Nissan March K13. Manual — part 680
FRONT WIPER MOTOR GROUND CIRCUIT
WW-37
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER MOTOR GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000006025186
1.
CHECK FRONT WIPER MOTOR GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect front wiper motor connector.
3.
Check continuity between front wiper motor harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace harness.
Front wiper motor
Ground
Continuity
Connector
Terminal
E20
5
Existed
WW-38
< DTC/CIRCUIT DIAGNOSIS >
WASHER SWITCH
WASHER SWITCH
Component Inspection
INFOID:0000000006043866
1.
CHECK WASHER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect combination switch connector.
3.
Check continuity between the combination switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace combination switch (Wiper and washer switch).
A
: Terminal 6
B
: Terminal 4
C
: Terminal 1
D
: Terminal 3
JPLIA0164GB
Combination switch
Condition
Continuity
Terminal
1
6
Front washer switch ON
Existed
3
4
1
4
Rear washer switch ON
3
6
REAR WIPER MOTOR CIRCUIT
WW-39
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
REAR WIPER MOTOR CIRCUIT
Component Function Check
INFOID:0000000006025190
1.
CHECK REAR WIPER ON OPERATION
CONSULT-III ACTIVE TEST
1.
Select “RR WIPER” of BCM active test item.
2.
With operating the test item, check rear wiper operation.
Is rear wiper operation normally?
YES
>> Rear wiper motor circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000006025191
1.
CHECK REAR WIPER MOTOR OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1.
Turn ignition switch OFF.
2.
Disconnect rear wiper motor connector.
3.
Turn ignition switch ON.
4.
Select “RR WIPER” of BCM active test item.
5.
With operating the test item, check voltage between rear wiper motor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK REAR WIPER MOTOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and rear wiper motor harness connector.
*: With Intelligent KEY
4.
Check continuity between BCM harness connector and ground.
*: With Intelligent KEY
Is the inspection result normal?
YES
BCS-57, "Removal and Installation"
(With Intelligent Key),
(Without Intelligent Key).
NO
>> Repair or replace harness.
On
: Rear wiper ON operation
Off
: Stop the rear wiper.
(+)
(
−
)
Condition
Voltage (Approx.)
Rear wiper motor
Connector
Terminal
D112
1
Ground
REAR WIPER
On
Battery voltage
Off
0 V
BCM
Rear wiper motor
Continuity
Connector
Terminal
Connector
Terminal
M66/M69*
54
D112
1
Existed
BCM
Ground
Continuity
Connector
Terminal
M66/M69*
54
Not existed
WW-40
< DTC/CIRCUIT DIAGNOSIS >
REAR WIPER MOTOR CIRCUIT
3.
CHECK REAR WIPER MOTOR GROUND OPEN CIRCUIT
Check continuity between rear wiper motor harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear wiper motor.
NO
>> Repair or replace harness.
Rear wiper motor
Ground
Continuity
Connector
Terminal
D112
3
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст