Nissan Murano Z51 (2012 year). Manual — part 62
PB-8
< REMOVAL AND INSTALLATION >
PARKING BRAKE SHOE
PARKING BRAKE SHOE
Exploded View
INFOID:0000000007543311
Removal and Installation
INFOID:0000000007543312
REMOVAL
WARNING:
Since dust covering the parking brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
1.
Remove rear tires with power tool.
2.
Remove disc rotor. Refer to
BR-48, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
CAUTION:
Parking brake completely in the released position.
3.
If disc rotor cannot be removed, remove as follows:
a.
Fix the disc rotor with wheel nuts and remove the adjusting hole plug.
b.
Using suitable tool, rotate adjuster (1) in direction (B) to retract
and loosen parking brake shoe.
4.
Remove anti-rattle pins, retainers, anti-rattle spring, adjuster
spring and return springs.
CAUTION:
Never drop the removed parts.
5.
Remove parking brake shoes, adjuster assembly and toggle
lever.
CAUTION:
• The parking brake shoes for the front side are made of dif-
ferent materials from those for the rear side. Never misi-
dentify them when removing.
• Never drop the removed parts.
INSTALLATION
Install in the reverse order of removal.
• Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease to the back plate and brake shoe.
1.
Back plate
2.
Parking brake shoe
3.
Adjuster
4.
Adjuster spring
5.
Return spring
6.
Anti-rattle spring
7.
Retainer
8.
Anti-rattle pin
9.
Toggle lever
: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
JPFIB0046ZZ
JPFIB0007ZZ
Revision: 2013 February
2012 MURANO
PARKING BRAKE SHOE
PB-9
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
CAUTION:
The parking brake shoes for the front side are made of different materials from those for the rear
side. Never misidentify them when removing and replacing.
• Assemble adjusters so that threaded part is expanded when rotat-
ing it in the direction shown by arrow.
• Shorten adjuster by rotating it.
• When disassembling, apply PBC (Poly Butyl Cuprysil) grease or
silicone-based grease to threads.
• Check parking brake shoe sliding surface and drum inner surface
for grease. Wipe it off if it adhere on the surfaces.
Inspection and Adjustment
INFOID:0000000007543313
INSPECTION
Brake Lining Thickness Inspection
• Check thickness (A) of brake lining.
Drum Inner Diameter Inspection
• Check inner diameter (B) of drum.
Other Inspections
• Check brake lining for excessive wear, damage, and peeling. Replace if necessary.
• Check parking brake shoe sliding surface for excessive wear and damage. Replace if necessary.
• Check anti-rattle pin and retainer for excessive wear, damage and rust. Replace if necessary.
• Check adjuster spring, anti-rattle spring and return springs for settling, excessive wear, damage, and rust.
Replace if necessary.
• Check adjuster for smoothness. Replace if necessary.
• Check toggle lever for excessive wear, damage and rust. Replace if necessary.
• Visually check inside of the drum for excessive wear, cracks, and damage with a pair of vernier calipers.
Replace if necessary.
ADJUSTMENT
1.
Adjust the parking brake pedal stroke. Refer to
PB-3, "Inspection and Adjustment"
2.
Check a drag of the parking brake.
A
: For RH brake
B
: For LH brake
: Vehicle front
: Adjuster expands
JPFIB0009ZZ
Limit
A
: Refer to
.
SBR021A
Limit
B
: Refer to
.
JPFIB0008ZZ
Revision: 2013 February
2012 MURANO
PB-10
< REMOVAL AND INSTALLATION >
PARKING BRAKE SHOE
CAUTION:
If any drag is found, inspection the rear disc brake. Refer to
BR-49, "BRAKE CALIPER ASSEMBLY
Revision: 2013 February
2012 MURANO
SERVICE DATA AND SPECIFICATIONS (SDS)
PB-11
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Parking Drum Brake
INFOID:0000000007543314
Unit: mm (in)
Parking Brake Control
INFOID:0000000007543315
Item
Limit
Brake lining
Wear thickness
1.5 (0.059)
Drum
Wear limit of inner diameter
191 (7.52)
Item
Standard
Number of notches [under force of 196 N (20 kg, 44 lb)]
5 – 6 notches
Number of notches when brake warning lamp turns ON
1 notch
Revision: 2013 February
2012 MURANO
PCS
PCS-1
ELECTRICAL & POWER CONTROL
C
D
E
F
G
H
I
J
K
L
B
SECTION
PCS
A
O
P
N
CONTENTS
POWER CONTROL SYSTEM
IPDM E/R
SYSTEM DESCRIPTION . . . . . . . ..
RELAY CONTROL SYSTEM . . . . . . . ..
System Diagram . . . . . . . . . . . . . ....
System Description . . . . . . . . . . . . ...
Component Parts Location . . . . . . . . . ....
POWER CONTROL SYSTEM . . . . . . . .
System Diagram . . . . . . . . . . . . . ....
System Description . . . . . . . . . . . . ...
SIGNAL BUFFER SYSTEM . . . . . . . .
System Diagram . . . . . . . . . . . . . ....
System Description . . . . . . . . . . . . ...
POWER CONSUMPTION CONTROL SYS-
TEM . . . . . . . . . . . . . . . . . .
System Diagram . . . . . . . . . . . . . ....
System Description . . . . . . . . . . . . ...
Component Parts Location . . . . . . . . . ....
DIAGNOSIS SYSTEM (IPDM E/R) . . . . . .
Diagnosis Description . . . . . . . . . . . .
CONSULT Function (IPDM E/R) . . . . . . . .
DTC/CIRCUIT DIAGNOSIS . . . . . . .
U1000 CAN COMM CIRCUIT . . . . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
B2098 IGNITION RELAY ON STUCK . . . ...
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
B2099 IGNITION RELAY OFF STUCK . . . ..
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
POWER SUPPLY AND GROUND CIRCUIT .
Diagnosis Procedure . . . . . . . . . . . ...
ECU DIAGNOSIS INFORMATION . . . ..
IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM) . . . .
Reference Value . . . . . . . . . . . . . ..
Wiring Diagram - IPDM E/R - . . . . . . . . ..
Fail-safe . . . . . . . . . . . . . . . . ...
DTC Index . . . . . . . . . . . . . . . ...
PRECAUTION . . . . . . . . . . . ..
PRECAUTIONS . . . . . . . . . . . . .
FOR USA AND CANADA . . . . . . . . . . ..
FOR MEXICO . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM) . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
POWER DISTRIBUTION SYSTEM
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORK FLOW . ...
Work Flow . . . . . . . . . . . . . . . .
SYSTEM DESCRIPTION . . . . . . . .
Revision: 2013 February
2012 MURANO
PCS-2
POWER DISTRIBUTION SYSTEM . . . . ...
System Description . . . . . . . . . . . . .
Component Parts Location . . . . . . . . . .
Component Description . . . . . . . . . . .
DIAGNOSIS SYSTEM (BCM) . . . . . . .
COMMON ITEM . . . . . . . . . . . . . ....
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . ....
INTELLIGENT KEY . . . . . . . . . . . . ...
INTELLIGENT KEY : CONSULT Function (BCM -
INTELLIGENT KEY) . . . . . . . . . . . ...
DTC/CIRCUIT DIAGNOSIS . . . . . . .
B2553 IGNITION RELAY . . . . . . . . ...
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
B260A IGNITION RELAY . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
B2614 ACC RELAY . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
Component Inspection . . . . . . . . . . ....
B2615 BLOWER RELAY CIRCUIT . . . . ...
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
Component Inspection . . . . . . . . . . ....
B2616 IGNITION RELAY CIRCUIT . . . . ...
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
Component Inspection . . . . . . . . . . ....
B2618 BCM . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
B261A PUSH-BUTTON IGNITION SWITCH . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
POWER SUPPLY AND GROUND CIRCUIT . .
BCM . . . . . . . . . . . . . . . . . . ...
BCM : Diagnosis Procedure . . . . . . . . ...
PUSH-BUTTON IGNITION SWITCH . . . . .
Description . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . .
PUSH-BUTTON IGNITION SWITCH POSI-
TION INDICATOR . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
POWER DISTRIBUTION SYSTEM . . . . ...
Wiring Diagram - PDS (POWER DISTRIBUTION
SYSTEM) - . . . . . . . . . . . . . . . ..
ECU DIAGNOSIS INFORMATION . . . .
BCM (BODY CONTROL MODULE) . . . . ..
Reference Value . . . . . . . . . . . . . .
Wiring Diagram - BCM - . . . . . . . . . . ..
Fail-safe . . . . . . . . . . . . . . . . ..
DTC Inspection Priority Chart . . . . . . . ...
DTC Index . . . . . . . . . . . . . . . ..
PRECAUTION . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . .
FOR USA AND CANADA . . . . . . . . . ...
FOR MEXICO . . . . . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . ...
PUSH-BUTTON IGNITION SWITCH DOES
NOT OPERATE . . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
PUSH-BUTTON IGNITION SWITCH POSI-
TION INDICATOR DOES NOT ILLUMINATE ..
Description . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . .
PUSH BUTTON IGNITION SWITCH . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Revision: 2013 February
2012 MURANO
PCS
RELAY CONTROL SYSTEM
PCS-3
< SYSTEM DESCRIPTION >
[IPDM E/R]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SYSTEM DESCRIPTION
RELAY CONTROL SYSTEM
System Diagram
INFOID:0000000007542269
System Description
INFOID:0000000007542270
IPDM E/R activates the internal control circuit to perform the relay ON-OFF control according to the input sig-
nals from various sensors and the request signals received from control units via CAN communication.
CAUTION:
IPDM E/R integrated relays cannot be removed.
JMMIA0623GB
Revision: 2013 February
2012 MURANO
PCS-4
< SYSTEM DESCRIPTION >
[IPDM E/R]
RELAY CONTROL SYSTEM
NOTE:
: BCM controls the starter relay.
Component Parts Location
INFOID:0000000007542271
Control relay
Input/output
Transmit unit
Control part
Reference page
• Headlamp low relay
• Headlamp high relay
• Low beam request signal
• High beam request signal
BCM (CAN)
• Headlamp low
• Headlamp high
•
(Xenon headlamp)
•
(Halogen headlamp)
Front fog lamp relay
Front fog light request sig-
nal
BCM (CAN)
Front fog lamp
•
(Xenon headlamp)
•
(Halogen headlamp)
Tail lamp relay
Position light request signal
BCM (CAN)
• Parking lamp
• Side marker lamp
• License plate lamp
• Tail lamp
•
(Xenon headlamp)
•
(Halogen headlamp)
Illuminations
• Front wiper relay
• Front wiper high relay
Front wiper request signal
BCM (CAN)
Front wiper
Front wiper stop position
signal
Front wiper motor
Horn relay
• Theft warning horn re-
quest signal
• Horn reminder signal
BCM (CAN)
• Horn (low)
• Horn (high)
• Starter relay
NOTE
• Starter control relay
Starter control relay signal
BCM (CAN)
Starter motor
•
•
Starter relay control signal
TCM
A/C relay
A/C compressor request
signal
ECM (CAN)
A/C compressor
(magnet clutch)
•
(Without 7 inch dis-
play)
•
(With 7 inch display)
• Cooling fan relay-1
• Cooling fan relay-2
• Cooling fan relay-3
Cooling fan speed request
signal
ECM (CAN)
• Cooling fan motor-1
• Cooling fan motor-2
Ignition relay
Ignition switch ON signal
BCM (CAN)
Ignition relay
Vehicle speed signal
Combination meter
(CAN)
Push-button ignition switch
signal
Push-button ignition
switch
JPMIA0870ZZ
Revision: 2013 February
2012 MURANO
PCS
RELAY CONTROL SYSTEM
PCS-5
< SYSTEM DESCRIPTION >
[IPDM E/R]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
1.
IPDM E/R
A.
Engine room (LH)
Revision: 2013 February
2012 MURANO
PCS-6
< SYSTEM DESCRIPTION >
[IPDM E/R]
POWER CONTROL SYSTEM
POWER CONTROL SYSTEM
System Diagram
INFOID:0000000007542272
System Description
INFOID:0000000007542273
ALTERNATOR CONTROL
IPDM E/R outputs power generation command signal (PWM signal) to the alternator according to the status of
the power generation command value signal received from ECM via CAN communication. Refer to
.
JPMIA0908GB
Revision: 2013 February
2012 MURANO
PCS
SIGNAL BUFFER SYSTEM
PCS-7
< SYSTEM DESCRIPTION >
[IPDM E/R]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SIGNAL BUFFER SYSTEM
System Diagram
INFOID:0000000007542274
System Description
INFOID:0000000007542275
• IPDM E/R reads the status of the oil pressure switch and transmits the oil pressure switch signal to BCM via
CAN communication. Refer to
MWI-22, "WARNING LAMPS/INDICATOR LAMPS : System Diagram"
• IPDM E/R receives the rear window defogger control signal from BCM via CAN communication and trans-
mits it to ECM and AV control unit via CAN communication. Refer to
DEF-4, "WITH BOSE SYSTEM : Sys-
.
JPMIA0862GB
Revision: 2013 February
2012 MURANO
PCS-8
< SYSTEM DESCRIPTION >
[IPDM E/R]
POWER CONSUMPTION CONTROL SYSTEM
POWER CONSUMPTION CONTROL SYSTEM
System Diagram
INFOID:0000000007542276
System Description
INFOID:0000000007542277
OUTLINE
• IPDM E/R incorporates a power consumption control function that reduces the power consumption accord-
ing to the vehicle status.
• IPDM E/R changes its status (control mode) with the sleep wake up signal received from BCM via CAN com-
munication.
Normal mode (wake-up)
- CAN communication is normally performed with other control units.
- Individual unit control by IPDM E/R is normally performed.
Low power consumption mode (sleep)
- Low power consumption control is active.
- CAN transmission is stopped.
SLEEP MODE ACTIVATION
• IPDM E/R judges that the sleep-ready conditions are fulfilled when the ignition switch is OFF and none of the
conditions below are present. Then it transmits a sleep-ready signal (ready) to BCM via CAN communica-
tion.
- Outputting signals to actuators
- Switches or relays operating
- Output requests are being received from control units via CAN communication.
• IPDM E/R stops CAN communication and enters the low power consumption mode when it receives a sleep
wake up signal (sleep) from BCM and the sleep-ready conditions are fulfilled.
WAKE-UP OPERATION
• IPDM E/R changes from the low power consumption mode to the normal mode when it receives a sleep
wake-up signal (wake up) from BCM or any of the following conditions is fulfilled. In addition, it transmits a
sleep-ready signal (not-ready) to BCM via CAN communication to report the CAN communication start.
- Ignition switch ON
- An output request is received from a control unit via CAN communication.
JPMIA0906GB
Revision: 2013 February
2012 MURANO
PCS
POWER CONSUMPTION CONTROL SYSTEM
PCS-9
< SYSTEM DESCRIPTION >
[IPDM E/R]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Component Parts Location
INFOID:0000000007542278
1.
Combination meter
2.
IPDM E/R
3.
BCM
4.
Driver seat control unit
5.
Automatic back door control unit
A.
Engine room (LH)
B.
Behind of combination meter
C.
Backside of the seat cushion (driver
seat)
D.
Dash side lower (Passenger side)
JPMIA0899ZZ
Revision: 2013 February
2012 MURANO
PCS-10
< SYSTEM DESCRIPTION >
[IPDM E/R]
DIAGNOSIS SYSTEM (IPDM E/R)
DIAGNOSIS SYSTEM (IPDM E/R)
Diagnosis Description
INFOID:0000000007542279
AUTO ACTIVE TEST
Description
In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp
• Front wiper (LO, HI)
• Parking lamps
• License plate lamps
• Side maker lamps
• Tail lamps
• Front fog lamps
• Headlamps (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan
Operation Procedure
1.
Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2.
Turn the ignition switch OFF.
3.
Turn the ignition switch ON, and within 20 seconds, press the front door switch (driver side) 10 times.
Then turn the ignition switch OFF.
CAUTION:
Close passenger door.
4.
Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
5.
The oil pressure warning lamp starts blinking when the auto active test starts.
6.
After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
When auto active test mode has to be cancelled halfway through test, turn the ignition switch OFF.
CAUTION:
• If auto active test mode cannot be actuated, check door switch system. Refer to
AUTOMATIC BACK DOOR : Component Function Check"
• Do not start the engine.
Inspection in Auto Active Test Mode
When auto active test mode is actuated, the following 6 steps are repeated 3 times.
Operation
sequence
Inspection location
Operation
1
Oil pressure warning lamp
Blinks continuously during operation of auto active test
2
Front wiper
LO for 5 seconds
→
HI for 5 seconds
3
• Parking lamps
• License plate lamps
• Side maker lamps
• Tail lamps
• Front fog lamps
10 seconds
4
Headlamps
LO
⇔
HI 5 times
5
A/C compressor (magnet clutch)
ON
⇔
OFF 5 times
6
Cooling fan
LO for 5 seconds
→
MID for 3 seconds
→
HI for 2 seconds
Revision: 2013 February
2012 MURANO
PCS
DIAGNOSIS SYSTEM (IPDM E/R)
PCS-11
< SYSTEM DESCRIPTION >
[IPDM E/R]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Concept of auto active test
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode
JPMIA0909GB
Symptom
Inspection contents
Possible cause
Any of the following components do not operate
• Parking lamps
• License plate lamps
• Side maker lamps
• Tail lamps
• Front fog lamps
• Headlamp (HI, LO)
• Front wiper (HI, LO)
Perform auto active test.
Does the applicable system
operate?
YES
BCM signal input circuit
NO
• Lamp or motor
• Lamp or motor ground cir-
cuit
• Harness or connector be-
tween IPDM E/R and appli-
cable system
• IPDM E/R
A/C compressor does not operate
Perform auto active test.
Does the magnet clutch oper-
ate?
YES
• A/C amp. signal input circuit
• CAN communication signal
between A/C amp. and
ECM
• CAN communication signal
between ECM and IPDM E/
R
NO
• Magnet clutch
• Harness or connector be-
tween IPDM E/R and mag-
net clutch
• IPDM E/R
Oil pressure warning lamp does not operate
Perform auto active test.
Does the oil pressure warning
lamp blink?
YES
• Harness or connector be-
tween IPDM E/R and oil
pressure switch
• Oil pressure switch
• IPDM E/R
NO
• CAN communication signal
between IPDM E/R and
BCM
• CAN communication signal
between BCM and combi-
nation meter
• Combination meter
Revision: 2013 February
2012 MURANO
PCS-12
< SYSTEM DESCRIPTION >
[IPDM E/R]
DIAGNOSIS SYSTEM (IPDM E/R)
CONSULT Function (IPDM E/R)
INFOID:0000000007542280
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
SELF DIAGNOSTIC RESULT
DATA MONITOR
Monitor item
Cooling fan does not operate
Perform auto active test.
Does the cooling fan operate?
YES
• ECM signal input circuit
• CAN communication signal
between ECM and IPDM E/
R
NO
• Harness or connector be-
tween IPDM E/R and cool-
ing fan motor
• Harness or connector be-
tween IPDM E/R and cool-
ing fan relay
• Cooling fan motor
• Cooling fan relay
• IPDM E/R
Symptom
Inspection contents
Possible cause
Diagnosis mode
Description
Ecu Identification
Allows confirmation of IPDM E/R part number.
Self Diagnostic Result
Displays the diagnosis results judged by IPDM E/R.
Data Monitor
Displays the real-time input/output data from IPDM E/R input/output data.
Active Test
IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor
The results of transmit/receive diagnosis of CAN communication can be read.
Monitor Item
[Unit]
MAIN SIG-
NALS
Description
MOTOR FAN REQ
[1/2/3/4]
×
Displays the value of the cooling fan speed request signal received from ECM via
CAN communication.
AC COMP REQ
[Off/On]
×
Displays the status of the A/C compressor request signal received from ECM via
CAN communication.
TAIL&CLR REQ
[Off/On]
×
Displays the status of the position light request signal received from BCM via CAN
communication.
HL LO REQ
[Off/On]
×
Displays the status of the low beam request signal received from BCM via CAN
communication.
HL HI REQ
[Off/On]
×
Displays the status of the high beam request signal received from BCM via CAN
communication.
FR FOG REQ
[Off/On]
×
Displays the status of the front fog light request signal received from BCM via
CAN communication.
FR WIP REQ
[Stop/1LOW/Low/Hi]
×
Displays the status of the front wiper request signal received from BCM via CAN
communication.
WIP AUTO STOP
[STOP P/ACT P]
×
Displays the status of the front wiper auto stop signal judged by IPDM E/R.
WIP PROT
[Off/BLOCK]
×
Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
IGN RLY1 -REQ
[Off/On]
Displays the status of the ignition switch ON signal received from BCM via CAN
communication.
Revision: 2013 February
2012 MURANO
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст