Qashqai J11. Door & Lock — part 11
BACK DOOR
DLK-177
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check back door hinge rotating part for poor lubrication. Refer to
• After installation, perform the fitting adjustment. Refer to
DLK-174, "BACK DOOR ASSEMBLY :
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
BACK DOOR HINGE : Inspection
INFOID:0000000010434715
Check door hinge rotating part for poor lubrication. Apply body
grease if necessary.
BACK DOOR STAY
BACK DOOR STAY : Removal and Installation
INFOID:0000000010434716
REMOVAL
1.
Support the back door with the suitable material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the back door open when removing the
back door stay.
CAUTION:
Use protective tape or shop cloth to protect from damage during removal and installation.
2.
Remove back door stay of vehicle body side.
a.
Remove the metal clip (3) located on the connection between
the back door stay (1) and the stud ball (2) by using a remover
tool (A) according to the numerical order 1
→
2 indicated by
arrows as shown in the figure.
b.
Disengage back door stay from stud ball.
3.
Remove back door stay mounting bolts of back door side, and then remove back door stay.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• After installation, check back door open/close, lock/unlock operation.
BACK DOOR STAY : Disposal
INFOID:0000000010434717
CAUTION:
When performing disposal operation, wear the protective glasses and protective gloves.
: Body grease
JMKIB0628ZZ
JMKIA2255ZZ
DLK-178
< REMOVAL AND INSTALLATION >
[TYPE 1]
BACK DOOR
1.
Fix back door stay (1) using a vise (C)
CAUTION:
When cutting a hole on back door stay, always cover a
hacksaw (A) using a shop cloth (B) to avoid scattering
metal fragments or oil.
2.
Slowly cut a hole and drain the gas in the order of 1
→
2 as
shown in the figure using a hacksaw at 2 positions of (1) and (2).
BACK DOOR WEATHER-STRIP
BACK DOOR WEATHER-STRIP : Removal and Installation
INFOID:0000000010434718
REMOVAL
Pull up and remove engagement with body from weather-strip joint.
CAUTION:
Never pull strongly on weather-strip.
INSTALLATION
1.
Working from the upper section, align weather-strip center mark with vehicle center position mark and
install weather-strip onto the vehicle.
2.
For the lower section, align the weather-strip seam with center of back door striker.
3.
Pull weather-strip gently to ensure that there is no loose section.
CAUTION:
Securely fit each corner.
JMKIA3336ZZ
A
: 20 mm (0.787 in)
B
: Cat at the groove
JMKIA3609ZZ
HOOD LOCK
DLK-179
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HOOD LOCK
Exploded View
INFOID:0000000010434719
HOOD LOCK
HOOD LOCK : Removal and Installation
INFOID:0000000010434720
REMOVAL
1.
Remove front grille. Refer to
EXT-26, "Removal and Installation"
2.
Remove hood lock assembly mounting bolt and nuts, and then remove hood lock assembly from radiator
core support upper.
3.
Disconnect hood lock control cable assembly from hood lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never bend cable too much, keeping the radius 100 mm (3.937 in) or more.
• After installation, perform hood lock control inspection. Refer to
.
1.
Hood lock control handle
2.
Hood lock control cable
3.
Hood safety hook
4.
Hood lock assembly
: Clip
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Body grease
JMKIB3308GB
DLK-180
< REMOVAL AND INSTALLATION >
[TYPE 1]
HOOD LOCK
• Check hood lock assembly for poor lubrication. Refer to
• After installation, perform hood fitting adjustment. Refer to
DLK-152, "HOOD ASSEMBLY : Adjust-
HOOD LOCK CONTROL HANDLE
HOOD LOCK CONTROL HANDLE : Removal and Installation
INFOID:0000000010434722
REMOVAL
1.
Remove hood lock control handle mounting bolts, and then remove hood lock control handle.
2.
Disconnect hood lock control cable (2) from hood opener lever
(1) according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
3.
Disconnect fuel opener cable from fuel filler lid opener lever of hood lock control handle. Refer to
194, "FUEL FILLER OPENER CABLE : Removal and Installation"
.
INSTALLATION
Install in the reverse order of removal.
HOOD LOCK CONTROL CABLE
HOOD LOCK CONTROL CABLE : Removal and Installation
INFOID:0000000010434721
REMOVAL
1.
Disconnect hood lock control cable from hood lock assembly. Refer to
2.
Remove fender protector (driver side). Refer to
EXT-33, "Removal and Installation"
3.
Remove hood lock control cable fixing clips.
4.
Disconnect hood lock control cable from hood lock control handle. Refer to
CONTROL HANDLE : Removal and Installation"
.
5.
Remove grommet on the lower dash, and pull the hood lock control cable toward the passenger compart-
ment.
CAUTION:
While pulling, never damage (peeling) the outside of hood lock control cable.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never bend cable too much, keeping the radius 100 mm (3.937 in) or more.
• Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet (at * mark) properly.
JMKIB0327ZZ
PIIB5801E
HOOD LOCK
DLK-181
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• After installation, perform hood fitting adjustment. Refer to
DLK-152, "HOOD ASSEMBLY : Adjust-
• After installation, perform hood lock control inspection. Refer to
.
HOOD SAFETY HOOK
HOOD SAFETY HOOK : Removal and Installation
INFOID:0000000010478165
REMOVAL
Remove mounting nuts, and then remove hood lock secondary assembly.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, perform hood lock control inspection. Refer to
.
Inspection
INFOID:0000000010434723
NOTE:
If the hood lock cable is bent or deformed, replace it.
1.
Check that hood opener operating is condition 49 N (5.0 kg, 11.0 lb) or below.
2.
Check that secondary latch is securely engaged with secondary striker from the dead load of the hood
assembly.
3.
Check that primary latch is securely engaged with primary striker when hood assembly is closed [free-fall
from approximately 200 mm (7.874 in) height].
CAUTION:
Never free-fall hood assembly from a height of 300 (11.811 in) mm or more.
4.
While operating hood opener, carefully check that the front end of hood is raised by approximately 20.0
mm (0.787 in). Also check that hood opener returns to the original position.
5.
Check that secondary latch is properly engaged with secondary striker [4.0 mm (0.157 in)].
6.
Check the hood lock lubrication condition. If necessary, apply
body grease to hood lock assembly.
: Body grease
JMKIB1164ZZ
DLK-182
< REMOVAL AND INSTALLATION >
[TYPE 1]
FRONT DOOR LOCK
FRONT DOOR LOCK
Exploded View
INFOID:0000000010434724
*
1
: Driver side only
1.
Outside handle escutcheon
2.
Outside handle grip
3.
Front gasket
4.
Inside handle
5.
cable clip
6.
Door lock assembly
7.
Key rod protector*
1
8.
Key rod*
1
9.
TORX bolt
10. Outside handle bracket
11. Rear gasket
: Pawl
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
JMKIB3252GB
FRONT DOOR LOCK
DLK-183
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000010434725
REMOVAL
1.
Disconnect inside handle cable from inside handle. Refer to
DLK-183, "INSIDE HANDLE : Removal and
.
2.
Disconnect outside handle cable from outside handle bracket. Refer to
.
3.
Disconnect door lock assembly harness connector.
4.
Remove door lock assembly screws, and then remove door lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse door lock assembly screw. Always replace it with a new one when it is removed.
• Check door lock cable is properly engaged with outside handle bracket.
• When installing key rod, rotate key rod holder until a click is felt.
• Check door lock assembly for poor lubrication. Refer to
DLK-183, "DOOR LOCK : Inspection"
• Check door open/close, lock/unlock operation after installation.
DOOR LOCK : Inspection
INFOID:0000000010434726
Check door lock assembly for poor lubrication. Apply body grease if
necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000010434727
REMOVAL
1.
Remove front door finisher. Refer to
INT-12, "FRONT DOOR FINISHER : Removal and Installation"
.
2.
Remove inside handle mounting bolt.
3.
Disengage inside handle from door panel while sliding inside handle toward vehicle rear, and then sepa-
rate inside handle.
4.
Disconnect inside handle cable, and then remove inside handle.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000010434728
REMOVAL
1.
Fully close the front door glass.
2.
Remove front door finisher. Refer to
INT-12, "FRONT DOOR FINISHER : Removal and Installation"
.
3.
Remove sealing screen.
: Body grease
JMKIA8534ZZ
DLK-184
< REMOVAL AND INSTALLATION >
[TYPE 1]
FRONT DOOR LOCK
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
4.
Remove front door glass rear run. Refer to
GW-23, "Removal and Installation"
.
5.
Remove key rod protector mounting bolts, and then remove key rod protector.
6.
Disengage outside handle cable from cable clip.
7.
Disengage rod holder, and then disconnect key rod from door lock assembly. (Driver side only)
8.
Disconnect outside handle harness connector.
9.
Remove grommet (1) of door side. Loosen, through grommet hole, TORX bolt (2) that fixes outside handle
escutcheon.
10. While pulling outside handle (1)according to the numerical order
1
→
2 indicated by arrows as shown in the figure, remove outside
handle escutcheon (2).
11. While pulling outside handle (1) according to the numerical order
1
→
2 indicated by arrows as shown in the figure, slide toward
rear of vehicle to remove outside handle.
12. Remove front gasket (1) and rear gasket (2).
JMKIB0585ZZ
JMKIA0441ZZ
JMKIA2948ZZ
JMKIB2240ZZ
FRONT DOOR LOCK
DLK-185
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
13. Slide outside handle bracket toward rear of vehicle to remove.
14. Disconnect outside handle cable (1) from outside handle bracket
(2) according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
CAUTION:
Never bend the outside handle cable end.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When installing key rod, rotate key rod holder until a click is felt.
• Check that door lock cables are normally engaged with inside handle and outside handle.
• After installation, check door open/close, and lock/unlock operation.
: Pawl
: Vehicle front
: Vehicle front
JMKIA5935ZZ
JMKIA5936ZZ
DLK-186
< REMOVAL AND INSTALLATION >
[TYPE 1]
REAR DOOR LOCK
REAR DOOR LOCK
Exploded View
INFOID:0000000010434729
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000010434730
REMOVAL
1.
Remove inside handle. Refer to
DLK-187, "INSIDE HANDLE : Removal and Installation"
.
2.
Remove outside handle bracket. Refer to
DLK-187, "OUTSIDE HANDLE : Removal and Installation"
1.
Outside handle escutcheon
2.
Outside handle grip
3.
Front gasket
4.
Cable clip
5.
Inside handle
6.
Door lock assembly
7.
TORX bolt
8.
Outside handle bracket
9.
Rear gasket
: Pawl
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
JMKIB3254GB
REAR DOOR LOCK
DLK-187
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Remove rear door lower sash mounting bolt, and then remove rear door lower sash.
4.
Disconnect door lock assembly harness connector.
5.
Remove door lock assembly screws, and then remove door lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse door lock assembly screw. Always replace it with a new one when it is removed.
• Check door lock cable is properly engaged with outside handle bracket.
• Check door lock assembly for poor lubrication. Refer to
DLK-187, "DOOR LOCK : Inspection"
• Check door open/close, lock/unlock operation after installation.
DOOR LOCK : Inspection
INFOID:0000000010434731
Check door lock assembly for poor lubrication. Apply body grease if
necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000010434732
REMOVAL
1.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Removal and Installation"
2.
Remove inside handle mounting bolt.
3.
Disengage inside handle from door panel while sliding inside handle toward vehicle rear, and then sepa-
rate inside handle.
4.
Disconnect inside handle cable, and then remove inside handle.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000010434733
REMOVAL
1.
Fully close the rear door glass.
2.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Removal and Installation"
3.
Remove sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
: Body grease
JMKIA8534ZZ
DLK-188
< REMOVAL AND INSTALLATION >
[TYPE 1]
REAR DOOR LOCK
4.
Remove grommet (1) of door side. Loosen, through grommet hole, TORX bolt (2) that fixes outside handle
escutcheon.
5.
While pulling outside handle (1) according to the numerical order
1
→
2 indicated by arrows as shown in the figure, remove outside
handle escutcheon (2).
6.
While pulling outside handle (1) according to the numerical order
1
→
2 indicated by arrows as shown in the figure, slide toward
rear of vehicle to remove outside handle.
7.
Remove front gasket (1) and rear gasket (2).
JMKIB0588ZZ
JMKIA9526ZZ
JMKIA2948ZZ
: Pawl
: Vehicle front
JMKIB2240ZZ
REAR DOOR LOCK
DLK-189
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
8.
Slide outside handle bracket toward rear of vehicle to remove.
9.
Disconnect outside handle cable (1) from outside handle bracket
(2) according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
CAUTION:
Never bend the outside handle cable end.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check that door lock cables are normally engaged with inside handle and outside handle.
• After installation, check door open/close, and lock/unlock operation.
: Vehicle front
JMKIA5935ZZ
JMKIA5936ZZ
DLK-190
< REMOVAL AND INSTALLATION >
[TYPE 1]
BACK DOOR LOCK
BACK DOOR LOCK
Exploded View
INFOID:0000000010434734
Removal and Installation
INFOID:0000000010434735
REMOVAL
1.
Remove back door trim finisher lower. Refer to
INT-31, "Removal and Installation"
2.
Disconnect back door lock harness connector.
3.
Remove back door assembly mounting bolts, and then remove back door lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• After installation, check back door open/close, and lock/unlock operation.
• Check door lock assembly for poor lubrication. Refer to
1.
Back door panel
2.
Back door lock assembly
: N·m (kg-m, ft-lb)
: Body grease
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB3271GB
BACK DOOR LOCK
DLK-191
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Inspection
INFOID:0000000010434736
Check door lock assembly for poor lubrication. Apply body grease if
necessary.
: Body grease
JMKIB0629ZZ
DLK-192
< REMOVAL AND INSTALLATION >
[TYPE 1]
FUEL FILLER LID OPENER
FUEL FILLER LID OPENER
Exploded View
INFOID:0000000010434739
FUEL FILLER LID
FUEL FILLER LID : Removal and Installation
INFOID:0000000010434740
REMOVAL
1.
Fully open fuel filler lid assembly.
1.
Fuel opener cable
2.
Cable protector
3.
Fuel filler lid lock assembly
4.
Bumper rubber
5.
Fuel filler lid assembly
6.
Fuel filler spring
: Clip
: Pawl
: Always replace after every disassembly.
JMKIB3263ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст