Nissan Murano Z51 (2012 year). Manual — part 54
MIR-44
< REMOVAL AND INSTALLATION >
[WITH ADP]
INSIDE MIRROR
REMOVAL AND INSTALLATION
INSIDE MIRROR
Exploded View
INFOID:0000000007540687
Removal and Installation
INFOID:0000000007540688
CAUTION:
Never reuse the inside mirror disassembled from mirror base.
REMOVAL
1.
Remove the inside mirror cover.
2.
Remove TORX bolt.
3.
Slide the inside mirror upward to remove.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When inserting the inside mirror into the mirror base, be sure to push the pawl until it get connected to
the mirror base.
1.
Inside mirror
2.
Inside mirror cover
3.
Mirror base
4.
TORX bolt
Refer to
for symbols in the figure.
JMLIA0136GB
Revision: 2013 February
2012 MURANO
OUTSIDE MIRROR
MIR-45
< REMOVAL AND INSTALLATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
OUTSIDE MIRROR
DOOR MIRROR ASSEMBLY
DOOR MIRROR ASSEMBLY : Exploded View
INFOID:0000000007540689
REMOVAL
DISASSEMBLY
1.
Door mirror assembly
2.
Front door assembly
3.
Door mirror corner cover
: Clip
JMLIA0122ZZ
JMLIA0123ZZ
Revision: 2013 February
2012 MURANO
MIR-46
< REMOVAL AND INSTALLATION >
[WITH ADP]
OUTSIDE MIRROR
DOOR MIRROR ASSEMBLY : Removal and Installation
INFOID:0000000007540690
CAUTION:
Never damage the mirror bodies.
REMOVAL
1.
Remove the front door finisher. Refer to
INT-12, "FRONT DOOR FINISHER : Removal and Installation"
.
2.
Remove the door mirror corner cover.
3.
Disconnect the door mirror harness connector.
4.
Remove the door mirror mounting nuts, and remove the door mirror assembly.
INSTALLATION
Install in the reverse order of removal.
GLASS MIRROR
GLASS MIRROR : Exploded View
INFOID:0000000007540691
GLASS MIRROR : Disassembly and Assembly
INFOID:0000000007540692
CAUTION:
Never damage the mirror bodies.
DISASSEMBLY
1.
Door mirror cover
2.
Door mirror assembly
3.
Glass mirror
: Pawl
1.
Door mirror cover
2.
Door mirror assembly
3.
Glass mirror
: Pawl
JMLIA0123ZZ
Revision: 2013 February
2012 MURANO
OUTSIDE MIRROR
MIR-47
< REMOVAL AND INSTALLATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
1.
Place the glass mirror upward.
2.
Put a strip of protective tape (A) on the housing.
3.
Insert flat-bladed screwdriver (B) into the recess at lower side
between glass mirror (1) and actuator (2), and push up pawls to
remove glass mirror lower side.
NOTE:
Insert a small slotted screwdriver into recess, and push up while
rotating (twist) to make work easier.
4.
Insert flat-bladed screwdriver at RH/LH side between glass mirror and actuator, and push up pawls to
remove glass mirror RH/LH side.
NOTE:
Insert flat-bladed screwdriver into recesses, and push up while rotating (twist) to make work easier.
5.
Remove two terminals of mirror heater attachment. (With heater mirror model)
6.
Pull glass mirror as shown in the figure in order to disengage
both upper pawls, and then remove glass mirror.
ASSEMBLY
Install in the reverse order of removal.
CAUTION:
After installation, visually check that pawls are securely engaged.
DOOR MIRROR COVER
JMLIA0124ZZ
1.
Glass mirror
2.
Actuator
JMLIA0092ZZ
Revision: 2013 February
2012 MURANO
MIR-48
< REMOVAL AND INSTALLATION >
[WITH ADP]
OUTSIDE MIRROR
DOOR MIRROR COVER : Exploded View
INFOID:0000000007540693
DOOR MIRROR COVER : Disassembly and Assembly
INFOID:0000000007540694
CAUTION:
Never damage the mirror bodies.
DISASSEMBLY
1.
Remove the glass mirror. Refer to
MIR-46, "GLASS MIRROR : Disassembly and Assembly"
2.
Remove the pawls, and disassemble the door mirror cover from the mirror assembly.
ASSEMBLY
Install in the reverse order of removal.
NOTE:
After installation, visually check that pawls are securely engaged.
1.
Door mirror cover
2.
Door mirror assembly
3.
Glass mirror
: Pawl
JMLIA0123ZZ
Revision: 2013 February
2012 MURANO
DOOR MIRROR REMOTE CONTROL SWITCH
MIR-49
< REMOVAL AND INSTALLATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
DOOR MIRROR REMOTE CONTROL SWITCH
Exploded View
INFOID:0000000007540695
INT-12, "FRONT DOOR FINISHER : Exploded View"
Removal and Installation
INFOID:0000000007540696
REMOVAL
1.
Remove the power window main switch finisher (2). Refer to
PWC-92, "Removal and Installation"
2.
Remove door mirror remote control switch (1) from power win-
dow main switch finisher (2) using remover tool (A).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMLIA0118ZZ
Revision: 2013 February
2012 MURANO
MIR-50
< SYSTEM DESCRIPTION >
[WITHOUT ADP]
DOOR MIRROR SYSTEM
SYSTEM DESCRIPTION
DOOR MIRROR SYSTEM
Component Description
INFOID:0000000007540697
Component
Function
Door mirror remote control switch
It supplies power to mirror motor through mirror switch and changeover
switch.
Door mirror
It makes mirror face operate from side to side and up and down with the
mirror control switch operation.
Revision: 2013 February
2012 MURANO
INSIDE MIRROR SYSTEM
MIR-51
< SYSTEM DESCRIPTION >
[WITHOUT ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
INSIDE MIRROR SYSTEM
System Description
INFOID:0000000007540698
The sensor built in inside mirror detects the headlight of the vehicle behind and automatically changes the light
transmission to decrease the brightness.
Component Description
INFOID:0000000007540699
Component
Function
Auto anti-dazzling inside mirror
It automatically changes the light transmittance according to the brightness of the
light from the headlight of the vehicle behind.
Revision: 2013 February
2012 MURANO
MIR-52
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT ADP]
DOOR MIRROR
DTC/CIRCUIT DIAGNOSIS
DOOR MIRROR
Wiring Diagram - DOOR MIRROR SYSTEM (WITHOUT AUTOMATIC DRIVE POSI-
TIONER) -
INFOID:0000000007540700
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JCLWM2740GB
Revision: 2013 February
2012 MURANO
AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM
MIR-53
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM
Wiring Diagram - INSIDE MIRROR SYSTEM -
INFOID:0000000007824628
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JCLWM6099GB
Revision: 2013 February
2012 MURANO
MIR-54
< SYMPTOM DIAGNOSIS >
[WITHOUT ADP]
SQUEAK AND RATTLE TROUBLE DIAGNOSES
SYMPTOM DIAGNOSIS
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Work Flow
INFOID:0000000007540702
CUSTOMER INTERVIEW
Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diag-
nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any of
customer's comments; refer to
MIR-58, "Diagnostic Worksheet"
. This information is necessary to duplicate the
conditions that exist when the noise occurs.
• The customer may not be able to provide a detailed description or the location of the noise. Attempt to obtain
all the facts and conditions that exist when the noise occurs (or does not occur).
• If there is more than one noise in the vehicle, perform a diagnosis and repair the noise that the customer is
concerned about. This can be accomplished by performing a cruise test on the vehicle with the customer.
• After identifying the type of noise, isolate the noise in terms of its characteristics. The noise characteristics
are provided so the customer, service adviser and technician are all speaking the same language when
defining the noise.
• Squeak – (Like tennis shoes on a clean floor)
Squeak characteristics include the light contact/fast movement/brought on by road conditions/hard surfaces
= higher pitch noise/softer surfaces = lower pitch noises/edge to surface = chirping
• Creak – (Like walking on an old wooden floor)
Creak characteristics include firm contact/slow movement/twisting with a rotational movement/pitch depen-
dent on materials/often brought on by activity.
• Rattle – (Like shaking a baby rattle)
Rattle characteristics include the fast repeated contact/vibration or similar movement/loose parts/missing
clip or fastener/incorrect clearance.
• Knock – (Like a knock on a door)
Knock characteristics include hollow sounding/sometimes repeating/often brought on by driver action.
• Tick – (Like a clock second hand)
Tick characteristics include gentle contacting of light materials/loose components/can be caused by driver
action or road conditions.
• Thump – (Heavy, muffled knock noise)
Thump characteristics include softer knock/dead sound often brought on by activity.
• Buzz – (Like a bumblebee)
Buzz characteristics include high frequency rattle/firm contact.
• Often the degree of acceptable noise level will vary depending up on the person. A noise that you may judge
as acceptable may be very irritating to the customer.
• Weather conditions, especially humidity and temperature, may have a great effect on noise level.
DUPLICATE THE NOISE AND TEST DRIVE
SBT842
Revision: 2013 February
2012 MURANO
SQUEAK AND RATTLE TROUBLE DIAGNOSES
MIR-55
< SYMPTOM DIAGNOSIS >
[WITHOUT ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
If possible, drive the vehicle with the customer until the noise is duplicated. Note any additional information on
the Diagnostic Worksheet regarding the conditions or location of the noise. This information can be used to
duplicate the same conditions when you confirm the repair.
If the noise can be duplicated easily during the test drive, to help identify the source of the noise, try to dupli-
cate the noise with the vehicle stopped by doing one or all of the following:
1) Close a door.
2) Tap or push/pull around the area where the noise appears to be coming from.
3) Rev the engine.
4) Use a floor jack to recreate vehicle “twist”.
5) At idle, apply engine load (electrical load, half-clutch on M/T models, drive position on A/T models).
6) Raise the vehicle on a hoist and hit a tire with a rubber hammer.
• Drive the vehicle and attempt to duplicate the conditions the customer states exist when the noise occurs.
• If it is difficult to duplicate the noise, drive the vehicle slowly on an undulating or rough road to stress the
vehicle body.
CHECK RELATED SERVICE BULLETINS
After verifying the customer concern or symptom, check ASIST for Technical Service Bulletins (TSBs) related
to that concern or symptom.
If a TSB relates to the symptom, follow the procedure to repair the noise.
LOCATE THE NOISE AND IDENTIFY THE ROOT CAUSE
1.
Narrow down the noise to a general area. To help pinpoint the source of the noise, use a listening tool
(Chassis Ear: J-39570, Engine Ear and mechanics stethoscope).
2.
Narrow down the noise to a more specific area and identify the cause of the noise by:
• Removing the components in the area that you suspect the noise is coming from.
Do not use too much force when removing clips and fasteners, otherwise clips and fastener can be broken
or lost during the repair, resulting in the creation of new noise.
• Tapping or pushing/pulling the component that you suspect is causing the noise.
Do not tap or push/pull the component with excessive force, otherwise the noise will be eliminated only tem-
porarily.
• Feeling for a vibration with your hand by touching the component(s) that you suspect is (are) causing the
noise.
• Placing a piece of paper between components that you suspect are causing the noise.
• Looking for loose components and contact marks.
MIR-56, "Inspection Procedure"
REPAIR THE CAUSE
• If the cause is a loose component, tighten the component securely.
• If the cause is insufficient clearance between components:
- Separate components by repositioning or loosening and retightening the component, if possible.
- Insulate components with a suitable insulator such as urethane pads, foam blocks, felt cloth tape or ure-
thane tape. A Nissan Squeak and Rattle Kit (J-43980) is available through your authorized Nissan Parts
Department.
CAUTION:
Do not use excessive force as many components are constructed of plastic and may be damaged.
NOTE:
Always check with the Parts Department for the latest parts information.
The following materials are contained in the Nissan Squeak and Rattle Kit (J-43980). Each item can be
ordered separately as needed.
URETHANE PADS [1.5 mm (0.059 in) thick]
Insulates connectors, harness, etc.
76268-9E005: 100
×
135 mm (3.94
×
5.31 in)/76884-71L01: 60
×
85 mm (2.36
×
3.35 in)/76884-
71L02:15
×
25 mm (0.59
×
0.98 in)
INSULATOR (Foam blocks)
Insulates components from contact. Can be used to fill space behind a panel.
73982-9E000: 45 mm (1.77 in) thick, 50
×
50 mm (1.97
×
1.97 in)/73982-
50Y00: 10 mm (0.39 in) thick, 50
×
50 mm (1.97
×
1.97 in)
INSULATOR (Light foam block)
80845-71L00: 30 mm (1.18 in) thick, 30
×
50 mm (1.18
×
1.97in)
FELT CLOTHTAPE
Used to insulate where movement does not occur. Ideal for instrument panel applications.
Revision: 2013 February
2012 MURANO
MIR-56
< SYMPTOM DIAGNOSIS >
[WITHOUT ADP]
SQUEAK AND RATTLE TROUBLE DIAGNOSES
68370-4B000: 15
×
25 mm (0.59
×
0.98 in) pad/68239-13E00: 5 mm (0.20 in) wide tape roll
The following materials, not found in the kit, can also be used to repair squeaks and rattles.
UHMW (TEFLON) TAPE
Insulates where slight movement is present. Ideal for instrument panel applications.
SILICONE GREASE
Used in place of UHMW tape that will be visible or not fit. Will only last a few months.
SILICONE SPRAY
Use when grease cannot be applied.
DUCT TAPE
Use to eliminate movement.
CONFIRM THE REPAIR
Confirm that the cause of a noise is repaired by test driving the vehicle.Operate the vehicle under the same
conditions as when the noise originally occurred. Refer to the notes on the Diagnostic Worksheet.
Inspection Procedure
INFOID:0000000007540703
Refer to Table of Contents for specific component removal and installationinformation.
INSTRUMENT PANEL
Most incidents are caused by contact and movement between:
1.
The cluster lid A and instrument panel
2.
Acrylic lens and combination meter housing
3.
Instrument panel to front pillar garnish
4.
Instrument panel to windshield
5.
Instrument panel mounting pins
6.
Wiring harnesses behind the combination meter
7.
A/C defroster duct and duct joint
These incidents can usually be located by tapping or moving the components to duplicate the noise or by
pressing on the components while driving to stop the noise. Most of these incidents can be repaired by
applying felt cloth tape or silicon spray (in hard to reach areas). Urethane pads can be used to insulate
wiring harness.
CAUTION:
Do not use silicone spray to isolate a squeak or rattle. If you saturatethe area with silicone, you
will not be able to recheck the repair.
CENTER CONSOLE
Components to pay attention to include:
1.
Shifter assembly cover to finisher
2.
A/C control unit and cluster lid C
3.
Wiring harnesses behind audio and A/C control unit
The instrument panel repair and isolation procedures also apply to thecenter console.
DOORS
Pay attention to the:
1.
Finisher and inner panel making a slapping noise
2.
Inside handle escutcheon to door finisher
3.
Wiring harnesses tapping
4.
Door striker out of alignment causing a popping noise on startsand stops
Tapping or moving the components or pressing on them while driving to duplicate the conditions can isolate
many of these incidents. You can usually insulate the areas with felt cloth tape or insulator foam blocks from
the Nissan Squeak and Rattle Kit (J-43980) to repair the noise.
TRUNK
Trunk noises are often caused by a loose jack or loose items put intothe trunk by the owner.
In addition look for:
1.
Trunk lid dumpers out of adjustment
2.
Trunk lid striker out of adjustment
Revision: 2013 February
2012 MURANO
SQUEAK AND RATTLE TROUBLE DIAGNOSES
MIR-57
< SYMPTOM DIAGNOSIS >
[WITHOUT ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
3.
The trunk lid torsion bars knocking together
4.
A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing or insulatingthe item(s) or component(s) caus-
ing the noise.
SUNROOF/HEADLINING
Noises in the sunroof/headlining area can often be traced to one of the following:
1.
Sunroof lid, rail, linkage or seals making a rattle or light knockingnoise
2.
Sunvisor shaft shaking in the holder
3.
Front or rear windshield touching headlining and squeaking
Again, pressing on the components to stop the noise while duplicatingthe conditions can isolate most of these
incidents. Repairs usually consistof insulating with felt cloth tape.
SEATS
When isolating seat noise it's important to note the position the seatis in and the load placed on the seat when
the noise is present. These conditionsshould be duplicated when verifying and isolating the cause of the
noise.
Cause of seat noise include:
1.
Headrest rods and holder
2.
A squeak between the seat pad cushion and frame
3.
The rear seatback lock and bracket
These noises can be isolated by moving or pressing on the suspectedcomponents while duplicating the condi-
tions under which the noise occurs.Most of these incidents can be repaired by repositioning the component
orapplying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or onthe engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1.
Any component mounted to the engine wall
2.
Components that pass through the engine wall
3.
Engine wall mounts and connectors
4.
Loose radiator mounting pins
5.
Hood bumpers out of adjustment
6.
Hood striker out of adjustment
These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move or insulate one component at a time and test drive the vehicle. Also, engine RPM
or load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting, securing, or
insulating the component causing the noise.
Revision: 2013 February
2012 MURANO
MIR-58
< SYMPTOM DIAGNOSIS >
[WITHOUT ADP]
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Diagnostic Worksheet
INFOID:0000000007540704
PIIB8740E
Revision: 2013 February
2012 MURANO
SQUEAK AND RATTLE TROUBLE DIAGNOSES
MIR-59
< SYMPTOM DIAGNOSIS >
[WITHOUT ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
PIIB8742E
Revision: 2013 February
2012 MURANO
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст