Nissan Teana J32. Manual — part 1159
TM-160
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
OIL PAN
5.
Remove oil pan gasket (1) from oil pan (2).
6.
Remove magnet (3) from oil pan.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Completely remove all moisture, oil and old gasket, etc. from the oil pan gasket mounting surface of
transaxle case and oil pan.
• Never reuse oil pan gasket, O-ring and oil pan fitting bolts.
• Apply CVT fluid to O-ring.
Inspection
INFOID:0000000003849096
Check foreign materials in oil pan to help determine causes of malfunction. If the CVT fluid is very dark, smells
burned, or contains foreign particles, frictional material (clutches) may need replacement. A tacky film that will
not wipe clean indicates varnish build up. Varnish can cause valves and clutches to stick and can inhibit pump
pressure.
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
SCIA8219J
SECONDARY SPEED SENSOR
TM-161
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SECONDARY SPEED SENSOR
Exploded View
INFOID:0000000003849097
Removal and Installation
INFOID:0000000003849098
REMOVAL
1.
Disconnect the battery cable from negative terminal.
2.
Remove air duct (inlet) and air cleaner case. Refer to
.
3.
Disconnect secondary speed sensor connector.
4.
Remove secondary speed sensor (1) and shim (2).
CAUTION:
Never lose the shim.
5.
Remove O-ring (3) from secondary speed sensor.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to O-ring.
Inspection
INFOID:0000000003849099
After completing installation, check for CVT fluid leakage and check CVT fluid level. Refer to
.
1.
Secondary speed sensor
2.
Shim
3.
Transaxle assembly
4.
O-ring
: Apply CVT Fluid NS-2.
Refer to
for symbols not described above.
JPDIA0687GB
JPDIA0617ZZ
TM-162
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
DIFFERENTIAL SIDE OIL SEAL
DIFFERENTIAL SIDE OIL SEAL
Exploded View
INFOID:0000000003849100
Removal and Installation
INFOID:0000000003849101
REMOVAL
1.
Remove front drive shafts. Refer to
.
2.
Remove differential side oil seals (1) using a flat-bladed screw-
driver (A).
CAUTION:
Be careful not to scratch transaxle case and converter
housing.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Drive each differential side oil seal evenly using a commercial ser-
vice tool so that differential side oil seal protrudes by the dimension
(C) respectively.
Unit: mm (in)
NOTE:
Differential side oil seal pulling direction is used as the reference.
CAUTION:
• Never reuse differential side oil seals.
1.
RH differential side oil seal
2.
LH differential side oil seal
3.
Transaxle assembly
: Apply CVT Fluid NS-2.
Refer to
for symbols not described above.
JPDIA0593ZZ
JPDIA0118ZZ
A
: Transaxle case side
B
: Converter housing side
Dimension C
0
±
0.5 (0
±
0.020)
JPDIA0618ZZ
DIFFERENTIAL SIDE OIL SEAL
TM-163
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Apply CVT fluid to differential side oil seals.
Drift to be used:
Inspection
INFOID:0000000003849102
After completing installation, check for CVT fluid leakage and check CVT fluid level. Refer to
.
Location
Tool number
Transaxle case side
ST33400001
Converter housing side
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст