Nissan Teana J32. Manual — part 1131
TM-48
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
P0705 PARK/NEUTRAL POSITION SWITCH
NO
>> GO TO 2.
2.
CHECK HARNESS BETWEEN TCM AND PNP SWITCH (PART 1)
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check continuity between TCM vehicle side harness connector terminals and CVT unit vehicle side har-
ness connector terminals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK HARNESS BETWEEN TCM AND PNP SWITCH (PART 2)
Check continuity between TCM vehicle side harness connector terminals and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
NO
>> Repair or replace damaged parts.
Component Inspection
INFOID:0000000003848959
1.
CHECK PNP SWITCH
Check the continuity of the PNP switch by changing selector lever to various positions and checking continuity
between CVT unit terminals and ground.
TCM vehicle side harness connector
CVT unit vehicle side harness connector
Continuity
Connector
Terminal
Connector
Terminal
F23
1
F24
5
Existed
2
14
3
15
4
18
11
4
TCM vehicle side harness connector
Ground
Continuity
Connector Terminal
F23
1
Not existed
2
3
4
11
P0705 PARK/NEUTRAL POSITION SWITCH
TM-49
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace transaxle assembly. Refer to
Shift position
CVT unit connector
Ground
Continuity
Connector
Terminal
P
F24
4, 5, 14, 15, 18
Not existed
R
4, 15
Existed
5, 14, 18
Not existed
N
4, 5
Existed
14, 15, 18
Not existed
D
4, 5, 14, 15, 18
Existed
L
5, 14, 18
Existed
4, 15
Not existed
TM-50
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
P0710 CVT FLUID TEMPERATURE SENSOR
P0710 CVT FLUID TEMPERATURE SENSOR
Description
INFOID:0000000003848960
The CVT fluid temperature sensor detects the CVT fluid temperature and sends the signal to the TCM.
DTC Logic
INFOID:0000000003848961
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
Immediately after performing any “DTC CONFIRMATION PROCEDURE”, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
1.
CHECK DTC DETECTION
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “Data Monitor” mode for “TRANSMISSION”.
3.
Start engine and maintain the following conditions for at least 10 minutes (total).
With GST
Follow the procedure “With CONSULT-III”.
Is “P0710 ATF TEMP SEN/CIRC” detected?
YES
>> Go to
NO
>> Check intermittent incident. Refer to
GI-35, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000003848962
1.
CHECK CVT FLUID TEMPERATURE SENSOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check resistance between TCM vehicle side harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK HARNESS BETWEEN TCM AND CVT UNIT (CVT TEMPERATURE SENSOR) (PART 1)
1.
Disconnect CVT unit connector.
DTC
Item
(CONSULT-III screen term)
Malfunction is detected when...
Possible cause
P0710
ATF TEMP SEN/CIRC
During running, the CVT fluid temperature
sensor signal voltage is excessively high or
low.
• Harness or connectors
(Sensor circuit is open or shorted.)
• CVT fluid temperature sensor
VEHICLE SPEED
: 10 km/h (6 MPH) or more
ENG SPEED
: 450 rpm or more
ACC PEDAL OPEN
: More than 1.0/8
RANGE
: “D” position
TCM vehicle side harness connector
condition
Resistance (Approx.)
Connector
Terminal
F23
13
25
When CVT fluid temperature is 20
°
C (68
°
F)
6.5 k
Ω
When CVT fluid temperature is 80
°
(176
°
F)
0.9 k
Ω
P0710 CVT FLUID TEMPERATURE SENSOR
TM-51
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
Check continuity between TCM vehicle side harness connector terminals and CVT unit vehicle side har-
ness connector terminals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK HARNESS BETWEEN TCM AND CVT UNIT (CVT TEMPERATURE SENSOR) (PART 2)
Check continuity between TCM vehicle side harness connector terminals and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK CVT FLUID TEMPERATURE SENSOR
Check CVT fluid temperature sensor. Refer to
TM-51, "Component Inspection (CVT Fluid Temperature Sen-
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace transaxle assembly. Refer to
5.
DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
NO
>> Repair or replace damaged parts.
Component Inspection (CVT Fluid Temperature Sensor)
INFOID:0000000003848963
1.
CHECK CVT FLUID TEMPERATURE SENSOR
Check resistance between CVT unit connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace transaxle assembly. Refer to
TCM vehicle side harness connector
CVT unit vehicle side harness connector
Continuity
Connector
Terminal
Connector
Terminal
F23
13
F24
17
Existed
25
19
TCM vehicle side harness connector
Ground
Continuity
Connector
Terminal
F23
13
Not existed
25
CVT unit connector
Condition
Resistance (Approx.)
Connector
terminal
F24
17
19
When CVT fluid temperature is 20
°
C (68
°
F)
6.5 k
Ω
When CVT fluid temperature is 80
°
C (176
°
F)
0.9 k
Ω
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст