLK-819, "INSIDE HANDLE : Removal and Installation"
.
2.
Remove outside handle bracket. Refer to
DLK-819, "OUTSIDE HANDLE : Removal and Installation"
1.
Outside handle escutcheon
2.
Rear gasket
3.
Outside handle bracket
4.
TORX bolt
5.
Door lock assembly
6.
Inside handle
7.
Cable clip
8.
Front gasket
9.
Outside handle grip
: Pawl
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
JMKIB3255GB
REAR DOOR LOCK
DLK-819
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Remove rear door lower sash mounting bolt, and then remove rear door lower sash.
4.
Disconnect door lock assembly harness connector.
5.
Remove door lock assembly screws, and then remove door lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse door lock assembly screw. Always replace it with a new one when it is removed.
• Check door lock cable is properly engaged with outside handle bracket.
• Check door lock assembly for poor lubrication. Refer to
DLK-819, "DOOR LOCK : Inspection"
• Check door open/close, lock/unlock operation after installation.
DOOR LOCK : Inspection
INFOID:0000000010678829
Check door lock assembly for poor lubrication. Apply body grease if
necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000010678830
REMOVAL
1.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Removal and Installation"
2.
Remove inside handle mounting bolt.
3.
Disengage inside handle from door panel while sliding inside handle toward vehicle rear, and then sepa-
rate inside handle.
4.
Disconnect inside handle cable, and then remove inside handle.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000010678831
REMOVAL
1.
Fully close the rear door glass.
2.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Removal and Installation"
3.
Remove sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
: Body grease
JMKIA8534ZZ
DLK-820
< REMOVAL AND INSTALLATION >
[TYPE 5]
REAR DOOR LOCK
4.
Remove grommet (1) of door side. Loosen, through grommet hole, TORX bolt (2) that fixes outside handle
escutcheon.
5.
While pulling outside handle (1) according to the numerical order
1
→
2 indicated by arrows as shown in the figure, remove outside
handle escutcheon (2).
6.
While pulling outside handle (1) according to the numerical order
1
→
2 indicated by arrows as shown in the figure, slide toward
rear of vehicle to remove outside handle.
7.
Remove front gasket (1) and rear gasket (2).
JMKIB2478ZZ
JMKIB2479ZZ
JMKIA0524ZZ
: Pawl
: Vehicle front
JMKIB1627ZZ
REAR DOOR LOCK
DLK-821
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
8.
Slide outside handle bracket toward rear of vehicle to remove.
9.
Disconnect outside handle cable (1) from outside handle bracket
(2) according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
CAUTION:
Never bend the outside handle cable end.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check that door lock cables are normally engaged with inside handle and outside handle.
• After installation, check door open/close, and lock/unlock operation.
: Vehicle front
JMKIA5890ZZ
JMKIA5891ZZ
DLK-822
< REMOVAL AND INSTALLATION >
[TYPE 5]
BACK DOOR LOCK
BACK DOOR LOCK
Exploded View
INFOID:0000000010678832
Removal and Installation
INFOID:0000000010678833
REMOVAL
1.
Remove back door trim finisher lower. Refer to
INT-31, "Removal and Installation"
2.
Disconnect back door lock harness connector.
3.
Remove back door assembly mounting bolts, and then remove back door lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• After installation, check back door open/close, and lock/unlock operation.
• Check door lock assembly for poor lubrication. Refer to
1.
Back door panel
2.
Back door lock assembly
: N·m (kg-m, ft-lb)
: Body grease
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB3271GB
BACK DOOR LOCK
DLK-823
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Inspection
INFOID:0000000010678834
Check door lock assembly for poor lubrication. Apply body grease if
necessary.
: Body grease
JMKIB0629ZZ
DLK-824
< REMOVAL AND INSTALLATION >
[TYPE 5]
FUEL FILLER LID OPENER
FUEL FILLER LID OPENER
Exploded View
INFOID:0000000010678835
LHD models
JMKIB3264ZZ
1.
Fuel opener cable
2.
Cable protector
3.
Fuel filler lid lock assembly
4.
Bumper rubber
5.
Fuel filler lid assembly
6.
Fuel filler spring
: Clip
: Pawl
: Always replace after every disassembly.
FUEL FILLER LID OPENER
DLK-825
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
RHD models
FUEL FILLER LID
FUEL FILLER LID : Removal and Installation
INFOID:0000000010678836
REMOVAL
1.
Fully open fuel filler lid assembly.
JMKIB3263ZZ
1.
Fuel opener cable
2.
Cable protector
3.
Fuel filler lid lock assembly
4.
Bumper rubber
5.
Fuel filler lid assembly
6.
Fuel filler spring
: Clip
: Pawl
: Always replace after every disassembly.
DLK-826
< REMOVAL AND INSTALLATION >
[TYPE 5]
FUEL FILLER LID OPENER
2.
Remove fuel mounting pin (1).
3.
Remove fixing screws, and then remove fuel filler lid assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• After installation, check fuel filler lid assembly open/close, lock/unlock operation.
• After installation, apply the touch-up paint (the body color) onto the head of the fixing screws.
• Apply anti-corrosion wax to mounting surface of fixing screw and fuel filler lid to prevent rust.
NOTE:
The following table shows the specified values for checking normal installation status.
Unit: mm [in]
FUEL FILLER LID LOCK
FUEL FILLER LID LOCK : Removal and Installation
INFOID:0000000010678837
REMOVAL
1.
Fully open fuel filler lid.
2.
Remove luggage lower finisher RH. Refer to
.
3.
In the order of 1
→
2 as shown in the figure, rotate and disengage
fuel filler lid lock assembly, and then remove fuel filler lid lock
assembly.
NOTE:
Operation is performed easily when rotating fuel filler lid lock
from passenger room side.
4.
In the order of 1
→
4 as shown in the figure. Disengage fuel filler
lid opener cable (1). Remove fuel filler lid opener cable while
pressing stopper pin (2).
JMKIB3183ZZ
Clearance
Evenness
Fuel filler lid – Body side outer
3.7 – 5.3
(0.146 – 0.209)
(-1.0) – (+1.0)
[(-0.039) – (+0.039)]
: Pawl
: Vehicle front
JMKIB1094ZZ
JMKIA5719ZZ
FUEL FILLER LID OPENER
DLK-827
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
FUEL FILLER OPENER CABLE
FUEL FILLER OPENER CABLE : Removal and Installation
INFOID:0000000010678838
REMOVAL
LHD models
1.
Remove hood lock control handle mounting bolts, and then remove hood lock control handle.
2.
Disconnect fuel opener cable (2) from fuel filler lid opener lever
(1) according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
3.
Remove front kicking plate inner LH and rear kicking plate inner LH. Refer to
.
4.
Remove dash side finisher LH. Refer to
INT-18, "Removal and Installation"
.
5.
Remove center pillar lower garnish LH. Refer to
INT-18, "Removal and Installation"
6.
Remove luggage side lower finisher RH. Refer to
.
7.
Disconnect fuel opener cable from fuel filler lid lock assembly. Refer to
LOCK : Removal and Installation"
.
8.
Remove fuel opener cable from each harness protector.
9.
Remove cable protector.
10. Remove fuel opener cable fixing clips, and then remove fuel opener cable.
RHD models
1.
Remove hood lock control handle mounting bolts, and then remove hood lock control handle.
2.
Disconnect fuel opener cable (2) from fuel filler lid opener lever
(1) according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
3.
Remove front kicking plate inner RH and rear kicking plate inner RH. Refer to
.
4.
Remove dash side finisher RH. Refer to
INT-18, "Removal and Installation"
5.
Remove center pillar lower garnish RH. Refer to
INT-18, "Removal and Installation"
.
6.
Remove luggage side lower finisher RH. Refer to
.
7.
Disconnect fuel opener cable from fuel filler lid lock assembly. Refer to
LOCK : Removal and Installation"
.
JMKIA5901ZZ
JMKIA5672ZZ
DLK-828
< REMOVAL AND INSTALLATION >
[TYPE 5]
FUEL FILLER LID OPENER
8.
Remove fuel opener cable from each harness protector.
9.
Remove cable protector.
10. Remove fuel opener cable fixing clips, and then remove fuel opener cable.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse cable protector. Always replace it with a new one when it is removed.
• After installation, check fuel filler lid assembly open/close, lock/unlock operation.
• Never bend cable too much, keeping the radius 100 mm (3.937 in) or more.
DOOR SWITCH
DLK-829
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR SWITCH
Removal and Installation
INFOID:0000000010672468
REMOVAL
Remove the TORX bolt (A), and then remove door switch (1).
INSTALLATION
Install in the reverse order of removal.
JMKIA2173ZZ
DLK-830
< REMOVAL AND INSTALLATION >
[TYPE 5]
INSIDE KEY ANTENNA
INSIDE KEY ANTENNA
CONSOLE
CONSOLE : Removal and Installation
INFOID:0000000010672469
REMOVAL
1.
Remove the console rear finisher. Refer to
IP-19, "Removal and Installation"
2.
Remove the inside key antenna (console) mounting screw
,
and then remove inside key antenna (console)
.
INSTALLATION
Install in the reverse order of removal.
LUGGAGE ROOM
LUGGAGE ROOM : Removal and Installation
INFOID:0000000010672470
REMOVAL
Remove the mounting clip
, and then remove inside key antenna
(luggage room)
.
INSTALLATION
Install in the reverse order of removal.
JMKIB3257ZZ
JMKIB3258ZZ
OUTSIDE KEY ANTENNA
DLK-831
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
OUTSIDE KEY ANTENNA
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000010672471
REMOVAL
Remove the outside handle grip. Refer to
DLK-183, "OUTSIDE HANDLE : Removal and Installation"
INSTALLATION
Install in the reverse order of removal.
REAR BUMPER
REAR BUMPER : Removal and Installation
INFOID:0000000010672472
REMOVAL
1.
Remove the rear bumper fascia assembly. Refer to
EXT-24, "Removal and Installation"
.
2.
Disconnect outside key antenna (rear bumper) connector, and
then remove outside key antenna (rear bumper)
.
INSTALLATION
Install in the reverse order of removal.
JMKIB3259ZZ
DLK-832
< REMOVAL AND INSTALLATION >
[TYPE 5]
INTELLIGENT KEY WARNING BUZZER
INTELLIGENT KEY WARNING BUZZER
Removal and Installation
INFOID:0000000010672473
REMOVAL
1.
Remove the front bumper fascia assembly. Refer to
EXT-20, "Removal and Installation"
2.
Disconnect Intelligent Key warning buzzer connector.
3.
Remove the Intelligent Key warning buzzer mounting bolt
, and
then remove the Intelligent Key warning buzzer
.
INSTALLATION
Install in the reverse order of removal.
JMKIB2758ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст