Nissan Teana J32. Manual — part 953
RF-78
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000003812883
Tool name
Description
Engine ear
Locating the noise
Remover tool
Removes the clips, pawls and metal clips
SIIA0995E
PIIB7923J
GLASS LID
RF-79
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
ON-VEHICLE REPAIR
GLASS LID
Exploded View
INFOID:0000000003812884
1.
Roof side finisher RH
2.
Rear link cover
3.
TORX bolt
4.
Glass lid
5.
Roof side finisher LH
6.
Inner blind
7.
Sunroof unit assembly
8.
Sunroof motor assembly
9.
Sunshade motor assembly
Refer to
JMKIA2488GB
RF-80
< ON-VEHICLE REPAIR >
GLASS LID
Removal and Installation
INFOID:0000000003812885
REMOVAL
CAUTION:
Always work with a helper.
1.
Remove the roof side finisher.
• Remove the mounting bolt.
• Remove the clips, and then pull out roof side finisher.
2.
Half open the glass lid.
3.
Remove the TORX bolts from inner side.
• Remove the inner blind.
• Remove the TORX bolts (A).
4.
Remove the TORX bolts from outer side.
• Remove the pawls, and then pull down rear link cover (1).
• Remove the TORX bolts (B).
: Clip
JMKIA2513ZZ
JMKIA2491ZZ
: Pawl
JMKIA2490ZZ
JMKIA1907ZZ
GLASS LID
RF-81
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
5.
Remove the glass lid from the vehicle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
After installing the glass lid, perform the leak test and check that there is no malfunction.
NOTE:
After installation, carry out fitting adjustment. Refer to
.
Adjustment
INFOID:0000000003812886
WEATHER-STRIP OVERLAP ADJUSTMENT AND SURFACE MISMATCH ADJUSTMENT
1.
Tilt up glass lid, and then remove inner blind and rear link cover.
2.
After loosening glass lid from TORX bolts (left and right), tilt down glass lid.
3.
Adjust glass lid from outside of vehicle so it resembles “ A – A” “B – B” as shown in the figure.
4.
To prevent glass lid from moving after adjustment, first tighten the TORX bolts of front left, and then
tighten the TORX bolts of rear right.
5.
Tighten remaining TORX bolts, being careful to prevent glass lid from moving.
6.
Tilt glass lid up and down several times to check that it moves smoothly.
NOTE:
After adjusting the sunroof unit assembly, perform additional service. Refer to
WHEN REPLACING CONTROL UNIT : Special Repair Requirement"
.
JMKIA2506ZZ
a
b
A – A
0.2 - 4.6 mm (0.008 - 0.181 in)
-1.5 - 1.5 mm (-0.059 - 0.059 in)
B – B
0.5 - 4.9 mm (0.020 - 0.193 in)
-1.5 - 1.5 mm (-0.059 - 0.059 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст