Qashqai J11. Door & Lock — part 18
HAZARD FUNCTION
DLK-289
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HAZARD FUNCTION
Component Function Check
INFOID:0000000010487312
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “FLASHER” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Hazard warning lamp circuit is OK.
NO
>> Refer to
DLK-289, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010487313
1.
CHECK HAZARD OPERATION
EXL-26, "TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Description"
(LED
headlamp models) or
EXL-195, "TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Descrip-
(halogen headlamp models).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
(LED headlamp models) and
(halogen headlamp models).
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Monitor item
Status
FLASHER
LH
Front turn signal lamp LH
Turns ON
RH
Front turn signal lamp RH
Turns ON
OFF
Front turn signal lamp
Turns OFF
DLK-290
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
INFORMATION DISPLAY
INFORMATION DISPLAY
Diagnosis Procedure
INFOID:0000000010487314
1.
CHECK COMBINATION METER
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
INTELLIGENT KEY BATTERY
DLK-291
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTELLIGENT KEY BATTERY
Component Inspection
INFOID:0000000010487315
1.
CHECK INTELLIGENT KEY BATTERY
Check by connecting a resistance (approximately 300
Ω
) so that the
current value becomes about 10 mA. Refer to
.
Is the measurement value within the specification?
YES
>> INSPECTION END
NO
>> Replace Intelligent Key battery.
Standard
: Approx. 2.5 - 3.0 V
OCC0607D
DLK-292
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
INTELLIGENT KEY WARNING BUZZER
INTELLIGENT KEY WARNING BUZZER
Component Function Check
INFOID:0000000010487316
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “OUTSIDE BUZZER” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Intelligent Key warning buzzer is OK.
NO
>> Refer to
DLK-292, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010487317
1.
CHECK INTELLIGENT KEY WARNING BUZZER POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect Intelligent Key warning buzzer connector.
3.
Check voltage between Intelligent Key warning buzzer harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK INTELLIGENT KEY WARNING BUZZER CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and Intelligent Key warning buzzer harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
Check continuity between Intelligent Key warning buzzer harness connector and ground.
Monitor item
Status
OUTSIDE BUZZER
ON
Outside warning buzzer
Buzzer sounds
OFF
Buzzer does not sound
(+)
(–)
Condition
Voltage
Intelligent Key warning buzzer
Connector
Terminal
E7
1
Ground
Operate Intelligent Key
buzzer
9 – 16 V
BCM
Intelligent Key warning buzzer
Continuity
Connector
Terminal
Connector
Terminal
E60
164
E7
1
Existed
BCM
Ground
Continuity
Connector
Terminal
E60
164
Not existed
INTELLIGENT KEY WARNING BUZZER
DLK-293
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace Intelligent Key warning buzzer.
NO
>> Repair or replace the malfunctioning parts.
Intelligent Key warning buzzer
Ground
Continuity
Connector
Terminal
E7
3
Existed
DLK-294
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
OUTSIDE KEY ANTENNA
OUTSIDE KEY ANTENNA
DRIVER SIDE
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000010487318
1.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1.
Turn ignition switch OFF.
2.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK OUTSIDE KEY ANTENNA CIRCUIT
1.
Disconnect BCM connector and front outside handle assembly (driver side) connector.
2.
Check continuity between BCM harness connector and front outside handle assembly (driver side) har-
ness connector.
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M69
100
Ground
When ignition switch
and any door switch is
ON
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
120
Ground
When ignition switch
and any door switch is
ON
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
JSMIA1348GB
JSMIA1406GB
JSMIA1507GB
JSMIA1506GB
OUTSIDE KEY ANTENNA
DLK-295
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
LHD models
RHD models
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 2
1.
Replace front outside handle assembly (driver side). (New antenna or other antenna)
2.
Connect BCM connector and front outside handle assembly (driver side) connector.
3.
Check signal between BCM harness connector and ground using oscilloscope.
BCM
Front outside handle assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M69
100
D8
1
Existed
120
2
BCM
Front outside handle assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M69
100
D39
1
Existed
120
2
BCM
Ground
Continuity
Connector
Terminal
M69
100
Not existed
120
DLK-296
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
OUTSIDE KEY ANTENNA
Is the inspection result normal?
YES
>> Replace outside handle grip RH.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
PASSENGER SIDE
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000010487319
1.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1.
Turn ignition switch OFF.
2.
Check signal between BCM harness connector and ground using oscilloscope.
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M69
100
Ground
When ignition switch
and any door switch is
ON
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
120
Ground
When ignition switch
and any door switch is
ON
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
JSMIA1348GB
JSMIA1406GB
JSMIA1507GB
JSMIA1506GB
OUTSIDE KEY ANTENNA
DLK-297
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK OUTSIDE KEY ANTENNA CIRCUIT
1.
Disconnect BCM connector and front outside handle assembly (passenger side) connector.
2.
Check continuity between BCM harness connector and front outside handle assembly (passenger side)
harness connector.
LHD models
RHD models
3.
Check continuity between BCM harness connector and ground.
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M69
118
Ground
When ignition switch
and any door switch is
ON
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
119
Ground
When ignition switch
and any door switch is
ON
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
JSMIA1507GB
JSMIA1506GB
JSMIA1507GB
JSMIA1506GB
BCM
Front outside handle assembly (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M69
118
D38
2
Existed
119
1
BCM
Front outside handle assembly (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M69
118
D9
2
Existed
119
1
DLK-298
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
OUTSIDE KEY ANTENNA
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 2
1.
Replace front outside handle assembly (passenger side). (New antenna or other antenna)
2.
Connect BCM connector and front outside handle assembly (passenger side) connector.
3.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace outside handle grip LH.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
REAR BUMPER
BCM
Ground
Continuity
Connector
Terminal
M69
118
Not existed
119
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M69
118
Ground
When ignition switch
and any door switch is
ON
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
119
Ground
When ignition switch
and any door switch is
ON
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
JSMIA1507GB
JSMIA1506GB
JSMIA1507GB
JSMIA1506GB
OUTSIDE KEY ANTENNA
DLK-299
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR BUMPER : Diagnosis Procedure
INFOID:0000000010487320
1.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1.
Turn ignition switch OFF.
2.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK OUTSIDE KEY ANTENNA CIRCUIT
1.
Disconnect BCM connector and outside key antenna (rear bumper) connector.
2.
Check continuity between BCM harness connector and outside key antenna (rear bumper) harness con-
nector.
3.
Check continuity between BCM harness connector and ground.
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
B4
21
Ground
When ignition switch
and any door switch is
ON
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
24
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
JMMIA1652GB
JMMIA1653GB
JSMIA1507GB
JSMIA1506GB
BCM
Outside key antenna (rear bumper)
Continuity
Connector
Terminal
Connector
Terminal
B4
21
B52
2
Existed
24
1
DLK-300
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
OUTSIDE KEY ANTENNA
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 2
1.
Replace outside key antenna (rear bumper). (New antenna or other antenna)
2.
Connect BCM and outside key antenna (rear bumper) connector.
3.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace outside key antenna (rear bumper).
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
BCM
Ground
Continuity
Connector
Terminal
B4
21
Not existed
24
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
B4
21
Ground
When ignition switch
and any door switch is
ON
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
24
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
JMMIA1652GB
JMMIA1653GB
JSMIA1507GB
JSMIA1506GB
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
DLK-301
< SYMPTOM DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SYMPTOM DIAGNOSIS
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK
SWITCH
ALL DOOR
ALL DOOR : Description
INFOID:0000000010488224
All doors do not lock/unlock using door lock and unlock switch.
ALL DOOR : Diagnosis Procedure
INFOID:0000000010488225
1.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check front door lock and unlock power supply and ground circuit.
Refer to
DLK-110, "FRONT DOOR : Diagnosis Procedure"
(front door) or
DLK-110, "REAR DOOR : Diagnosis
(rear door).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK DOOR LOCK AND UNLOCK SWITCH
Check door lock and unlock switch.
Refer to
DLK-89, "DRIVER SIDE : Component Function Check"
(passenger side).
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK DOOR LOCK ACTUATOR
Check front door lock assembly (driver side).
Refer to
DLK-84, "DRIVER SIDE : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-95, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
FRONT DOOR
FRONT DOOR : Description
INFOID:0000000010488226
Front doors do not lock/unlock using door lock and unlock switch.
FRONT DOOR : Diagnosis Procedure
INFOID:0000000010488227
1.
CHECK POWER SUPPLY AND GROUND CIRCUIT
DLK-302
< SYMPTOM DIAGNOSIS >
[TYPE 2]
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
Check front door lock and unlock power supply and ground circuit.
Refer to
DLK-110, "FRONT DOOR : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK DOOR LOCK ACTUATOR
Check front door lock actuator (driver side).
Refer to
DLK-273, "DRIVER SIDE : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
REAR DOOR
REAR DOOR : Description
INFOID:0000000010488228
Rear doors do not lock/unlock using door lock and unlock switch.
REAR DOOR : Diagnosis Procedure
INFOID:0000000010488229
1.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check rear doors lock and unlock power supply and ground circuit.
Refer to
DLK-110, "REAR DOOR : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK DOOR LOCK ACTUATOR
Check rear door lock actuator.
Refer to
DLK-86, "REAR LH : Component Function Check"
(RH).
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000010488230
Driver side door does not lock/unlock using door lock and unlock switch.
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000010488231
1.
CHECK DOOR LOCK ACTUATOR
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
DLK-303
< SYMPTOM DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Check front door lock assembly (driver side).
Refer to
DLK-84, "DRIVER SIDE : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
PASSENGER SIDE
PASSENGER SIDE : Description
INFOID:0000000010488232
Passenger side door does not lock/unlock using door lock and unlock switch.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000010488233
1.
CHECK DOOR LOCK ACTUATOR
Check front door lock assembly (passenger side).
Refer to
DLK-85, "PASSENGER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
REAR LH
REAR LH : Description
INFOID:0000000010488234
Rear LH side door does not lock/unlock using door lock and unlock switch.
REAR LH : Diagnosis Procedure
INFOID:0000000010488235
1.
CHECK DOOR LOCK ACTUATOR
Check rear door lock assembly LH.
Refer to
DLK-86, "REAR LH : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
REAR RH
DLK-304
< SYMPTOM DIAGNOSIS >
[TYPE 2]
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
REAR RH : Description
INFOID:0000000010488236
Rear RH side door does not lock/unlock using door lock and unlock switch.
REAR RH : Diagnosis Procedure
INFOID:0000000010488237
1.
CHECK DOOR LOCK ACTUATOR
Check rear door lock assembly RH.
Refer to
DLK-87, "REAR RH : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст