Qashqai J11. Door & Lock — part 7
SUPER LOCK ACTUATOR
DLK-113
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
PASSENGER SIDE
PASSENGER SIDE : Component Function Check
INFOID:0000000010479721
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “SUPER LOCK” in “ACTIVE TEST” mode.
3.
Touch “LOCK” or “UNLOCK” to check that it works normally.
Is the inspection result normal?
YES
>> Super lock actuator is OK.
NO
>> Refer to
DLK-113, "PASSENGER SIDE : Diagnosis Procedure"
.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000010479722
1.
CHECK SUPER LOCK ACTUATOR SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (passenger side) connector.
3.
Check voltage between front door lock assembly (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front door lock assembly (passenger side).
NO
>> GO TO 2.
2.
CHECK SUPER LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM and each door lock assembly.
2.
Check continuity between BCM harness connector and front door lock assembly (passenger side) har-
ness connector.
3.
Check continuity between BCM connector and ground.
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
M68
148
Ground
Super lock
Release
9 – 16 V
149
Set
(+)
(–)
Condition
Voltage
Front door lock assembly (passenger side)
Connector
Terminal
D2
1
Ground
Super lock
Set
9 – 16 V
2
Release
BCM
Front door lock assembly (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M68
139
D2
2
Existed
149
1
BCM
Ground
Continuity
Connector
Terminal
M68
139
Not existed
149
DLK-114
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
SUPER LOCK ACTUATOR
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
REAR LH
REAR LH : Component Function Check
INFOID:0000000010479723
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “SUPER LOCK” in “ACTIVE TEST” mode.
3.
Touch “LOCK” or “UNLOCK” to check that it works normally.
Is the inspection result normal?
YES
>> Super lock actuator is OK.
NO
>> Refer to
DLK-114, "REAR LH : Diagnosis Procedure"
.
REAR LH : Diagnosis Procedure
INFOID:0000000010479724
1.
CHECK SUPER LOCK ACTUATOR OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear door lock assembly LH.
3.
Check voltage between rear door lock assembly LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear door lock assembly LH.
NO
>> GO TO 2.
2.
CHECK SUPER LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM, each door lock actuator and fuel filler lid lock actuator connector.
2.
Check continuity between BCM harness connector and rear door lock assembly LH harness connector.
3.
Check continuity between BCM harness connector and ground.
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
M68
139
Ground
Super lock
Release
9 – 16 V
149
Set
(+)
(–)
Condition
Voltage
Rear door lock assembly LH
Connector
Terminal
D52
1
Ground
Super lock
Set
9 – 16 V
2
Release
BCM
Rear door lock assembly LH
Continuity
Connector
Terminal
Connector
Terminal
B3
124
D52
2
Existed
131
1
SUPER LOCK ACTUATOR
DLK-115
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
REAR RH
REAR RH : Component Function Check
INFOID:0000000010479725
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “SUPER LOCK” in “ACTIVE TEST” mode.
3.
Touch “LOCK” or “UNLOCK” to check that it works normally.
Is the inspection result normal?
YES
>> Super lock actuator is OK.
NO
>> Refer to
DLK-115, "REAR RH : Diagnosis Procedure"
REAR RH : Diagnosis Procedure
INFOID:0000000010479726
1.
CHECK DOOR LOCK ACTUATOR OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear door lock assembly RH.
3.
Check voltage between rear door lock assembly RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear door lock assembly RH.
NO
>> GO TO 2.
2.
CHECK SUPER LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM, each door lock actuator and fuel filler lid lock actuator connector.
2.
Check continuity between BCM harness connector and rear door lock assembly RH harness connector.
BCM
Ground
Continuity
Connector
Terminal
B3
124
Not existed
131
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
B3
124
Ground
Super lock
Release
9 – 16 V
131
Set
(+)
(–)
Condition
Voltage
Rear door lock assembly RH
Connector
Terminal
D65
1
Ground
Super lock
Set
9 – 16 V
2
Release
DLK-116
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
UNLOCK SENSOR
UNLOCK SENSOR
Diagnosis Procedure
INFOID:0000000010434630
1.
CHECK BCM OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check signal between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK UNLOCK SENSOR CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK UNLOCK SENSOR GROUND CIRCUIT
Check continuity between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK UNLOCK SENSOR
DLK-117, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace front door lock assembly (driver side).
5.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
(+)
(–)
Voltage
Front door lock assembly (driver side)
Connector
Terminal
D26
4
Ground
9 – 16 V
BCM
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M69
104
D26
4
Existed
BCM
Ground
Continuity
Connector
Terminal
M69
104
Not existed
Front door lock assembly (driver side)
Ground
Continuity
Connector
Terminal
D26
5
Existed
UNLOCK SENSOR
DLK-117
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
>> INSPECTION END
Component Inspection
INFOID:0000000010434631
1.
CHECK UNLOCK SENSOR
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check continuity between front door lock assembly (driver side) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front lock assembly (driver side).
Front door lock assembly (driver side)
Condition
Continuity
Terminal
4
5
Driver side door
Unlock
Existed
Lock
Not existed
DLK-118
< SYMPTOM DIAGNOSIS >
[TYPE 1]
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
SYMPTOM DIAGNOSIS
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK
SWITCH
ALL DOOR
ALL DOOR : Description
INFOID:0000000010434632
All doors do not lock/unlock using door lock and unlock switch.
ALL DOOR : Diagnosis Procedure
INFOID:0000000010434633
1.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check front door lock and unlock power supply and ground circuit.
Refer to
DLK-109, "FRONT DOOR : Diagnosis Procedure"
(front door) or
DLK-109, "REAR DOOR : Diagnosis
(rear door).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK DOOR LOCK AND UNLOCK SWITCH
Check door lock and unlock switch.
Refer to
DLK-88, "DRIVER SIDE : Component Function Check"
(passenger side).
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK DOOR LOCK ACTUATOR
Check front door lock assembly (driver side).
Refer to
DLK-83, "DRIVER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-94, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
FRONT DOOR
FRONT DOOR : Description
INFOID:0000000010479882
Front doors do not lock/unlock using door lock and unlock switch.
FRONT DOOR : Diagnosis Procedure
INFOID:0000000010479883
1.
CHECK POWER SUPPLY AND GROUND CIRCUIT
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
DLK-119
< SYMPTOM DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SYMPTOM DIAGNOSIS
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK
SWITCH
ALL DOOR
ALL DOOR : Description
INFOID:0000000010434632
All doors do not lock/unlock using door lock and unlock switch.
ALL DOOR : Diagnosis Procedure
INFOID:0000000010434633
1.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check front door lock and unlock power supply and ground circuit.
Refer to
DLK-110, "FRONT DOOR : Diagnosis Procedure"
(front door) or
DLK-110, "REAR DOOR : Diagnosis
(rear door).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK DOOR LOCK AND UNLOCK SWITCH
Check door lock and unlock switch.
Refer to
DLK-89, "DRIVER SIDE : Component Function Check"
(passenger side).
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK DOOR LOCK ACTUATOR
Check front door lock assembly (driver side).
Refer to
DLK-84, "DRIVER SIDE : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-95, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
FRONT DOOR
FRONT DOOR : Description
INFOID:0000000010479882
Front doors do not lock/unlock using door lock and unlock switch.
FRONT DOOR : Diagnosis Procedure
INFOID:0000000010479883
1.
CHECK POWER SUPPLY AND GROUND CIRCUIT
DLK-120
< SYMPTOM DIAGNOSIS >
[TYPE 1]
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
Check front door lock and unlock power supply and ground circuit.
Refer to
DLK-110, "FRONT DOOR : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK DOOR LOCK ACTUATOR
Check front door lock actuator (driver side).
Refer to
DLK-84, "DRIVER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
REAR DOOR
REAR DOOR : Description
INFOID:0000000010479884
Rear doors do not lock/unlock using door lock and unlock switch.
REAR DOOR : Diagnosis Procedure
INFOID:0000000010479885
1.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check rear doors lock and unlock power supply and ground circuit.
Refer to
DLK-110, "REAR DOOR : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK DOOR LOCK ACTUATOR
Check rear door lock actuator.
Refer to
DLK-86, "REAR LH : Component Function Check"
(RH).
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000010434634
Driver side door does not lock/unlock using door lock and unlock switch.
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000010434635
1.
CHECK DOOR LOCK ACTUATOR
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
DLK-121
< SYMPTOM DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Check front door lock assembly (driver side).
Refer to
DLK-84, "DRIVER SIDE : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
PASSENGER SIDE
PASSENGER SIDE : Description
INFOID:0000000010434636
Passenger side door does not lock/unlock using door lock and unlock switch.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000010434637
1.
CHECK DOOR LOCK ACTUATOR
Check front door lock assembly (passenger side).
Refer to
DLK-85, "PASSENGER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
REAR LH
REAR LH : Description
INFOID:0000000010434638
Rear LH side door does not lock/unlock using door lock and unlock switch.
REAR LH : Diagnosis Procedure
INFOID:0000000010434639
1.
CHECK DOOR LOCK ACTUATOR
Check rear door lock assembly LH.
Refer to
DLK-86, "REAR LH : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
REAR RH
DLK-122
< SYMPTOM DIAGNOSIS >
[TYPE 1]
DOOR DOES NOT LOCK/UNLOCK WITH DRIVER SIDE DOOR LOCK KNOB OR
DOOR KEY CYLINDER
DOOR DOES NOT LOCK/UNLOCK WITH DRIVER SIDE DOOR LOCK
KNOB OR DOOR KEY CYLINDER
Diagnosis Procedure
INFOID:0000000010434644
1.
CHECK POWER DOOR LOCK OPERATION
Check power door lock operation.
Does door lock/unlock with door lock and unlock switch?
YES
>> GO TO 2.
NO
>> Go to
DLK-118, "ALL DOOR : Diagnosis Procedure"
2.
CHECK UNLOCK SENSOR
Check unlock sensor.
Refer to
DLK-116, "Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH
DLK-123
< SYMPTOM DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH
ALL DOOR REQUEST SWITCHES
ALL DOOR REQUEST SWITCHES : Description
INFOID:0000000010434645
All doors do not lock/unlock using all door request switches.
ALL DOOR REQUEST SWITCHES : Diagnosis Procedure
INFOID:0000000010434646
1.
CHECK REMOTE KEYLESS ENTRY FUNCTION
Check remote keyless entry function.
Does door lock/unlock with Intelligent Key button?
YES
>> GO TO 2.
NO
>> Refer to
DLK-126, "Diagnosis Procedure"
2.
CHECK “LOCK/UNLOCK BY I-KEY” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT” mode.
3.
Check “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT”.
Refer to
DLK-48, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 1)"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT”.
3.
CHECK INSIDE KEY ANTENNA
Check inside key antenna.
• Console: Refer to
• Luggage room: Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK OUTSIDE KEY ANTENNA
Check outside key antenna.
• Driver side: Refer to
DLK-102, "DRIVER SIDE : Diagnosis Procedure"
DLK-104, "PASSENGER SIDE : Diagnosis Procedure"
.
• Rear bumper: Refer to
DLK-106, "REAR BUMPER : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
DRIVER SIDE DOOR REQUEST SWITCH
DRIVER SIDE DOOR REQUEST SWITCH : Description
INFOID:0000000010434647
All doors do not lock/unlock using driver side door request switch.
DRIVER SIDE DOOR REQUEST SWITCH : Diagnosis Procedure
INFOID:0000000010434648
1.
CHECK DRIVER SIDE DOOR REQUEST SWITCH
Check driver side door request switch.
DLK-124
< SYMPTOM DIAGNOSIS >
[TYPE 1]
DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH
DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH
ALL DOOR REQUEST SWITCHES
ALL DOOR REQUEST SWITCHES : Description
INFOID:0000000010434645
All doors do not lock/unlock using all door request switches.
ALL DOOR REQUEST SWITCHES : Diagnosis Procedure
INFOID:0000000010434646
1.
CHECK REMOTE KEYLESS ENTRY FUNCTION
Check remote keyless entry function.
Does door lock/unlock with Intelligent Key button?
YES
>> GO TO 2.
NO
>> Refer to
DLK-127, "Diagnosis Procedure"
.
2.
CHECK “LOCK/UNLOCK BY I-KEY” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT” mode.
3.
Check “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT”.
Refer to
DLK-48, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 1)"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT”.
3.
CHECK INSIDE KEY ANTENNA
Check inside key antenna.
• Console: Refer to
• Luggage room: Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK OUTSIDE KEY ANTENNA
Check outside key antenna.
• Driver side: Refer to
DLK-103, "DRIVER SIDE : Diagnosis Procedure"
• Passenger side: Refer to
DLK-105, "PASSENGER SIDE : Diagnosis Procedure"
.
• Rear bumper: Refer to
DLK-107, "REAR BUMPER : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
DRIVER SIDE DOOR REQUEST SWITCH
DRIVER SIDE DOOR REQUEST SWITCH : Description
INFOID:0000000010434647
All doors do not lock/unlock using driver side door request switch.
DRIVER SIDE DOOR REQUEST SWITCH : Diagnosis Procedure
INFOID:0000000010434648
1.
CHECK DRIVER SIDE DOOR REQUEST SWITCH
Check driver side door request switch.
DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH
DLK-125
< SYMPTOM DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DLK-93, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK OUTSIDE KEY ANTENNA
Check outside key antenna (driver side).
Refer to
DLK-103, "DRIVER SIDE : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
PASSENGER SIDE DOOR REQUEST SWITCH
PASSENGER SIDE DOOR REQUEST SWITCH : Description
INFOID:0000000010434649
All doors do not lock/unlock using passenger side door request switch.
PASSENGER SIDE DOOR REQUEST SWITCH : Diagnosis Procedure
INFOID:0000000010434650
1.
CHECK PASSENGER SIDE DOOR REQUEST SWITCH
Check passenger side door request switch.
Refer to
DLK-93, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK OUTSIDE KEY ANTENNA
Check outside key antenna (passenger side).
Refer to
DLK-105, "PASSENGER SIDE : Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
BACK DOOR REQUEST SWITCH
BACK DOOR REQUEST SWITCH : Description
INFOID:0000000010434651
All doors do not lock/unlock using back door request switch.
BACK DOOR REQUEST SWITCH : Diagnosis Procedure
INFOID:0000000010434652
1.
CHECK BACK DOOR REQUEST SWITCH
Check back door request switch.
Refer to
DLK-81, "Component Function Check"
.
DLK-126
< SYMPTOM DIAGNOSIS >
[TYPE 1]
DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK OUTSIDE KEY ANTENNA
Check outside key antenna (rear bumper).
Refer to
DLK-107, "REAR BUMPER : Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
DOOR DOES NOT LOCK/UNLOCK WITH INTELLIGENT KEY
DLK-127
< SYMPTOM DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR DOES NOT LOCK/UNLOCK WITH INTELLIGENT KEY
Diagnosis Procedure
INFOID:0000000010434653
1.
CHECK INTELLIGENT KEY
For Intelligent Key that cannot be used for door lock and unlock, check that the Intelligent Key belongs to the
vehicle to be checked.
Does the Intelligent Key belong to the vehicle to checked?
YES
>> GO TO 2.
NO
>> Check Intelligent Key button operation with registered Intelligent Key belonging to the vehicle.
2.
CHECK INTELLIGENT KEY LOW BATTERY WARNING
Check that the Intelligent Key low battery warning is operated.
Is the Intelligent Key low battery warning operated?
YES
>> GO TO 6.
NO-1
>> With another registered Intelligent Key: GO TO 3.
NO-2
>> Without another registered Intelligent Key: GO TO 4.
3.
CHECK INTELLIGENT KEY BUTTON OPERATION
Check that door lock and unlock can be performed by operating the buttons of another registered Intelligent
Key.
Can door lock and unlock be performed with another registered Intelligent Key?
YES
>> GO TO 4.
NO
>> GO TO 7.
4.
CHECK ENGINE START
While depressing the brake pedal, contact the backside of the Intelligent Key that cannot be used to perform
door lock and unlock operation to the push-button ignition switch. Operate the push-button ignition switch, and
check that the vehicle is in START status.
Is the vehicle in START status?
YES
>> GO TO 6.
NO
>> GO TO 5.
5.
CHECK INTELLIGENT KEY
Check the inside of the Intelligent Key for rust or corrosion by water. Simultaneously check the internal circuits
for damage.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace Intelligent Key.
6.
CHECK INTELLIGENT KEY BATTERY
Check the Intelligent Key battery.
Refer to
DLK-100, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace Intelligent Key battery.
7.
CHECK POWER DOOR LOCK OPERATION
Check door lock/unlock using door lock and unlock switch.
Does door lock/unlock using door lock and unlock switch?
YES
>> GO TO 8.
NO
>> Refer to
DLK-119, "ALL DOOR : Diagnosis Procedure"
.
8.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-95, "Component Function Check"
.
DLK-128
< SYMPTOM DIAGNOSIS >
[TYPE 1]
DOOR DOES NOT LOCK/UNLOCK WITH INTELLIGENT KEY
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair or replace the malfunctioning parts.
9.
REPLACE INTELLIGENT KEY
1.
Replace Intelligent Key.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст