Nissan Teana J32. Manual — part 354
FRONT FENDER
DLK-199
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT FENDER
Exploded View
INFOID:0000000003813392
Removal and Installation
INFOID:0000000003813393
CAUTION:
Use a shop cloth to protect the body from being damaged during removal and installation.
REMOVAL
1.
Remove clips (A) of hood seal assembly (side) (1).
2.
Remove fender protector. Refer to
EXT-22, "FENDER PROTECTOR : Removal and Installation"
3.
Remove front bumper fascia. Refer to
EXT-12, "Removal and Installation"
.
4.
Remove front combination lamp. Refer to
EXL-181, "Removal and Installation"
(XENON TYPE) or
343, "Removal and Installation"
(HALOGEN TYPE).
5.
Remove front fender cover.
6.
Remove center mud guard. Refer to
EXT-26, "Removal and Installation"
1.
Front fender cover
2.
Hood seal assembly (side)
3.
Front fender
: Pawl
JMKIA2383ZZ
JMKIA2397ZZ
DLK-200
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
FRONT FENDER
7.
Remove mounting bolts and remove front fender.
CAUTION:
A viscous urethane foam is installed on the back surface of front fender. When removing the front
fender, peel of the urethane foam bit at a time, and carefully to remove it.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• After installation, check front fender adjustment. Refer to
DLK-193, "HOOD ASSEMBLY : Adjust-
DLK-203, "DOOR ASSEMBLY : Adjustment"
.
• After installation, apply the touch-up paint (the body color) onto the head of front fender mounting
bolts.
• Adjust the following part.
- Front combination lamp: Refer to
EXL-174, "Aiming Adjustment Procedure (Low Beam)"
,
"Aiming Adjustment Procedure (High Beam)"
(XENON TYPE) or
EXL-337, "Aiming Adjustment Pro-
,
EXL-338, "Aiming Adjustment Procedure (High Beam)"
(HALOGEN TYPE).
FRONT DOOR
DLK-201
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT DOOR
DOOR ASSEMBLY
DOOR ASSEMBLY : Exploded View
INFOID:0000000003813394
REMOVAL
ADJUSTMENT
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
JMKIA2384ZZ
DLK-202
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000003813395
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and cloth to protect
door and body.
REMOVAL
1.
Remove mounting bolts of door check link on the vehicle.
2.
Remove front door harness grommet, and then pull out the harness from the vehicle.
3.
Disconnect front door harness connector.
4.
Remove door hinge mounting nuts (door side), and then remove front door assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
TORX bolt
7.
Front door hinge
8.
Rear door hinge (upper)
9.
Rear door hinge (lower)
Refer to
for symbols in the figure.
JMKIA2392GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст