Nissan Teana J32. Manual — part 954
RF-82
< ON-VEHICLE REPAIR >
SUNROOF MOTOR ASSEMBLY
SUNROOF MOTOR ASSEMBLY
Exploded View
INFOID:0000000003812887
1.
Roof side finisher RH
2.
Rear link cover
3.
TORX bolt
4.
Glass lid
5.
Roof side finisher LH
6.
Inner blind
7.
Sunroof unit assembly
8.
Sunroof motor assembly
9.
Sunshade motor assembly
Refer to
for symbols in the figure.
JMKIA2488GB
SUNROOF MOTOR ASSEMBLY
RF-83
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
Removal and Installation
INFOID:0000000003812888
REMOVAL
CAUTION:
• Before removing sunroof motor, check that glass lid is fully closed.
• After removing sunroof motor, never attempt to rotate sunroof motor assembly as a single unit.
1.
Remove the headlining. Refer to
INT-54, "SUNROOF : Removal and Installation"
2.
Remove th sunroof motor assembly.
• Disconnect connector (A) from sunroof motor assembly (1).
• Remove sunroof motor assembly mounting screws (B), and
then remove sunroof motor assembly (1).
INSTALLATION
CAUTION:
Before installing the sunroof motor assembly, always place the link and wire assembly in the symmet-
rical and fully closed position.
1.
Move the sunroof motor assembly laterally a little so that the gear is completely engaged into the wire on
the sunroof unit assembly and mounting surface becomes parallel. Then secure the sunroof motor
assembly with screws.
2.
Install the headlining. Refer to
INT-54, "SUNROOF : Removal and Installation"
.
JMKIA2492ZZ
RF-84
< ON-VEHICLE REPAIR >
SUNSHADE MOTOR ASSEMBLY
SUNSHADE MOTOR ASSEMBLY
Exploded View
INFOID:0000000003812889
1.
Roof side finisher RH
2.
Rear link cover
3.
TORX bolt
4.
Glass lid
5.
Roof side finisher LH
6.
Inner blind
7.
Sunroof unit assembly
8.
Sunroof motor assembly
9.
Sunshade motor assembly
Refer to
for symbols in the figure.
JMKIA2488GB
SUNSHADE MOTOR ASSEMBLY
RF-85
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
Removal and Installation
INFOID:0000000003812890
REMOVAL
CAUTION:
• Before removing sunshade motor, check that glass lid is fully closed.
• After removing sunshade motor, never attempt to rotate sunshade motor assembly as a single unit.
1.
Remove the headlining. Refer to
INT-54, "SUNROOF : Removal and Installation"
2.
Remove the sunroof motor assembly.
• Disconnect connector (A) from sunshade motor assembly (1).
• Remove sunshade motor assembly mounting screws (B), and
then remove sunshade motor assembly (1).
INSTALLATION
CAUTION:
Before installing the sunshade motor assembly, always place the link and wire assembly in the sym-
metrical and fully closed position.
1.
Move the sunshade motor assembly laterally a little so that the gear is completely engaged into the wire
on the sunroof unit assembly and mounting surface becomes parallel. Then secure the sunshade motor
assembly with screws.
2.
Install the headlining. Refer to
INT-54, "SUNROOF : Removal and Installation"
.
JMKIA2493ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст