Nissan Teana J32. Manual — part 353
HOOD
DLK-195
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HOOD SUPPORT ROD : Exploded View
INFOID:0000000003819556
HOOD SUPPORT ROD : Removal and Installation
INFOID:0000000003813389
REMOVAL
1.
Support hood assembly with a proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the hood open when removing the hood
support rod.
2.
Pull hood support rod from grommet and remove.
INSTALLATION
Install in the reverse order of removal.
1.
Hood insulator
2.
Hood hinge (RH/LH)
3.
Hood seal (front) (RH/LH)
4.
Radiator core seal
5.
Grommet
6.
Hood support rod
7.
Clamp
8.
Hood assembly
9.
Hood bumper rubber (lower) (RH/
LH)
10.
Hood bumper rubber (side) (RH/LH)
for symbols in the figure.
JMKIA2380ZZ
DLK-196
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
RADIATOR CORE SUPPORT
RADIATOR CORE SUPPORT
Exploded View
INFOID:0000000003795070
Removal and Installation
INFOID:0000000003795071
REMOVAL
1.
Use refrigerant collecting equipment to discharge the refrigerant. Refer to
.
2.
Remove front under cover. Refer to
EXT-28, "Removal and Installation"
3.
Drain engine coolant from radiator. Refer to
.
4.
Remove front bumper fascia, energy absorber and bumper reinforcement. Refer to
5.
Remove mounting clips and remove air duct cover.
6.
Remove hood lock opener and hood lock. Refer to
DLK-220, "Removal and Installation"
7.
Disconnect connector of horn (HIGH/LOW), and then remove horn (HIGH/LOW). Refer to
8.
Disconnect connector of gas sensor, and then remove gas sensor (with intelligent air conditioner system).
Refer to
VTL-82, "WITH INTELLIGENT AIR CONDITIONER SYSTEM : Removal and Installation"
9.
Remove bumper retainer assembly. Refer to
EXT-12, "Removal and Installation"
10. Remove air guide (RH/LH).
11. Remove front combination lamp (RH/LH). Refer to
EXL-181, "Removal and Installation"
(XENON TYPE)
EXL-343, "Removal and Installation"
(HALOGEN TYPE).
12. Disconnect connector of ambient sensor. Refer to
VTL-24, "Removal and Installation"
(WITHOUT 7 INCH
DISPLAY) or
VTL-81, "Removal and Installation"
(WITH 7 INCH DISPLAY).
1.
Radiator upper hose bracket
2.
Hood switch bracket
3.
Air duct cover
4.
Air guide (RH/LH)
5.
Radiator core support
: Pawl
JMKIA2382ZZ
RADIATOR CORE SUPPORT
DLK-197
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
13. Disconnect connector of refrigerant pressure sensor. Refer to
.
14. Remove mounting bolt, and then remove engine coolant reservoir tank. Refer to
.
15. Remove mounting bolts, and then disconnect condenser pipe assembly. Refer to
.
16. Remove condenser. Refer to
HA-46, "Removal and Installation"
.
17. Remove mounting nut of radiator upper hose from radiator core support, and then remove radiator upper
hose and hood switch bracket. Refer to
.
18. Disconnect radiator upper hose from radiator pipe (upper). Refer to
.
19. Disconnect radiator lower hose (3). Refer to
20. Disconnect CVT fluid cooler hose on radiator side. Refer to
(CVT: RE0F09B) or
(CVT: RE0F10A).
21. Remove power steering oil cooler pipe from radiator core sup-
port at point shown by arrows in the figure.
22. Disconnect connectors of the following parts.
• Cooling fan (RH/LH). Refer to
• Crash zone sensor. Refer to
SR-18, "Removal and Installation"
23. Remove radiator upper clip. Refer to
.
24. Remove all harness clips from radiator core support.
CAUTION:
Never damage radiator.
25. Support hood assembly with a proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the hood open when removing the hood
stay.
26. Remove hood support rod. Refer to
DLK-195, "HOOD SUPPORT ROD : Removal and Installation"
.
27. Remove mounting bolts, and then remove radiator core support.
CAUTION:
• Operate with two workers, because of its heavy weight.
• Never damage power steering oil cooler pipe.
28. Remove the following parts after removing radiator core support.
• Radiator lower hose, radiator upper hose, radiator pipe. Refer to
• Radiator. Refer to
• Cooling fan (RH/LH). Refer to
• Crash zone sensor. Refer to
• Power steering oil cooler pipe clip. Refer to
INSTALLATION
Install in the reverse order of removal.
JMKIA2395ZZ
: harness clip
JMKIA2396ZZ
DLK-198
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
RADIATOR CORE SUPPORT
CAUTION:
• After installation, inspection and replenish the following.
- Engine coolant. Refer to
.
- CVT fluid. Refer to
,
,
(CVT: RE0F10A).
• After installation, adjust the following parts.
- Front combination lamp.
EXL-174, "Aiming Adjustment Procedure (Low Beam)"
Adjustment Procedure (High Beam)"
(XENON TYPE) or
EXL-337, "Aiming Adjustment Procedure
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст