Qashqai J11. Door & Lock — part 5
BACK DOOR REQUEST SWITCH
DLK-81
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR REQUEST SWITCH
Component Function Check
INFOID:0000000010479676
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “REQ SW-BD/TR” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Back door request switch is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000010479677
1.
CHECK BACK DOOR REQUEST SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect back door opener switch assembly connector.
3.
Check voltage between back door opener switch assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK BACK DOOR REQUEST SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and back door opener switch assembly harness con-
nector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair harness or connector.
3.
CHECK BACK DOOR REQUEST SWITCH GROUND CIRCUIT
Check continuity between back door opener switch assembly harness connector and ground.
Monitor item
Condition
Status
REQ SW-BD/TR
Back door request switch
Pressed
On
Released
Off
(+)
(–)
Voltage
Back door opener switch assembly
Connector
Terminal
D94
2
Ground
9 - 16 V
BCM
Back door opener switch assembly
Continuity
Connector
Terminal
Connector
Terminal
B4
6
D94
2
Existed
BCM
Ground
Continuity
Connector
Terminal
B4
6
Not existed
DLK-82
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
BACK DOOR REQUEST SWITCH
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK BACK DOOR REQUEST SWITCH
DLK-82, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace back door opener switch assembly.
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000010479678
1.
CHECK BACK DOOR REQUEST SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect back door opener switch assembly connector.
3.
Check continuity between back door opener switch assembly terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace back door opener switch assembly.
Back door opener switch assembly
Ground
Continuity
Connector
Terminal
D94
3
Existed
Back door opener switch assembly
Condition
Continuity
Terminal
2
3
Back door request switch
Pressed
Existed
Released
Not existed
COMBINATION METER BUZZER
DLK-83
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
COMBINATION METER BUZZER
Component Function Check
INFOID:0000000010434580
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “INSIDE BUZZER” in “ACTIVE TEST” mode.
3.
Touch “Buzzer 1”, “Buzzer 2” or “Buzzer 3” to check that it works normally.
Is the inspection result normal?
Yes
>> Buzzer (combination meter) is OK.
No
>> Refer to
.
Diagnosis Procedure
INFOID:0000000010434581
1.
CHECK METER BUZZER CIRCUIT
WCS-44, "Component Function Check"
.
Is the inspection result normal?
Yes
>> GO TO 2.
No
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
D L K -8 4
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
DOOR LOCK ACTUATOR
DOOR LOCK ACTUATOR
DRIVER SIDE
DRIVER SIDE : Component Function Check
INFOID:0000000010434582
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “DOOR LOCK” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-84, "DRIVER SIDE : Diagnosis Procedure"
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000010434583
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check voltage between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front door lock assembly (driver side).
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM connector and all door lock assembly connector.
2.
Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
Monitor item
Status
DOOR LOCK
ALL LOCK
Door lock actuators
LOCK
ALL UNLOCK
UNLOCK
(+)
(–)
Condition
Voltage
Front door lock assembly
(driver side)
Connector
Terminal
D26
2
Ground
Door lock and unlock switch
Unlock
9 – 16 V
3
Lock
BCM
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M68
141
D26
3
Existed
148
2
BCM
Ground
Continuity
Connector
Terminal
M68
141
Not existed
148
DOOR LOCK ACTUATOR
DLK-85
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
PASSENGER SIDE
PASSENGER SIDE : Component Function Check
INFOID:0000000010434584
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “DOOR LOCK” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-84, "DRIVER SIDE : Diagnosis Procedure"
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000010434585
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (passenger side) connector.
3.
Check voltage between front door lock assembly (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front door lock assembly (passenger side).
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM connector and all door lock assembly connector.
2.
Check continuity between BCM harness connector and front door lock assembly (passenger side) har-
ness connector.
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
M68
141
Ground
Door lock and unlock switch
Lock
9 – 16 V
148
Unlock
Monitor item
Status
DOOR LOCK
ALL LOCK
Door lock actuators
LOCK
ALL UNLOCK
UNLOCK
(+)
(–)
Condition
Voltage
Front door lock assembly
(passenger side)
Connector
Terminal
D2
2
Ground
Door lock and unlock switch
Unlock
9 – 16 V
3
Lock
DLK-86
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
DOOR LOCK ACTUATOR
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
REAR LH
REAR LH : Component Function Check
INFOID:0000000010434586
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “DOOR LOCK” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-84, "DRIVER SIDE : Diagnosis Procedure"
REAR LH : Diagnosis Procedure
INFOID:0000000010434587
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear door lock assembly LH connector.
3.
Check voltage between rear door lock assembly LH harness connector and ground.
BCM
Front door lock assembly (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M68
139
D2
2
Existed
141
3
BCM
Ground
Continuity
Connector
Terminal
M68
139
Not existed
141
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
M68
139
Ground
Door lock and unlock switch
Unlock
9 – 16 V
141
Lock
Monitor item
Status
DOOR LOCK
ALL LOCK
Door lock actuators
LOCK
ALL UNLOCK
UNLOCK
DOOR LOCK ACTUATOR
DLK-87
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> Replace rear door lock assembly LH.
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM connector and all door lock assembly connector.
2.
Check continuity between BCM harness connector and rear door lock assembly LH harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
REAR RH
REAR RH : Component Function Check
INFOID:0000000010434588
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “DOOR LOCK” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
(+)
(–)
Condition
Voltage
Rear door lock assembly LH
Connector
Terminal
D52
2
Ground
Door lock and unlock switch
Unlock
9 – 16 V
3
Lock
BCM
Rear door lock assembly LH
Continuity
Connector
Terminal
Connector
Terminal
B3
124
D52
2
Existed
125
3
BCM
Ground
Continuity
Connector
Terminal
B3
124
Not existed
125
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
B3
124
Ground
Door lock and unlock switch
Unlock
9 – 16 V
125
Lock
Monitor item
Status
DOOR LOCK
ALL LOCK
Door lock actuators
LOCK
ALL UNLOCK
UNLOCK
DLK-88
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
DOOR LOCK ACTUATOR
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-84, "DRIVER SIDE : Diagnosis Procedure"
REAR RH : Diagnosis Procedure
INFOID:0000000010434589
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear door lock assembly RH connector.
3.
Check voltage between rear door lock assembly RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear door lock assembly RH.
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM connector and all door lock assembly connector.
2.
Check continuity between BCM harness connector and rear door lock assembly RH harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
(+)
(–)
Condition
Voltage
Rear door lock assembly RH
Connector
Terminal
D65
2
Ground
Door lock and unlock switch
Unlock
9 – 16 V
3
Lock
BCM
Rear door lock assembly RH
Continuity
Connector
Terminal
Connector
Terminal
B3
124
D65
2
Existed
125
3
BCM
Ground
Continuity
Connector
Terminal
B3
124
Not existed
125
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
B3
124
Ground
Door lock and unlock switch
Unlock
9 – 16 V
125
Lock
DOOR LOCK AND UNLOCK SWITCH
DLK-89
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR LOCK AND UNLOCK SWITCH
DRIVER SIDE
DRIVER SIDE : Component Function Check
INFOID:0000000010434592
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “CDL LOCK SW”, “CDL UNLOCK SW” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock and unlock switch is OK.
NO
>> Refer to
DLK-89, "DRIVER SIDE : Diagnosis Procedure"
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000010434593
1.
CHECK DOOR LOCK AND UNLOCK SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector.
3.
Check signal between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR LOCK AND UNLOCK SWITCH CIRCUIT
1.
Disconnect BCM connector and front power window switch (passenger side) connector.
2.
Check continuity between BCM harness connector and power window main switch harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair or replace harness.
Monitor item
Condition
Status
CDL LOCK SW
Door lock and unlock switch
Lock
ON
Unlock
OFF
CDL UNLOCK SW
Lock
OFF
Unlock
ON
(+)
(–)
Voltage
Power window main switch
Connector
Terminal
D30
3
Ground
9 - 16 V
15
BCM
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
M70
50
D30
3
Existed
80
15
BCM
Ground
Continuity
Connector
Terminal
M70
50
Not existed
80
DLK-90
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
DOOR LOCK AND UNLOCK SWITCH
3.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-68, "POWER WINDOW MAIN SWITCH :
NO
>> INSPECTION END
PASSENGER SIDE
PASSENGER SIDE : Component Function Check
INFOID:0000000010479696
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “CDL LOCK SW”, “CDL UNLOCK SW” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock and unlock switch is OK.
NO
>> Refer to
DLK-90, "PASSENGER SIDE : Diagnosis Procedure"
.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000010479697
1.
CHECK DOOR LOCK AND UNLOCK SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front power window switch (passenger side) connector.
3.
Check signal between front power window switch (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR LOCK AND UNLOCK SWITCH CIRCUIT
1.
Disconnect BCM connector and power window main switch connector.
2.
Check continuity between BCM harness connector and front power window switch (passenger side) har-
ness connector.
3.
Check continuity between BCM harness connector and ground.
Monitor item
Condition
Status
CDL LOCK SW
Door lock and unlock switch
Lock
ON
Unlock
OFF
CDL UNLOCK SW
Lock
OFF
Unlock
ON
(+)
(–)
Voltage
Front power window switch (passenger side)
Connector
Terminal
D7
1
Ground
9 - 16 V
2
BCM
Front power window switch (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M70
50
D7
1
Existed
80
2
DOOR LOCK AND UNLOCK SWITCH
DLK-91
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace front power window switch (passenger side). Refer to
DOW SWITCH (PASSENGER SIDE) : Removal and Installation"
NO
>> INSPECTION END
BCM
Ground
Continuity
Connector
Terminal
M70
50
Not existed
80
DLK-92
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
DOOR LOCK STATUS INDICATOR
DOOR LOCK STATUS INDICATOR
Component Function Check
INFOID:0000000010434598
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “DOOR LOCK IND” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock status indicator is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000010434599
1.
CHECK DOOR LOCK STATUS INDICATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect indicator unit connector.
3.
Check voltage between indicator unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace indicator unit.
NO
>> GO TO 2.
2.
CHECK DOOR LOCK STATUS INDICATOR CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and indicator unit harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair or replace harness.
Monitor item
Status
DOOR LOCK IND
ON
Door lock status indicator
Turns ON
OFF
Turns OFF
(+)
(–)
Voltage
Indicator unit
Connector
Terminal
M4
5
Ground
9 – 16 V
BCM
Indicator unit
Continuity
Connector
Terminal
Connector
Terminal
M69
111
M4
5
Existed
BCM
Ground
Continuity
Connector
Terminal
M69
111
Not existed
DOOR REQUEST SWITCH
DLK-93
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR REQUEST SWITCH
Component Function Check
INFOID:0000000010434600
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “REQ SW-DR”, “REQ SW-AS” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Front door request switch is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000010434601
1.
CHECK DOOR REQUEST SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect malfunctioning front door request switch connector.
3.
Check voltage between malfunctioning front door request switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR REQUEST SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between malfunctioning front door request switch harness connector and BCM harness
connector.
3.
Check continuity between malfunctioning front door request switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair or replace harness.
Monitor item
Condition
Status
REQ SW -DR
Driver side door request switch
Pressed
ON
Released
OFF
REQ SW -AS
Passenger side door request switch
Pressed
ON
Released
OFF
(+)
(–)
Voltage
Front door request switch
Connector
Terminal
Driver side
D39
3
Ground
9 – 16 V
Passenger side
D9
Front door request switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
Driver side
D39
3
M69
105
Existed
Passenger side
D9
82
Front door request switch
Ground
Continuity
Connector
Terminal
Driver side
D39
3
Not existed
Passenger side
D9
DLK-94
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
DOOR REQUEST SWITCH
3.
CHECK DOOR REQUEST SWITCH GROUND CIRCUIT
Check continuity between malfunctioning front door request switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK DOOR REQUEST SWITCH
DLK-94, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace malfunctioning front door request switch.
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000010434602
1.
CHECK DOOR REQUEST SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect malfunctioning front door request switch connector.
3.
Check continuity between malfunctioning front door request switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace malfunctioning front door request switch.
Front door request switch
Ground
Continuity
Connector
Terminal
Driver side
D39
4
Existed
Passenger side
D9
Front door request switch
Condition
Continuity
Terminal
3
4
Door request switch
Pressed
Existed
Released
Not existed
DOOR SWITCH
DLK-95
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR SWITCH
Component Function Check
INFOID:0000000010434603
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “DOOR SW-DR”, “DOOR SW-AS”, “DOOR SW-RL”, “DOOR SW-RR”, “DOOR SW-BK” in “DATA
MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door switch is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000010434604
1.
CHECK DOOR SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect malfunctioning door switch connector.
3.
Check signal between malfunctioning door switch harness connector and ground.
Is the inspection result normal?
YES-1 >> Back door: GO TO 3.
YES-2 >> Other door: GO TO 4.
NO
>> GO TO 2.
2.
CHECK DOOR SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between door switch harness connector and BCM harness connector.
Monitor item
Condition
Status
DOOR SW-DR
Driver side door
Open
On
Closed
Off
DOOR SW-AS
Passenger side door
Open
On
Closed
Off
DOOR SW-RL
Rear door LH
Open
On
Closed
Off
DOOR SW-RR
Rear door RH
Open
On
Closed
Off
DOOR SW-BK
Back door
Open
On
Closed
Off
(+)
(–)
Voltage
Door switch
Connector
Terminal
Driver side
B92
3
Ground
9 - 16 V
Passenger side
B55
Rear LH
B56
Rear RH
B93
Back door
B2
DLK-96
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
DOOR SWITCH
3.
Check continuity between door switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK BACK DOOR SWITCH CIRCUIT
Check continuity between back door lock assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK DOOR SWITCH
DLK-96, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace malfunctioning door switch.
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000010434605
1.
CHECK DOOR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect malfunctioning door switch connector.
3.
Check continuity between door switch terminals.
Door switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
Driver side
B92
3
B4
17
Existed
Passenger side
B55
13
Rear LH
B56
12
Rear RH
B93
10
Back door
B2
11
Door switch
Ground
Continuity
Connector
Terminal
Driver side
B92
3
Not existed
Passenger side
B55
Rear LH
B56
Rear RH
B93
Back door
B2
Back door lock assembly
Ground
Continuity
Connector
Terminal
B2
4
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст