Nissan March K13. Manual — part 595
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
SEC-119
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
YES
>> Replace IPDM E/R. Refer to
PCS-28, "Removal and Installation"
.
NO
>> Repair or replace harness.
SEC-120
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
DTC Logic
INFOID:0000000006038609
DTC DETECTION LOGIC
NOTE:
If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Shift selector lever to the P position.
2.
Turn ignition switch ON and wait 1 second or more.
3.
Shift selector lever to the N position and wait 1 second or more.
4.
Shift selector lever to other than the P and N positions and wait 1 second or more.
5.
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT-III.
Is DTC detected?
YES
>> Go to
SEC-120, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006038610
1.
CHECK DTC WITH BCM
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT-III.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK IPDM E/R SIGNAL CIRCUIT OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Disconnect transmission range switch connector.
4.
Check continuity between IPDM E/R harness connector and transmission range switch harness connec-
tor.
5.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210F
INTER LOCK/PNP SW OFF
There is a difference between P/N position
signal from transmission range switch and
P/N position signal (CAN) from BCM.
• Harness or connectors
(The CAN communication line is open
or shorted.)
• Harness or connectors
(Transmission range switch circuit is
open or shorted.)
• Transmission range switch
• IPDM E/R
• BCM
IPDM E/R
Transmission range switch
Continuity
Connector
Terminal
Connector
Terminal
F115
76
F21
10
Existed
(+)
(–)
Continuity
IPDM E/R
Connector
Terminal
F115
76
Ground
Not existed
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
SEC-121
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
YES
>> Replace IPDM E/R. Refer to
PCS-28, "Removal and Installation"
.
NO
>> Repair or replace harness.
SEC-122
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
SECURITY INDICATOR LAMP
SECURITY INDICATOR LAMP
Component Function Check
INFOID:0000000006038616
1.
CHECK FUNCTION
1.
Perform “THEFT IND” in “ACTIVE TEST” mode of “IMMU” of “BCM” using CONSULT-III.
2.
Check security indicator lamp operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
SEC-122, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000006038617
1.
CHECK SECURITY INDICATOR LAMP POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector.
3.
Check voltage between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO-1
>> Check 10 A fuse [No. 11, located in the fuse block (J/B)].
NO-2
>> Check harness for open or short between combination meter and fuse.
2.
CHECK SECURITY INDICATOR LAMP SIGNAL
1.
Connect combination meter connector.
2.
Disconnect BCM connector.
3.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-57, "Removal and Installation"
NO
>> GO TO 3.
3.
CHECK SECURITY INDICATOR LAMP CIRCUIT
1.
Disconnect combination meter connector.
2.
Check continuity between combination meter harness connector and BCM harness connector.
3.
Check continuity between combination meter harness connector and ground.
Test item
Description
THEFT IND
ON
Security indicator lamp
Illuminates
OFF
Does not illuminate
(+)
(–)
Voltage (V)
(Approx.)
Combination meter
Connector
Terminal
M34
1
Ground
Battery voltage
(+)
(–)
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M68
23
Ground
Battery voltage
Combination meter
BCM
Continuity
Connector
Terminal
Connector
Terminal
M34
31
M68
23
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст