Qashqai J11. Door & Lock — part 21
RADIATOR CORE SUPPORT
DLK-337
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
10. Remove A/C pipe bracket mounting bolt (1).
11. Remove radiator core support upper mounting bolts, and then remove radiator core support upper.
INSTALLATION
Install in the reverse order of removal.
MR20DD
MR20DD : Exploded View
INFOID:0000000010678770
T/M models
E1BIA1725ZZ
JMKIB3632GB
1.
Radiator core support upper
2.
Air guide RH
3.
Air lower guide
4.
Air guide LH
5.
Air guide plate
:N·m (kg-m, ft-lb)
DLK-338
< REMOVAL AND INSTALLATION >
[TYPE 2]
RADIATOR CORE SUPPORT
CVT models
MR20DD : Removal and Installation
INFOID:0000000010678771
REMOVAL
1.
Remove front grille. Refer to
EXT-26, "Removal and Installation"
2.
Remove air duct (inlet). Refer to
EM-24, "Removal and Installation"
3.
Remove hood switch.
a.
Disconnect hood switch harness connector.
b.
Remove hood switch mounting bolt, and then remove hood switch.
4.
Remove hood lock assembly. Refer to
DLK-361, "HOOD LOCK : Removal and Installation"
.
5.
Remove hood lock control cable fixing clips from radiator core support upper. Refer to
6.
Remove engine room harness fixing clips from radiator core support upper.
7.
Remove crash zone sensor. Refer to
SR-24, "Removal and Installation"
.
8.
Remove horn. Refer to
HRN-7, "Removal and Installation"
9.
Remove radiator mounting bracket. Refer to
10. Remove A/C pipe bracket mounting bolt. Refer to
.
11. Remove radiator core support upper mounting bolts, and then remove radiator core support upper.
INSTALLATION
Install in the reverse order of removal.
K9K
JMKIB3633GB
1.
Radiator core support upper
2.
Air guide RH
3.
Air lower guide
4.
Air guide LH
5.
Air guide plate
:N·m (kg-m, ft-lb)
RADIATOR CORE SUPPORT
DLK-339
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
K9K : Exploded View
INFOID:0000000011734387
K9K : Removal and Installation
INFOID:0000000010478239
REMOVAL
1.
Remove front grille. Refer to
EXT-26, "Removal and Installation"
2.
Remove air duct (inlet). Refer to
EM-426, "Removal and Installation"
.
3.
Remove hood switch.
a.
Disconnect hood switch harness connector.
b.
Remove hood switch mounting bolt, and then remove hood switch.
4.
Remove hood lock assembly. Refer to
DLK-361, "HOOD LOCK : Removal and Installation"
.
5.
Remove hood lock control cable fixing clips from radiator core support upper. Refer to
6.
Remove engine room harness fixing clips from radiator core support upper.
7.
Remove crash zone sensor. Refer to
SR-24, "Removal and Installation"
.
8.
Remove horn. Refer to
HRN-7, "Removal and Installation"
9.
Remove radiator mounting bracket. Refer to
.
10. Remove A/C pipe bracket mounting bolt.
• For Europe: Refer to Refer to
.
• Except for Europe: Refer to Refer to
.
11. Remove radiator core support upper mounting bolts, and then remove radiator core support upper.
INSTALLATION
Install in the reverse order of removal.
R9M
1.
Radiator core support upper
2.
Air guide RH
3.
Air lower guide
4.
Air guide LH
:N·m (kg-m, ft-lb)
JMKIB3298GB
DLK-340
< REMOVAL AND INSTALLATION >
[TYPE 2]
RADIATOR CORE SUPPORT
R9M : Exploded View
INFOID:0000000011734388
T/M models
CVT models
JMKIB3299GB
1.
Radiator core support upper
2.
Air guide RH
3.
Air lower guide
4.
Air guide LH
:N·m (kg-m, ft-lb)
JMKIB3300GB
RADIATOR CORE SUPPORT
DLK-341
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
R9M : Removal and Installation
INFOID:0000000010478241
REMOVAL
1.
Remove front grille. Refer to
EXT-26, "Removal and Installation"
2.
Remove air duct (inlet). Refer to
EM-528, "Removal and Installation"
.
3.
Remove hood switch.
a.
Disconnect hood switch harness connector.
b.
Remove hood switch mounting bolt, and then remove hood switch.
4.
Remove hood lock assembly. Refer to
DLK-361, "HOOD LOCK : Removal and Installation"
.
5.
Remove hood lock control cable fixing clips from radiator core support upper. Refer to
6.
Remove engine room harness fixing clips from radiator core support upper.
7.
Remove crash zone sensor. Refer to
SR-24, "Removal and Installation"
.
8.
Remove horn. Refer to
HRN-7, "Removal and Installation"
9.
Remove radiator mounting bracket. Refer to
.
10. Remove A/C pipe bracket mounting bolt.
• For Europe: Refer to Refer to
.
• Except for Europe: Refer to Refer to
.
11. Remove radiator core support upper mounting bolts, and then remove radiator core support upper.
INSTALLATION
Install in the reverse order of removal.
1.
Radiator core support upper
2.
Air guide RH
3.
Air lower guide
4.
Air guide LH
:N·m (kg-m, ft-lb)
DLK-342
< REMOVAL AND INSTALLATION >
[TYPE 2]
FRONT FENDER
FRONT FENDER
Exploded View
INFOID:0000000010478242
Removal and Installation
INFOID:0000000010478243
CAUTION:
Use protective tape or shop cloth to protect from damage during removal and installation.
REMOVAL
1.
Remove fillet molding. Refer to
EXT-38, "Removal and Installation"
2.
Remove fender protector. Refer to
EXT-33, "Removal and Installation"
3.
Remove front bumper fascia assembly and bumper side bracket. Refer to
EXT-20, "Removal and Installa-
4.
Remove front combination lamp. Refer to
EXL-319, "Removal and Installation"
(HALOGEN HEADLAMP)
EXL-162, "Removal and Installation"
(LED HEADLAMP).
5.
Remove front fender seal.
6.
Remove front fender assembly mounting bolts.
1.
Front fender seal
2.
Front fender assembly
3.
Hoodledge cover
: Pawl
: N·m (kg-m, in-lb)
JMKIB3315GB
FRONT FENDER
DLK-343
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
7.
Remove front fender stiffener (2) from the vehicle body while
carefully pulling upper portion of front fender (1) toward vehicle
outside.
8.
Remove front fender assembly.
CAUTION:
An viscous urethane foam is installed on the back surface of front fender. When removing the
front fender, be careful to not deform the front fender while performing the procedure and remov-
ing the viscous urethane foam a little at a time.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• After installation, apply the touch-up paint (the body color) onto the head of front fender mounting
bolts.
• After installation, adjust the following part.
- Hood assembly: Refer to
DLK-331, "HOOD ASSEMBLY : Adjustment"
.
- Front door: Refer to
DLK-345, "DOOR ASSEMBLY : Adjustment"
.
: Vehicle front
JMKIA5633ZZ
DLK-344
< REMOVAL AND INSTALLATION >
[TYPE 2]
FRONT DOOR
FRONT DOOR
Exploded View
INFOID:0000000010478244
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000010478245
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove front door harness grommet from vehicle body side, and then pull out front door harness.
2.
Disconnect front door harness connector.
3.
Remove mounting bolt of door check link on the vehicle body.
4.
Remove door hinge mounting nuts of door side, and then remove door assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
1.
Front door panel
2.
Grommet
3.
TORX bolt
4.
Door striker
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Body grease
JMKIB3248GB
FRONT DOOR
DLK-345
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Apply anticorrosive agent onto the mounting surface.
• After installation, perform the fitting adjustment. Refer to
DLK-345, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• Check door hinge and door check link rotating part for poor lubrication.
- Door hinge: Refer to
DLK-347, "DOOR HINGE : Inspection"
.
- Door check link: Refer to
DLK-347, "DOOR CHECK LINK : Removal and Installation"
.
DOOR ASSEMBLY : Adjustment
INFOID:0000000010478246
FITTING ADJUSTMENT
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
TORX bolt
7.
Front door hinge
8.
Rear door hinge (upper)
9.
Rear door hinge (lower)
: Always replace after every disassembly.
JMKIB3256GB
DLK-346
< REMOVAL AND INSTALLATION >
[TYPE 2]
FRONT DOOR
Fitting Adjustment Standard
Check the clearance and surface height between front door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm [in]
Fitting Adjustment Procedure
1.
Remove front fender. Refer to
DLK-342, "Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
3.
Adjust the surface height of front door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting bolts on vehicle body side.
6.
Raise front door at rear end to adjust clearance of the front door according to the fitting standard dimen-
sion.
7.
After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• After installation, apply touch-up paint (the body color) onto the head of hinge mounting bolts
and nuts.
• Check door hinge rotating part for poor lubrication. Apply body grease if necessary. Refer to
DLK-347, "DOOR HINGE : Inspection"
8.
Install front fender. Refer to refer to
DLK-342, "Removal and Installation"
.
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000010478247
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse mounting TORX bolt. Always replace it with a new one when it is removed.
• Check front door open/close, lock/unlock operation after installation.
• After installation, perform the fitting adjustment. Refer to
DLK-345, "DOOR ASSEMBLY : Adjust-
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000010478248
REMOVAL
: N·m (kg-m, ft-lb)
: Body grease
Portion
Standard
Front fender – Front door
A – A
H
Clearance
3.3 – 5.3
[0.130 – 0.209]
I
Surface
height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
Front door – Rear door
B – B
J
Clearance
3.3 – 5.3
[0.130 – 0.209]
K
Surface
height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
FRONT DOOR
DLK-347
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
1.
Remove front fender. Refer to
DLK-342, "Removal and Installation"
2.
Remove front door assembly. Refer to
DLK-344, "DOOR ASSEMBLY : Removal and Installation"
.
3.
Remove front door hinge mounting bolts (body side), and then remove front door hinge.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check front door open/close, lock/unlock operation after installation.
• After installation, perform the fitting adjustment. Refer to
DLK-345, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• After installation, check door hinge rotating part for poor lubrication. Refer to
DOOR HINGE : Inspection
INFOID:0000000010478249
Check door hinge rotating part for poor lubrication. Apply body
grease if necessary.
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000010478250
REMOVAL
1.
Fully close the front door glass.
2.
Remove front door finisher. Refer to
INT-12, "FRONT DOOR FINISHER : Removal and Installation"
.
3.
Remove front door speaker.
a.
Disconnect front door speaker harness connector.
b.
Remove front door speaker mounting bolts, and then remove front door speaker.
4.
Remove check link mounting bolts of vehicle body side.
5.
Remove check link mounting bolts of door side.
6.
Take door check link out from the hole of door panel.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check front door open/close operation after installation.
• After installation, check door check link rotating part for poor lubrication. Refer to
: Body grease
JMKIB0321ZZ
DLK-348
< REMOVAL AND INSTALLATION >
[TYPE 2]
FRONT DOOR
DOOR CHECK LINK : Inspection
INFOID:0000000010478251
Check door hinge rotating part for poor lubrication. Apply body
grease if necessary.
: Body grease
JMKIB0322ZZ
REAR DOOR
DLK-349
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR
Exploded View
INFOID:0000000010478252
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000010478253
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing rear door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove rear door harness grommet from vehicle body side, and then pull out rear door harness.
2.
Disconnect rear door harness connector.
3.
Remove mounting bolt of door check link on the vehicle.
4.
Remove door hinge mounting nuts of door side, and then remove rear door assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
1.
Rear door panel
2.
Grommet
3.
TORX bolt
4.
Door striker
5.
Door check link
6.
Door hinge (lower)
7.
Door hinge (upper)
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Body grease
JMKIB3250GB
DLK-350
< REMOVAL AND INSTALLATION >
[TYPE 2]
REAR DOOR
• Apply anticorrosive agent onto the mounting surface.
• After installation, perform the fitting adjustment. Refer to
DLK-350, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• Check door hinge and door check link rotating part for poor lubrication.
- Door hinge: Refer to
DLK-352, "DOOR HINGE : Inspection"
.
- Door check link: Refer to
DLK-353, "DOOR CHECK LINK : Inspection"
.
DOOR ASSEMBLY : Adjustment
INFOID:0000000010478254
FITTING ADJUSTMENT
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
TORX bolt
7.
Front door hinge
8.
Rear door hinge (upper)
9.
Rear door hinge (lower)
: Always replace after every disassembly.
JMKIB3256GB
REAR DOOR
DLK-351
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Fitting Adjustment Standard
Check the clearance and surface height between rear door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm [in]
Fitting Adjustment Procedure
1.
Remove center pillar lower garnish. Refer to
INT-18, "Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
3.
Adjust the surface height of rear door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting nuts and bolts on body side.
6.
Raise rear door at rear end to adjust clearance of rear door according to the fitting standard dimension.
7.
After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• After installation, apply touch-up paint (the body color) onto the head of hinge mounting bolts
and nuts.
• Check door hinge rotating part for poor lubrication. Refer to
DLK-347, "DOOR HINGE : Inspec-
8.
Install center pillar lower garnish. Refer to
INT-18, "Removal and Installation"
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000010478255
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse mounting TORX bolt. Always replace it with a new one when it is removed.
• Check rear door open/close, lock/unlock operation after installation.
• After installation, be sure to perform the fitting adjustment. Refer to
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000010478256
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
: N·m (kg-m, ft-lb)
: Body grease
Portion
Standard
Front door – Rear door
B – B
J
Clearance
3.3 – 5.3
[0.130 – 0.209]
K
Surface
height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
Rear door – Body side panel
C – C
L
Clearance
3.5 – 5.5
[0.138 – 0.217]
M
Surface
height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
DLK-352
< REMOVAL AND INSTALLATION >
[TYPE 2]
REAR DOOR
• When removing and installing rear door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove rear door assembly. Refer to
DLK-349, "DOOR ASSEMBLY : Removal and Installation"
2.
Remove door hinge mounting bolts of vehicle body side, and then remove door hinge (lower).
3.
Remove center pillar lower garnish. Refer to
INT-18, "Removal and Installation"
.
4.
Remove door hinge mounting nuts of vehicle body side, and then remove door hinge (upper).
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check front door open/close, lock/unlock operation after installation.
• After installation, perform the fitting adjustment. Refer to
DLK-345, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• After installation, check door hinge rotating part for poor lubrication. Refer to
DOOR HINGE : Inspection
INFOID:0000000010478257
Check door hinge rotating part for poor lubrication. Apply body grease if necessary.
• Door hinge (upper)
• Door hinge (lower)
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000010478258
REMOVAL
1.
Fully close the rear door glass.
2.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Removal and Installation"
.
3.
Remove rear door speaker.
a.
Disconnect rear door speaker harness connector.
b.
Remove rear door speaker mounting bolts, and then remove rear door speaker.
4.
Remove check link mounting bolts of vehicle body side.
: Body grease
JMKIB0329ZZ
: Body grease
JMKIB0321ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст