Nissan March K13. Manual — part 681

REAR WIPER AUTO STOP SIGNAL CIRCUIT

WW-41

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

REAR WIPER AUTO STOP SIGNAL CIRCUIT

Component Function Check

INFOID:0000000006025192

1.

CHECK REAR WIPER (AUTO STOP) OPERATION

CONSULT-III DATA MONITOR

1.

Select “WIPER” of BCM data monitor item.

2.

Operate the rear wiper.

3.

Check that “RR WIPER STOP” changes to “On” and “Off” linked with the wiper operation.

Is the status of item normal?

YES

>> Rear wiper auto stop signal circuit is normal.

NO

>> Refer to

WW-41, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006025193

1.

CHECK REAR WIPER MOTOR (AUTO STOP) OUTPUT VOLTAGE

1.

Turn ignition switch OFF.

2.

Disconnect rear wiper motor connector.

3.

Turn ignition switch ON.

4.

Check voltage between rear wiper motor harness connector and ground.

Is the inspection result normal?

YES

>> Replace rear wiper motor.

NO

>> GO TO 2.

2.

CHECK REAR WIPER MOTOR (AUTO STOP) CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect BCM connector.

3.

Check continuity between BCM harness connector and rear wiper motor harness connector.

*: With Intelligent Key

4.

Check continuity between BCM harness connector and ground.

*: With Intelligent Key

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-57, "Removal and Installation"

(With Intelligent Key),

BCS-99,

"Removal and Installation"

(Without Intelligent Key).

NO

>> Repair or replace harness.

Monitor item

Condition

Monitor status

RR WIPER STOP

Rear wiper motor

Stop position

On

Except stop position

Off

(+)

(

)

Voltage (Approx.)

Rear wiper motor

Connector

Terminal

D112

4

Ground

Battery voltage

BCM Rear

wiper

motor

Continuity

Connector

Terminal

Connector

Terminal

M66/M69*

44

D112

4

Existed

BCM

Ground

Continuity

Connector

Terminal

M66/M69*

44

Not existed

WW-42

< SYMPTOM DIAGNOSIS >

WIPER AND WASHER SYSTEM SYMPTOMS

SYMPTOM DIAGNOSIS

WIPER AND WASHER SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000006025197

Symptom

Probable malfunction location

Inspection item

Front wiper does not
operate

HI only

• Combination switch
• Harness between combination switch and BCM
• BCM

Combination switch
Refer to

BCS-98, "Symptom

Table"

• IPDM E/R
• Harness between IPDM E/R and front wiper

motor

• Front wiper motor

Front wiper motor (HI) circuit
Refer to

WW-35, "Compo-

nent Function Check"

Front wiper request signal
• BCM
• IPDM E/R

IPDM E/R DATA MONITOR
“FR WIP REQ”

Lo and INT

• Combination switch
• Harness between combination switch and BCM
• BCM

Combination switch
Refer to

BCS-98, "Symptom

Table"

• IPDM E/R
• Harness between IPDM E/R and front wiper

motor

• Front wiper motor

Front wiper motor (LO) circuit
Refer to

WW-34, "Compo-

nent Function Check"

Front wiper request signal
• BCM
• IPDM E/R

IPDM E/R DATA MONITOR
“FR WIP REQ”

INT only

• Combination switch
• Harness between combination switch and BCM
• BCM

Combination switch
Refer to

BCS-98, "Symptom

Table"

Front wiper request signal
• BCM
• IPDM E/R

IPDM E/R DATA MONITOR
“FR WIP REQ”

HI, LO and INT

SYMPTOM DIAGNOSIS
“FRONT WIPER DOES NOT OPERATE”
Refer to

WW-45, "Diagnosis Procedure"

.

Front wiper does not
stop

HI only

• Combination switch
• BCM

Combination switch
Refer to

BCS-98, "Symptom

Table"

Front wiper request signal
• BCM
• IPDM E/R

IPDM E/R DATA MONITOR
“FR WIP REQ”

IPDM E/R

LO only

• Combination switch
• BCM

Combination switch
Refer to

BCS-98, "Symptom

Table"

Front wiper request signal
• BCM
• IPDM E/R

IPDM E/R DATA MONITOR
“FR WIP REQ”

IPDM E/R

INT only

• Combination switch
• BCM

Combination switch
Refer to

BCS-98, "Symptom

Table"

Front wiper request signal
• BCM
• IPDM E/R

IPDM E/R DATA MONITOR
“FR WIP REQ”

WIPER AND WASHER SYSTEM SYMPTOMS

WW-43

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

Front wiper does not
operate normally

Intermittent adjustment
cannot be performed.

• Combination switch
• Harness between combination switch and BCM
• BCM

Combination switch
Refer to

BCS-98, "Symptom

Table"

BCM

Intermittent control
linked with vehicle
speed cannot be per-
formed.

Check the wiper setting is linked with vehicle speed.
Refer to

WW-16, "WIPER : CONSULT-III Function (BCM - WIPER)"

.

Wiper is not linked to
the washer operation.

• Combination switch
• Harness between combination switch and BCM
• BCM

Combination switch
Refer to

BCS-98, "Symptom

Table"

BCM

Does not return to stop
position. [Repeatedly
operates for 10 sec-
onds and then stops
for 20 seconds. (Fail-
safe)]

• IPDM E/R
• Harness between IPDM E/R and front wiper

motor

• Front wiper motor

Front wiper auto stop signal
circuit
Refer to

WW-36, "Compo-

nent Function Check"

Rear wiper does not
operate

ON only

• Combination switch
• Harness between combination switch and BCM
• BCM

Combination switch
Refer to

BCS-98, "Symptom

Table"

INT only

• Combination switch
• Harness between combination switch and BCM
• BCM

Combination switch
Refer to

BCS-98, "Symptom

Table"

ON and INT

• Combination switch
• Harness between combination switch and BCM
• BCM

Combination switch
Refer to

BCS-98, "Symptom

Table"

• BCM
• Harness between rear wiper motor and BCM
• Harness between rear wiper motor and ground
• Rear wiper motor

Combination switch
Refer to

BCS-98, "Symptom

Table"

Rear wiper does not
stop

ON only

• Combination switch
• BCM

Rear wiper motor circuit
Refer to

WW-39, "Compo-

nent Function Check"

.

INT only

• Combination switch
• BCM

Combination switch
Refer to

BCS-98, "Symptom

Table"

Rear wiper does not
operate normally

Wiper is not linked to
the washer operation.

• Combination switch
• Harness between rear wiper motor and BCM
• BCM

Combination switch
Refer to

BCS-98, "Symptom

Table"

BCM

Rear wiper does not
return to the stop posi-
tion. [Stops after a five-
second operation.
(Fail-safe)]

• BCM
• Harness between rear wiper motor and BCM
• Rear wiper motor

Rear wiper auto stop signal
circuit
Refer to

WW-41, "Compo-

nent Function Check"

Symptom

Probable malfunction location

Inspection item

WW-44

< SYMPTOM DIAGNOSIS >

NORMAL OPERATING CONDITION

NORMAL OPERATING CONDITION

Description

INFOID:0000000006025198

FRONT WIPER MOTOR PROTECTION FUNCTION

• IPDM E/R may stop the front wiper to protect the front wiper motor if any obstruction (operation resistance)

such as a large amount of snow is detected during the front wiper operation.

• At that time turn OFF the front wiper and remove the foreign object. Then wait for approximately 20 seconds

or more and reactivate the front wiper. The wiper will operate normally.

REAR WIPER MOTOR PROTECTION FUNCTION

• BCM may stop rear wiper to protect the rear wiper motor when the rear wiper is stopped for 5 seconds or

more due to a snowfall.

• Rear wiper operates normally one minute after the obstacles are removed with rear wiper OFF.

Была ли эта страница вам полезна?
Да!Нет
7 посетителей считают эту страницу полезной.
Большое спасибо!
Ваше мнение очень важно для нас.

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.

Текст

Политика конфиденциальности