Qashqai J11. Door & Lock — part 10
FRONT FENDER
DLK-161
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT FENDER
Exploded View
INFOID:0000000010434689
Removal and Installation
INFOID:0000000010434690
CAUTION:
Use protective tape or shop cloth to protect from damage during removal and installation.
REMOVAL
1.
Remove fillet molding. Refer to
EXT-38, "Removal and Installation"
2.
Remove fender protector. Refer to
EXT-33, "Removal and Installation"
3.
Remove front bumper fascia assembly and bumper side bracket. Refer to
EXT-20, "Removal and Installa-
4.
Remove front combination lamp. Refer to
EXL-319, "Removal and Installation"
EXL-162, "Removal and Installation"
(LED HEADLAMP).
5.
Remove front fender seal.
6.
Remove front fender assembly mounting bolts.
1.
Front fender seal
2.
Front fender assembly
3.
Hoodledge cover
: Pawl
: N·m (kg-m, in-lb)
JMKIB3315GB
DLK-162
< REMOVAL AND INSTALLATION >
[TYPE 1]
FRONT FENDER
7.
Remove front fender stiffener (2) from the vehicle body while
carefully pulling upper portion of front fender (1) toward vehicle
outside.
8.
Remove front fender assembly.
CAUTION:
An viscous urethane foam is installed on the back surface of front fender. When removing the
front fender, be careful to not deform the front fender while performing the procedure and remov-
ing the viscous urethane foam a little at a time.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• After installation, apply the touch-up paint (the body color) onto the head of front fender mounting
bolts.
• After installation, adjust the following part.
- Hood assembly: Refer to
DLK-152, "HOOD ASSEMBLY : Adjustment"
.
- Front door: Refer to
DLK-164, "DOOR ASSEMBLY : Adjustment"
: Vehicle front
JMKIA5633ZZ
FRONT DOOR
DLK-163
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT DOOR
Exploded View
INFOID:0000000010434692
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000010434693
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove front door harness grommet from vehicle body side, and then pull out front door harness.
2.
Disconnect front door harness connector.
3.
Remove mounting bolt of door check link on the vehicle body.
4.
Remove door hinge mounting nuts of door side, and then remove door assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
1.
Front door panel
2.
Door hinge (upper)
3.
Door hinge (lower)
4.
Door check link
5.
Bumper rubber
6.
Door striker
7.
TORX bolt
8.
Grommet
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Body grease
JMKIB3247GB
DLK-164
< REMOVAL AND INSTALLATION >
[TYPE 1]
FRONT DOOR
• Apply anticorrosive agent onto the mounting surface.
• After installation, perform the fitting adjustment. Refer to
DLK-164, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• Check door hinge and door check link rotating part for poor lubrication.
- Door hinge: Refer to
DLK-166, "DOOR HINGE : Inspection"
.
- Door check link: Refer to
DLK-166, "DOOR CHECK LINK : Removal and Installation"
.
DOOR ASSEMBLY : Adjustment
INFOID:0000000010434694
FITTING ADJUSTMENT
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
TORX bolt
7.
Front door hinge
8.
Rear door hinge (upper)
9.
Rear door hinge (lower)
: Always replace after every disassembly.
JMKIB3256GB
FRONT DOOR
DLK-165
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Fitting Adjustment Standard
Check the clearance and surface height between front door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm [in]
Fitting Adjustment Procedure
1.
Remove front fender. Refer to
DLK-161, "Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
3.
Adjust the surface height of front door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting bolts on vehicle body side.
6.
Raise front door at rear end to adjust clearance of the front door according to the fitting standard dimen-
sion.
7.
After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• After installation, apply touch-up paint (the body color) onto the head of hinge mounting bolts
and nuts.
• Check door hinge rotating part for poor lubrication. Apply body grease if necessary. Refer to
DLK-166, "DOOR HINGE : Inspection"
8.
Install front fender. Refer to refer to
DLK-161, "Removal and Installation"
.
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000010434695
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse mounting TORX bolt. Always replace it with a new one when it is removed.
• Check front door open/close, lock/unlock operation after installation.
• After installation, perform the fitting adjustment. Refer to
DLK-164, "DOOR ASSEMBLY : Adjust-
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000010434696
REMOVAL
: N·m (kg-m, ft-lb)
: Body grease
Portion
Standard
Front fender – Front door
A – A
H
Clearance
3.3 – 5.3
[0.130 – 0.209]
I
Surface
height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
Front door – Rear door
B – B
J
Clearance
3.3 – 5.3
[0.130 – 0.209]
K
Surface
height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
DLK-166
< REMOVAL AND INSTALLATION >
[TYPE 1]
FRONT DOOR
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
1.
Remove front fender. Refer to
DLK-161, "Removal and Installation"
2.
Remove front door assembly. Refer to
DLK-163, "DOOR ASSEMBLY : Removal and Installation"
.
3.
Remove front door hinge mounting bolts (body side), and then remove front door hinge.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check front door open/close, lock/unlock operation after installation.
• After installation, perform the fitting adjustment. Refer to
DLK-164, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• After installation, check door hinge rotating part for poor lubrication. Refer to
DOOR HINGE : Inspection
INFOID:0000000010434697
Check door hinge rotating part for poor lubrication. Apply body
grease if necessary.
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000010434698
REMOVAL
1.
Fully close the front door glass.
2.
Remove front door finisher. Refer to
INT-12, "FRONT DOOR FINISHER : Removal and Installation"
.
3.
Remove front door speaker.
a.
Disconnect front door speaker harness connector.
b.
Remove front door speaker mounting bolts, and then remove front door speaker.
4.
Remove check link mounting bolts of vehicle body side.
5.
Remove check link mounting bolts of door side.
6.
Take door check link out from the hole of door panel.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check front door open/close operation after installation.
• After installation, check door check link rotating part for poor lubrication. Refer to
: Body grease
JMKIB0321ZZ
FRONT DOOR
DLK-167
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR CHECK LINK : Inspection
INFOID:0000000010434699
Check door hinge rotating part for poor lubrication. Apply body
grease if necessary.
: Body grease
JMKIB0322ZZ
DLK-168
< REMOVAL AND INSTALLATION >
[TYPE 1]
REAR DOOR
REAR DOOR
Exploded View
INFOID:0000000010434701
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000010434702
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing rear door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove rear door harness grommet from vehicle body side, and then pull out rear door harness.
2.
Disconnect rear door harness connector.
3.
Remove mounting bolt of door check link on the vehicle.
4.
Remove door hinge mounting nuts of door side, and then remove rear door assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
1.
Rear door panel
2.
Door hinge (upper)
3.
Door hinge (lower)
4.
Door check link
5.
Door striker
6.
TORX bolt
7.
Grommet
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Body grease
JMKIB3249GB
REAR DOOR
DLK-169
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Apply anticorrosive agent onto the mounting surface.
• After installation, perform the fitting adjustment. Refer to
DLK-169, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• Check door hinge and door check link rotating part for poor lubrication.
- Door hinge: Refer to
DLK-171, "DOOR HINGE : Inspection"
.
- Door check link: Refer to
DLK-172, "DOOR CHECK LINK : Inspection"
.
DOOR ASSEMBLY : Adjustment
INFOID:0000000010434703
FITTING ADJUSTMENT
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
TORX bolt
7.
Front door hinge
8.
Rear door hinge (upper)
9.
Rear door hinge (lower)
: Always replace after every disassembly.
JMKIB3256GB
DLK-170
< REMOVAL AND INSTALLATION >
[TYPE 1]
REAR DOOR
Fitting Adjustment Standard
Check the clearance and surface height between rear door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm [in]
Fitting Adjustment Procedure
1.
Remove center pillar lower garnish. Refer to
INT-18, "Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
3.
Adjust the surface height of rear door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting nuts and bolts on body side.
6.
Raise rear door at rear end to adjust clearance of rear door according to the fitting standard dimension.
7.
After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• After installation, apply touch-up paint (the body color) onto the head of hinge mounting bolts
and nuts.
• Check door hinge rotating part for poor lubrication. Refer to
DLK-166, "DOOR HINGE : Inspec-
8.
Install center pillar lower garnish. Refer to
INT-18, "Removal and Installation"
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000010434704
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse mounting TORX bolt. Always replace it with a new one when it is removed.
• Check rear door open/close, lock/unlock operation after installation.
• After installation, be sure to perform the fitting adjustment. Refer to
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000010434705
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
: N·m (kg-m, ft-lb)
: Body grease
Portion
Standard
Front door – Rear door
B – B
J
Clearance
3.3 – 5.3
[0.130 – 0.209]
K
Surface
height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
Rear door – Body side panel
C – C
L
Clearance
3.5 – 5.5
[0.138 – 0.217]
M
Surface
height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
REAR DOOR
DLK-171
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• When removing and installing rear door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove rear door assembly. Refer to
DLK-168, "DOOR ASSEMBLY : Removal and Installation"
2.
Remove door hinge mounting bolts of vehicle body side, and then remove door hinge (lower).
3.
Remove center pillar lower garnish. Refer to
INT-18, "Removal and Installation"
.
4.
Remove door hinge mounting nuts of vehicle body side, and then remove door hinge (upper).
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check front door open/close, lock/unlock operation after installation.
• After installation, perform the fitting adjustment. Refer to
DLK-164, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• After installation, check door hinge rotating part for poor lubrication. Refer to
DOOR HINGE : Inspection
INFOID:0000000010434706
Check door hinge rotating part for poor lubrication. Apply body grease if necessary.
• Door hinge (upper)
• Door hinge (lower)
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000010434707
REMOVAL
1.
Fully close the rear door glass.
2.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Removal and Installation"
3.
Remove rear door speaker.
a.
Disconnect rear door speaker harness connector.
b.
Remove rear door speaker mounting bolts, and then remove rear door speaker.
4.
Remove check link mounting bolts of vehicle body side.
: Body grease
JMKIB0329ZZ
: Body grease
JMKIB0321ZZ
DLK-172
< REMOVAL AND INSTALLATION >
[TYPE 1]
REAR DOOR
5.
Remove check link mounting bolts of door side.
6.
Take door check link out from the hole of door panel.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check front door open/close operation after installation.
• After installation, check door check link rotating part for poor lubrication. Refer to
DOOR CHECK LINK : Inspection
INFOID:0000000010434708
Check door hinge rotating part for poor lubrication. Apply body
grease if necessary.
: Body grease
JMKIB0322ZZ
BACK DOOR
DLK-173
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR
Exploded View
INFOID:0000000010434710
BACK DOOR ASSEMBLY
BACK DOOR ASSEMBLY : Removal and Installation
INFOID:0000000010434711
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• Use protective tape or shop cloth to protect from damage during removal and installation.
1.
Back door hinge
2.
Stud ball
3.
Back door stay
4.
Back door weather-strip
5.
Stud ball
6.
Back door bumper rubber
7.
Back door striker
8.
TORX bolt
9.
Back door panel
A.
Center mark
B.
Seam
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
,
,
,
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB3637GB
DLK-174
< REMOVAL AND INSTALLATION >
[TYPE 1]
BACK DOOR
REMOVAL
1.
Remove back door trim finisher lower and back door trim finisher upper. Refer to
.
2.
Remove rear washer tube from back door panel. Refer to
WW-90, "WASHER TUBE : Removal and Instal-
.
3.
Disconnect back door harness connectors from body harness connectors.
4.
Remove harness grommet from back door panel.
5.
Pull out body harness LH from back door panel.
6.
Support back door with the proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the back door open when removing the
back door stay.
7.
Remove back door stay of back door side. Refer to
DLK-177, "BACK DOOR STAY : Removal and Installa-
8.
Remove back door mounting nuts, and then remove back door assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• After installation, perform the fitting adjustment. Refer to
DLK-174, "BACK DOOR ASSEMBLY :
• Apply touch-up paint to the body color if the paint around back door hinge is peeled off.
• Check back door hinge rotating part for poor lubrication. Refer to
BACK DOOR ASSEMBLY : Adjustment
INFOID:0000000010434712
FITTING ADJUSTMENT
BACK DOOR
DLK-175
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Fitting Adjustment Standard
Check the clearance and the surface height between back door and each part by seeing and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
1.
Roof panel
2.
Body side outer
3.
Rear bumper fascia
4.
Back door panel
5.
Back door hinge
6.
Back door bumper rubber
7.
Back door striker
8.
TORX bolt
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Body grease
JMKIB3321GB
DLK-176
< REMOVAL AND INSTALLATION >
[TYPE 1]
BACK DOOR
Unit: mm [in]
Fitting Adjustment Procedure
1.
Loosen back door striker mounting TORX bolts.
2.
Loosen back door hinge mounting nuts (back door side).
3.
Adjust back door using back door striker, back door hinge and back door bumper rubber to the specified
value, as shown in the following table.
4.
After adjustment tighten back door striker mounting bolts and back door hinge mounting nuts (back door
side) to the specified torque.
CAUTION:
• Apply touch-up paint to the body color if the paint around back door hinge, and back door hinge
mounting nuts is peeled off.
• Check back door hinge rotating part for poor lubrication. Refer to
BACK DOOR STRIKER ADJUSTMENT
Adjust back door striker so that it becomes parallel with back door lock insertion direction.
BACK DOOR STRIKER
BACK DOOR STRIKER : Removal and Installation
INFOID:0000000010434713
REMOVAL
1.
Remove luggage rear plate. Refer to
2.
Remove TORX bolts, and then remove back door striker.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse mounting TORX bolt. Always replace it with a new one when it is removed.
• After installation, perform the fitting adjustment. Refer to
DLK-174, "BACK DOOR ASSEMBLY :
• After installation, check back door open/close, lock/unlock operation.
BACK DOOR HINGE
BACK DOOR HINGE : Removal and Installation
INFOID:0000000010434714
REMOVAL
1.
Remove back door assembly. Refer to
DLK-173, "BACK DOOR ASSEMBLY : Removal and Installation"
2.
Remove luggage side upper finisher LH and RH. Refer to
.
3.
Lower the rear end of headlining to secure work space.
4.
Remove back door hinge mounting nut, and then remove back door hinge.
INSTALLATION
Portion
Standard
Difference
(RH/LH,MAX)
Back door – Roof panel
A – A
D
Clearance
5.0 – 7.0
[0.197 – 0.276]
—
E
Surface
height
0 – 2.0
[0 – 0.079]
—
Back door – Body side outer
B – B
F
Clearance
2.8 – 7.2
[0.110 – 0.283]
< 2.9
[0.114]
G
Surface
height
0 – 4.0
[0 – 0.157]
< 2.5
[0.098]
Back door – Rear bumper fascia
C – C
H
Clearance
4.8 – 9.2
[0.189 – 0.362]
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст